Stratasys J826 Mode d'emploi

DOC-18005 Rev. E

3D Printing System

Site Preparation Guide

Stratasys J826

No part of this document may be photocopied, reproduced, or translated into any human or computer language in any

form, nor stored in a database or retrieval system, without prior permission in writing from Stratasys. This document may

be printed for internal use only. All copies, shall contain a full copy of this copyright notice.

www.stratasys.com

Trademarks

Stratasys,and Stratasys J826 are trademarks of Stratasys and/or subsidiaries or affiliates and may be registered in

certain jurisdictions. All other product names and trademarks are the property of their respective owners.

Liability

Stratasys shall not be liable for errors contained herein or for incidental or consequential damages in connection with the

furnishing, performance, or use of this material. Stratasys makes no warranty of any kind with regard to this material,

including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. It is the

responsibility of the system owner/material buyer to determine that Stratasys material is safe, lawful, and technically

suitable for the intended application as well as identify the proper disposal (or recycling) method consistent with local

environmental regulations. Except as provided in Stratasys' standard conditions of sale, Stratasys shall not be

responsible for any loss resulting from any use of its products described herein.

Disclaimers

Customer acknowledges the contents of this document and that Stratasys parts, materials, and supplier are subject to its

standard terms and conditions, available on http://www.stratasys.com/legal/terms-and-conditions-of-sale, which are

incorporated herein by reference.

The specifications and/or information on which this document is based are subject to change without notice.

Feedback

If you have any questions or comments about the way information is presented in this document, or if you have any

suggestions for future editions, please send a message to

c-support@stratasys.com.

DOC-18005 Rev. E

Contents

Introduction 5

About this Guide 5

Installation and Training Schedule 5

Physical Description 6

Size and Weight 6

Shipment and Delivery 7

Shipping Information and Customer Responsibility 7

Shipping Pallet 7

Lifting Equipment 7

Unloading 8

Installation Area 10

Floor Plan (Printer Area) 10

Workstation Requirements 11

Electrical Requirements 12

Power 12

Grounding 12

Circuit Breaker 13

Residual Current Device (RCD) 13

Power Connection 13

UPS (Uninterrupted Power Supply) 13

Communication Lines 15

Local Area Network 15

Telephone 15

Environmental Conditions 16

Temperature and Humidity 16

Air Quality 16

Noise Level 16

Accessories and Utilities 17

Start-Up Kit 17

Exhaust Adapter 17

Compressed Air 18

Fire Safety Equipment 18

Materials Handling and Storage 19

Printing Materials 19

Cleaning Solvent 19

Site Preparation Checklist 20

Introduction

About this Guide

The information and requirements provided in this document ensure proper installation and operation of

the Stratasys J826 printing system. The customer is responsible for preparing the site as described in this

document, and according to any applicable local regulations.

If you have any questions about the information in this document, contact your Stratasys representative.

All site requirements must be met before the installation date. The Site Preparation Checklist should be

submitted to your Stratasys representative. Shipping will be arranged after the checklist is received by

Stratasys.

Non-compliance with requirements specified in this document may result in additional installation

charges.

Installation and Training Schedule

• Basic installation and adjustment: 1 work day

• Operator training (operation and maintenance): 1 work day

• Product designer training (advanced features and work flow): ½ work day

• Practice under supervision: 1½ work days

Stratasys J826 Introduction

Physical Description

The Stratasys J826 printing systems consist of the following main components:

• printer

• material cabinet

• printer computer (built into the printer)

• client workstation provided by the customer

Figure 1 Stratasys J826 printer

Size and Weight

Unit W × H × D

(cm)

W × H × D (inch) Weight (kg/lb)

Printer 87 × 120 × 73.5 34.2 × 47.2 × 29 234 kg / 516 lbs

Materials cabinet 67 x 110 x 64 26.4 x 43.3 x 25.2 152 kg / 335 lbs

Table 1 Size and weight

• W = Width; H = Height; D = Depth

• The depth measurement does not include the fan adapter assembly. If the fan

adapter is ordered, the depth measurement increases to 80 cm/31.5 inches (see

"Exhaust Adapter" on page 17).

Stratasys J826 Physical Description

Shipment and Delivery

Shipping Information and Customer Responsibility

Shipment to the customer will be arranged by a Stratasys distributor as indicated in the “ship to” part of the

invoice.The customer is responsible for providing detailed delivery information, including, whether or not

there is loading dock at the delivery site.

The customer is responsible for transporting the printer to a suitable installation site. Upon request, your

Stratasys service provider will advise regarding these matters.

Note:

Only Stratasys-certified Customer Support Engineers are authorized to unpack and

install equipment supplied.

Shipping Pallet

The following table shows the approximate size and weight of the printing system mounted on a pallet.

