Stratasys Objet Series Mode d’emploi

Caution—

To avoid exposure to skin irritants,

wear protective gloves (provided)

throughout this procedure.

DOC-34032 Rev. A

B. Remove screws B.

C. Loosen screw C.

A. Put on protective gloves. Remove the print block cover.

A. Remove the Support print head card.

B. Loosen the print head thumb screws.

Removing the Support Print Head

Support Print Head Replacement Instructions

for Objet Desktop V3 Printers

Page 1

While holding the print head, press down

on the thumb screws and remove it.

DOC-34032 Rev. A

5Make sure you remove the two O-ring

seals along with the print head.

6Protect the print head from UV light if

you plan to re-install it.

Discard the print head

in accordance with

local regulations.

Install the print block cover.

Push on the tab and then pull the jig

downwards to remove it.

DOC-34032 Page 2

Rev. A

Tighten the print head thumb screws.

Press down firmly on the Support print

head card to attach it to the print block.

Installing the Support Print Head

FRONT

PUSH

FIRST

With the print head in the positioning jig,

align it as shown.

Make sure the O-ring seals

are installed on the print head.

FRONT

Remove

Push tab

A. Push jig upwards where marked “Push First.”

B. Push jig upwards where marked “Front.”

A. Insert and tighten screws A.

B. Tighten screw B.

Make sure that the Model head is installed as described in Model Print Head Replacement.

Remove the Model print head card.

Removing the Model Print Head

Model Print Head Replacement Instructions

for Objet Desktop V3 Printers

Page 3

B. Loosen the print head thumb screws.

DOC-34032 Rev. A

Make sure you remove the two O-ring

seals along with the print head.

2While holding the print head, press down

on the thumb screws and remove it.

To replace the Model print head, you must first remove the Support print head

(see page 1).

Protect the print head from UV light if

you plan to re-install it.

Discard the print head

in accordance with

local regulations.

Installing the Model Print Head

Page 4

DOC-34032 Rev. A

After you replace the Model print-head, re-install the Support head (see page 2).

Push on the tab and then pull the jig

downwards to remove it.

Tighten the print head thumb screws.

Press down firmly on the Model print

head card to attach it to the print block.

FRONT

PUSH

FIRST

Make sure the O-ring seals

are installed on the print head.

FRONT

With the print head in the positioning jig,

align it as shown.

3A. Push jig upwards where marked “Push First.”

B. Push jig upwards where marked “Front.”

FRONT

Remove

Push tab

Autres manuels Stratasys Imprimante 3D

Stratasys

Stratasys Fortus 360mc Manuel utilisateur

Stratasys

Stratasys Eden250 Manuel utilisateur

Stratasys

Stratasys F770 Mode d'emploi

Stratasys

Stratasys Objet260 Connex Manuel utilisateur

Stratasys

Stratasys FDM Vantage Series Manuel utilisateur

Stratasys

Stratasys F170 Manuel utilisateur

Stratasys

Stratasys F123 Series Mode d'emploi

Stratasys

Stratasys J750 Manuel utilisateur

Stratasys

Stratasys Dimension Elite Manuel utilisateur

Stratasys

Stratasys F123 Series Manuel utilisateur

Stratasys

Stratasys Objet30 Manuel utilisateur

Stratasys

Stratasys Dimension BST 1200 Manuel utilisateur

Stratasys

Stratasys Dimension BST 1200 Manuel utilisateur

Stratasys

Stratasys Objet24 Manuel utilisateur

Stratasys

Stratasys Eden260VS Mode d'emploi

Stratasys

Stratasys F120 Mode d'emploi

Stratasys

Stratasys Origin One Manuel utilisateur

Stratasys

Stratasys Dimension 768/Elite Manuel utilisateur

Stratasys

Stratasys Objet260 Connex Manuel utilisateur

Stratasys

Stratasys F770 Manuel utilisateur

Stratasys

Stratasys Prodigy Plus Manuel utilisateur

Stratasys

Stratasys V650 Flex Manuel utilisateur

Stratasys

Stratasys P750K Manuel utilisateur

Stratasys

Stratasys F3300 Mode d'emploi

Manuels Imprimante 3D populaires d'autres marques

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

EcubMaker

EcubMaker TOYDIY Manuel utilisateur

AnyCubic

AnyCubic Kossel Plus Manuel utilisateur

ReDeTec

ReDeTec ProtoCycler Manuel utilisateur

Kywoo3D

Kywoo3D Tycoon IDEX Manuel utilisateur

CraftBot

CraftBot PLUS PRO Manuel utilisateur

3DGence

3DGence INDUSTRY F340 Manuel utilisateur

HP Jet Fusion 4200 Mode d'emploi

Rokit

Rokit AEP Series Manuel utilisateur

AnkerMake

AnkerMake M5 Manuel utilisateur

DIYElectronics

DIYElectronics PRUSA I3 Instructions de montage

Ackuretta

Ackuretta FreeShape 120 Manuel utilisateur

LONGER

LONGER LK5Pro Manuel utilisateur

MakerBot

MakerBot Replicator Manuel utilisateur

ZYYX

ZYYX Pro II Manuel utilisateur

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guide de l'utilisateur

LONGER

LONGER LK4 Pro Manuel utilisateur

German RepRap

German RepRap X400 Pro V3 Manuel utilisateur