Storage Canopy C3340 Manuel utilisateur

SHELTER

ASSEMBLY MANUAL

Model # W10xL12xH 3.6m

C3340 Back wall & frame of Container Shelter

C3340 Back wall & frame

SPECIFICATION

Width:10m Length:12m Height:3.6m

IMPORTANT----- READ MANUAL FIRST

Impropersite preparation, Assembly and Maintenance may invalidate warranty and cause unnecessaryand costly

mistake. If you have any questions contact your local dealer.

For User Friendly assembly we have identified each individual component with the part code as indicated in the

parts list. Please refer to the part code numbers and drawing to ensure problem free assembly.

It’s necessary to tighten the roof fabric enough to avoid “hammocks” on the roof and also re-tighten once or

twice again after a few months of use. This is important when assembly in cold weather (autumn and winter)

because the fabric is stiff then and when we got the sun and warm weather afterwards it will make the fabric

“slack” again and need to be re-tighten before next winter.

It’s the owners responsibility to take of snow immediately if not slide off by itself.

READ ALL INSTRUCTIONS BEFORE ASSEMBLY

1. Keep work area clean. Cluttered areas invite injuries. Do not set up near snow drifts, in slippery places, in

high winds, or wet location.

2. Keep children away. All children should be kept away from the workarea.

3. Don’t over reach. Keep proper footing and balance at all times.

4. Do not assemble in under the influence of alcohol or drugs. Read warning labels on prescriptions to

determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not

assemble.

5. Be aware of possible windy conditions; fasten the bases in concrete if these conditions are likely to occur.

Remove the cover during hurricane.

6. Be careful with power and heat sources. Do not keep heat sources near the tarpaulin. Do not expose to open

flame.

7. Be aware of personal safety during assembly and use. Be carful not to pinch fingers with clips and tubes

when assembling: when using makes sure there is adequate ventilation for exhaust and other dangerous

fumes.

PartsList

Part Code

Description

Qty

Base plate with tie down ratchet

Lateral base plate with tie down ratchet

Added legs φ76*42cm

Lower standpipe of back wallφ76*2.49m

Middle standpipe of back wallφ76*2.49m

Upper standpipe of back wallφ76*92cm

Upper standpipe of lateral back wall

φ60*74cm

Middle Horizontal Tube for End Wall

φ40*1.55m

Middle Beam for End Wall

group

Middle Suspending Tube

Sidewall Support tube

Lower tensioning tube for roof cover

φ32*1.61m

Back Cover

Ropes

dozen

Bolt M10*60

Bolt M10*90

Bolt

φ12*110

Clip

Stake Peg

Two-place angle seat

Φ60 Clip

Belay objects

SPECIFICATION

Width: 10m Length: 12m Height: 3.6m

IMPORTANT ---- READ MANUALFIRST

Improper site preparation, Assembly and Maintenance may invalidate warranty and cause

unnecessary and costly mistake. If you have any questions contact your local dealer.

For User Friendly assembly we have identified each individual component with the part code as

indicated in the parts list. Please refer to the part code numbers and drawing to ensure problem

free assembly.

It’s necessary to tighten the roof fabric enough to avoid “hammocks” on the roof and also

re-tighten once or twice again after a few months of use. This is important when assembly in cold

weather (autumn and winter) because the fabric is stiff then and when we got the sun and warm

weather afterwards it will make the fabric “slack” again and need to be re-tighten before next

winter.

It’s the owners responsibility to take of snow immediately if not slide off by itself.

READ ALL INSTRUCTIONS BEFORE ASSEMBLY

Keep work area clean. Cluttered areas invite injuries. Do not set up near snow drifts, in

slippery places, in high winds, or wet location.

Keep children away.All children should be kept away from the work area.

Don’t over reach. Keep proper footing and balance at all times.

Do not assemble in under the influence of alcohol or drugs. Read warning labels on

prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If

there is any doubt, do not assemble.

Be aware of possible windy conditions; fasten the bases in concrete if these conditions are

likely to occur. Remove the cover during hurricane.

Be careful with power and heat sources. Do not keep heat sources near the tarpaulin. Do not

expose to open flame.

Be aware of personal safety during assembly and use. Be carful not to pinch fingers with clips

and tubes when assembling: when using makes sure there is adequate ventilation for exhaust and

other dangerous fumes.

EQUIPEMNT AND TOOLS FOR INSTALIATION

1. Measuring tape

2. String for alignment

3. Step ladder

4. Welder

5. Sledge hammer

6. Wrench

7. Scissors

INSTALLATION PROCESS

A—FRAME INSTALLATION

Please refer to the diagram (Figure 1) to install the Frame.