Unit W × H × D (cm) W × H × D (inch) Weight (kg/lb)

Stratasys J826 149 × 159 × 138 58.7 × 62.6 × 54.3 425 kg / 936 lb

Materials cabinet 109 × 139 × 94 42.7 × 54.7 × 37 240 kg / 529 lbs

Table 2 Size and weight of printer on shipping pallet

W = Width; H = Height; D = Depth

Lifting Equipment

• lifting capacity: 500 kg (1100 lb)

• extension: 150 cm (60 in.)

Stratasys J826 Shipment and Delivery

Unloading

The unloading area should be a level surface.

An area of 10 m2 (108 sq ft) is required for the forklift to remove the printer from the delivery truck.

A clearance of 120 cm (4 ft) around the back and sides of the packaging is required for unpacking the

printer.

The installation location must be accessible from the unloading area. The customer is responsible for

unloading the printer from the truck and transferring it to the installation location. Minimum space

requirements for unloading the printer are shown in the figure below.

Figure 2 Unloading dimensions—top view

Note:

Dimensions are shown in centimeters.

Stratasys J826 Shipment and Delivery

Figure 3 Printer center of gravity

Stratasys J826 Shipment and Delivery

Installation Area

The installation area should be free of sources of vibration and electromagnetic interference that could

affect the proper functioning of the printer.

The floor gradient should be less than 0.5% (5 mm per meter).

The floor should be stable and able to bear the load of the printer. The minimum floor load is 630 kg/m2

(129 lb/ft2).

The server workstation and the printer should be located in the same room.

The cable between the server workstation and the printer should not exceed 5 meters (16 feet). The

communication cable provided should not be extended or replaced with a longer cable.

Clearance around and above the printer should ensure convenient access and servicing.

The area around the printer should remain dry at all times. Do not place the cleaning station within

5 meters (16 feet) of the printer.

Shelves and cabinets are recommended near the printer for convenient storage of tools, parts,

accessories, manuals, and materials.

Floor Plan (Printer Area)

The following is a sample floor plan, showing the 3D printing system—the printer, the materials cabinet,

and the workstation. The dimensions shown in the figure are the minimum clearance requirements.

Figure 4 Printer floor plan (sample, not to scale)

Stratasys J826 Installation Area

Autres manuels pour J826

Table des matières

Autres manuels Stratasys Imprimante 3D

Stratasys

Stratasys J750 Manuel utilisateur

Stratasys

Stratasys F170 Manuel utilisateur

Stratasys

Stratasys RK1600 WJ Manuel utilisateur

Stratasys

Stratasys Objet30 Manuel utilisateur

Stratasys

Stratasys H350 Manuel utilisateur

Stratasys

Stratasys Objet260 Connex Manuel utilisateur

Stratasys

Stratasys Eden260V Manuel utilisateur

Stratasys

Stratasys F120 Mode d'emploi

Stratasys

Stratasys Fortus 360mc Mode d'emploi

Stratasys

Stratasys FDM Titan Manuel utilisateur

Stratasys

Stratasys Objet30 Manuel utilisateur

Stratasys

Stratasys Objet1000 Connex 2 Manuel utilisateur

Stratasys

Stratasys Fortus 360mc Manuel utilisateur

Stratasys

Stratasys Eden260V Manuel utilisateur

Stratasys

Stratasys Objet260 Connex Manuel utilisateur

Stratasys

Stratasys Fortus 450mc Manuel utilisateur

Stratasys

Stratasys Objet1000 Plus Mode d'emploi

Stratasys

Stratasys Fortus 250mc Manuel utilisateur

Stratasys

Stratasys Dimension 768/Elite Manuel utilisateur

Stratasys

Stratasys F170 Mode d’emploi

Stratasys

Stratasys J850 Manuel utilisateur

Stratasys

Stratasys Origin One Manuel utilisateur

Stratasys

Stratasys Connex500/350 Manuel utilisateur

Stratasys

Stratasys J850 Manuel utilisateur

Manuels Imprimante 3D populaires d'autres marques

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

EcubMaker

EcubMaker TOYDIY Manuel utilisateur

AnyCubic

AnyCubic Kossel Plus Manuel utilisateur

ReDeTec

ReDeTec ProtoCycler Manuel utilisateur

Kywoo3D

Kywoo3D Tycoon IDEX Manuel utilisateur

CraftBot

CraftBot PLUS PRO Manuel utilisateur

3DGence

3DGence INDUSTRY F340 Manuel utilisateur

HP Jet Fusion 4200 Mode d'emploi

Rokit

Rokit AEP Series Manuel utilisateur

AnkerMake

AnkerMake M5 Manuel utilisateur

DIYElectronics

DIYElectronics PRUSA I3 Instructions de montage

Ackuretta

Ackuretta FreeShape 120 Manuel utilisateur

LONGER

LONGER LK5Pro Manuel utilisateur

MakerBot

MakerBot Replicator Manuel utilisateur

ZYYX

ZYYX Pro II Manuel utilisateur

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guide de l'utilisateur

LONGER

LONGER LK4 Pro Manuel utilisateur

German RepRap

German RepRap X400 Pro V3 Manuel utilisateur