Stratasys RK1600 WJ Manuel utilisateur

RK1600 WJ

Objet1000 Water Jet –Major Specifications

•Objet1000 Water Jet –RK1600 made by “KRUMM” Germany

•Size: 205+-5 X 205+-5 X 190 cm

•Weight: 680kg

•Ability to clean models in size of: 103.5 X 93 X 90 cm

•Input voltage 220V-240V 50Hz.

•For other input voltages or frequencies power converter is needed

•All electrical malfunctions should be handled by local authorized electricial

System Description front and upper look

Back side

Model Cleaning

1. Open the cleaning unit doors

2. Align the build tray cart with the front of the cleaning unit

3. Align the cart with the cleaning unit

4. Adjust the cart height until it locks into place on the cleaning unit.

5. The build tray can now be rolled into and out of the cleaning unit.

6. Apply the brake of the tray cart

Inserting and Removing the build tray

7. Insert the tray

8. Insert the hands into the openings and press the water gun

WJ installation

1. The unpacking and the placing of the WJ should be done by professional movers and it

is customer’s responsibility

2. In order to place the WJ on it designated place supplied in the start up kit wheels can

be used

Suggested WJ room layout.

Plumbing and GND connections

Before shipment, the cleaning unit is tested and the pump drain plug is

removed, to allow the internal parts of the pump to dry.

If this plug is not installed before connecting the water supply, intake water

will immediately leak from the pump, and flood the area.

Install the threaded plug and washer as shown below.

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels Stratasys Imprimante 3D

Stratasys

Stratasys J826 Mode d'emploi

Stratasys

Stratasys 180-00108 uPrint Manuel utilisateur

Stratasys

Stratasys F900 Manuel utilisateur

Stratasys

Stratasys FDM Titan Manuel utilisateur

Stratasys

Stratasys Connex500/350 Manuel utilisateur

Stratasys

Stratasys J3 Series Manuel utilisateur

Stratasys

Stratasys Objet30 Manuel utilisateur

Stratasys

Stratasys Eden260V Manuel utilisateur

Stratasys

Stratasys J750 Manuel utilisateur

Stratasys

Stratasys Origin One Manuel utilisateur

Stratasys

Stratasys J850 Manuel utilisateur

Stratasys

Stratasys Dimension BST 1200 Manuel utilisateur

Stratasys

Stratasys Eden250 Manuel utilisateur

Stratasys

Stratasys Objet260 Connex Manuel utilisateur

Stratasys

Stratasys J850 Manuel utilisateur

Stratasys

Stratasys Objet24 Guide de configuration

Stratasys

Stratasys FDM Vantage Series Manuel utilisateur

Stratasys

Stratasys J4100 Manuel utilisateur

Stratasys

Stratasys F120 Manuel utilisateur

Stratasys

Stratasys Dimension 768/Elite Manuel utilisateur

Stratasys

Stratasys F120 Mode d'emploi

Stratasys

Stratasys F123 Series Manuel utilisateur

Stratasys

Stratasys H350 Manuel utilisateur

Stratasys

Stratasys Objet Series Mode d’emploi

Manuels Imprimante 3D populaires d'autres marques

Ultimaker

Ultimaker S5 Material Station Manuel utilisateur

EcubMaker

EcubMaker TOYDIY Manuel utilisateur

AnyCubic

AnyCubic Kossel Plus Manuel utilisateur

ReDeTec

ReDeTec ProtoCycler Manuel utilisateur

Kywoo3D

Kywoo3D Tycoon IDEX Manuel utilisateur

CraftBot

CraftBot PLUS PRO Manuel utilisateur

3DGence

3DGence INDUSTRY F340 Manuel utilisateur

HP

HP Jet Fusion 4200 Mode d'emploi

Rokit

Rokit AEP Series Manuel utilisateur

AnkerMake

AnkerMake M5 Manuel utilisateur

DIYElectronics

DIYElectronics PRUSA I3 Instructions de montage

Ackuretta

Ackuretta FreeShape 120 Manuel utilisateur

LONGER

LONGER LK5Pro Manuel utilisateur

MakerBot

MakerBot Replicator Manuel utilisateur

ZYYX

ZYYX Pro II Manuel utilisateur

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guide de l'utilisateur

LONGER

LONGER LK4 Pro Manuel utilisateur

German RepRap

German RepRap X400 Pro V3 Manuel utilisateur