Figure 1

Figure 2

1. The measure is from center to center of the tubes. Referring to the above diagram.

2. As the Figure 1 Shown, assembly the frame for end wall according to above drawing,

No.1 is the Base plate needs to be fixed with stake peg (No.21).

3. No.3 & 4 is the added leg and lower standpipe of back wall, connecting them with (NO.19) boltM8*70.

4. No.8 & 4 is the Upper standpipe of lateral back wall and lower standpipe of back wall, connecting them

with (NO.18) bolt M10*90.

5.The clips (NO.20) is use for connecting the tubes together.

6.Angle seat(No.22) is assembly them together with bent tube,this is use to connect the bent tube and the

main frame, to make it more strong.

7.Assembly the arches one by one, then the frame will be finished like Figure 2.

C- INSTRUCTION FOR COVER ATTACHED

Install the Roof Cover

NOTE: DO NOT install the cover onto the frame of your building in high wind conditions. A slight

breeze is the most advantageous for cover installation. To take advantage of the breeze, pull the

cover up over the arches with the breeze blowing in the cover like a sail filled with air.

1.Use rope(NO.16) to tie the end cover (No.15) to the end wall.

The process is quite easy. But some tightening adjustments will be necessary to produce a flat. Please adjust the

cover timely.

Figure 3

The process is quite easy. But some tightening adjustments will be necessary to

produce a flat. Please adjust the roof cover timely.

Table des matières

Autres manuels Storage Canopy Abri

Storage Canopy

Storage Canopy FB408021P Manuel utilisateur

Storage Canopy

Storage Canopy 26x40x10 Container Shelter Single truss Manuel utilisateur

Storage Canopy

Storage Canopy C604015S Manuel utilisateur

Storage Canopy

Storage Canopy SHELTER Manuel utilisateur

Storage Canopy

Storage Canopy 40x80x15 Manuel utilisateur

Storage Canopy

Storage Canopy FB335017P Manuel utilisateur

Storage Canopy

Storage Canopy FB406021DP Manuel utilisateur

Storage Canopy

Storage Canopy FB406021P Manuel utilisateur

Storage Canopy

Storage Canopy 40x60x15 ST Container shelter Manuel utilisateur

Storage Canopy

Storage Canopy C3340DTPR Manuel utilisateur

Storage Canopy

Storage Canopy 33x40x12 Manuel utilisateur

Storage Canopy

Storage Canopy Two Car Garage Shelter Manuel utilisateur

Storage Canopy

Storage Canopy C2620R Manuel utilisateur

Storage Canopy

Storage Canopy C4040S Manuel utilisateur

Storage Canopy

Storage Canopy FB408021DP Manuel utilisateur

Storage Canopy

Storage Canopy C3340S Manuel utilisateur

Storage Canopy

Storage Canopy C4040 Manuel utilisateur

Storage Canopy

Storage Canopy C4040R Manuel utilisateur

Storage Canopy

Storage Canopy C6040S Manuel utilisateur

Storage Canopy

Storage Canopy C4080S Manuel utilisateur

Storage Canopy

Storage Canopy C3340 Manuel utilisateur

Storage Canopy

Storage Canopy W33 x L40 x H12 ft Manuel utilisateur

Storage Canopy

Storage Canopy C3340DTR Manuel utilisateur

Storage Canopy

Storage Canopy C2640R Manuel utilisateur

Manuels Abri populaires d'autres marques

Tempo Fitness

Tempo Fitness S11 Manuel utilisateur

Tuindeco

Tuindeco 42.7906 Manuel utilisateur

No Butts Bin

No Butts Bin SR1605 Manuel utilisateur

TMG

TMG TMG-DT5040CG Manuel utilisateur

TMG

TMG TMG-DT3063-PRO Manuel utilisateur

EAGLE CLAW

EAGLE CLAW Shappell DX4000 Manuel utilisateur

Kampa

Kampa Poled Shelter 300 Manuel utilisateur

Harnois

Harnois TA-R Manuel utilisateur

Shelters4Less

Shelters4Less SR1551 Manuel utilisateur

TMG

TMG TMG-DT50FW8 Manuel utilisateur

Vikre Handel AS

Vikre Handel AS JIT-1216 Manuel utilisateur

VARNA buildings

VARNA buildings C2020H Manuel utilisateur

Frabill

Frabill ICE HUNTER 195 Manuel utilisateur

Shelters4Less

Shelters4Less SR1588 Manuel utilisateur

Sealey

Sealey Power Products GSS150819SD Manuel utilisateur

Crivit

Crivit 104155 Manuel utilisateur

No Butts Bin

No Butts Bin SR1558-F Manuel utilisateur

TMG

TMG TMG-ST3040C Manuel utilisateur