Storage Canopy ST Container shelter Manuel utilisateur

SHELTER ASSEMBLY

MANUAL

20x40x6.5 ST Container shelter

PARTS LIST

Part Code

Description

Qty

Left base plate

Rigth base plate

Three way fitting

Four way fitting

Top bent tube

Sidewall bent tube

Top roof purling

Connection purlin

Lower tensioning tube for roof cover

2 groups

Angle seat for roof cover

Roof cover

Plastic plug

Ropes

1 dozen

Bolt M8x70

144

Butterfly bolt

14A

Ratchet strap

14B

1.5'' Rachet (With Screws)

SPECIFICATIONS

Width: 20 ft

Length: 40 ft

Height: 6.5 ft

IMPORTANT: READ MANUAL FIRST

Improper site preparation, assembly and maintenance may invalidate warranty and cause

unnecessary and costly mistakes. If you have any questions, contact your local dealer.

For an easy assembly process, we have identified each individual component with the part

code as indicated in the parts list. Please refer to the part code numbers and drawing to

ensure problem-free assembly.

It is necessary to tighten the roof fabric enough to avoid “hammocks” on the roof; also re-

tighten once or twice again after a few months of use. This is important when assembled

during cold seasons (autumn and winter) because the fabric gets stiff in these weather

conditions. When the weather conditions become warmer, the fabric loosens and needs

to be re-tighten

It is the owner’s responsibility to take off snow immediately, otherwise it will slide off on

its own.

READ ALL INSTRUCTIONS BEFORE ASSEMBLY

1. Keep the work area clean. Accidents are more likely in cluttered areas. Do not set

up near snow drifts, in slippery places, in high winds, or wet locations.

2. All children should be kept away from the work area.

3. Don’t overreach. Always keep proper footing and balance.

4. Do not assemble under the influence of alcohol or drugs. Read warning labels on

medication prescriptions to determine if your judgment or reflexes are impaired

while taking them. If there is any doubt, do not assemble.

5. Be aware of possible windy conditions; fasten the bases in concrete if these

conditions are likely to occur. Remove the cover during hurricanes.

6. Be careful with power and heat sources. Do not keep heat sources near the

tarpaulin. Do not expose to open flame.

7. Be aware of personal safety during assembly and use. Be careful not to pinch your

fingers with clips and tubes when assembling: When using, make sure there is

adequate ventilation for any dangerous fumes.

EQUIPMENT AND TOOLS FOR INSTALLATION

1. Measuring tape

2. Alignment string

3. Step ladder

4. Welder

5. Sledgehammer

6. Wrench

7. Scissors

INSTALLATION PROCESS

A - BASE PLATES INSTALLATION

Please refer to the Figure 1 to place the base plates.

Figure 1

1. The measure must be taken from center to center of the base plates. Refer to the

diagram above and confirm the place of the base plates. ENSURE THAT THE

FOUNDATIONS ARE SQUARE.

2. All the base plates need to be welded on the Containers.

B - FRAME INSTALLATION (Refer to figure 2 for these steps)

Figure 2

1. Connect the Three way fitting (part code 1), the Top bent tube (part code 3) and

the Sidewall bent tube (part code 4) with the Bolts M8x70 (part code 13); these

make the external group of arches. DO NOT install the bolts on the top of the truss

where the fabric will rest.

2. Connect the Four way fitting (part code 2), the Top bent tube (part code 3) and the

Sidewall bent tube (part code 4) with the Bolts M8x70 (part code 13); these make

the internal group of arches. Please NOTE the direction of the bolt. DO NOT install

the bolts on the top of the truss where the fabric will rest.

3. Insert one end of the assembled arch into one base plate and force the other end

of the arch into the opposite base plate. Secure the arches in the base plates using

the bolts.

4. After installing the first two arches, connect the Top roof purlin (part code 5) into

the Three way fitting and the Four way fitting using the Butterfly bolt (part code

14).

5. Then connect the Connection purlins (part code 6) on the arches using the Bolts

M8x70 (part code 13). There are 4 pieces of Connection purlins (part code 6) and

one piece of Top roof purlin (part code 5) between each arch.

6. Then install the third arch into the base plate and connect the purlins. Assemble

the arches one by one until the frame is finished.

C - ROOF COVER INSTALLATION

NOTE: DO NOT install the cover onto the frame of your building in high wind conditions. A

slight breeze is the most advantageous for cover installation. To take advantage of the

breeze, pull the cover up over the arches with the breeze blowing in the cover like a sail

filled with air.

1. Insert the Lower tensioning tube for roof cover (part code 7) into the pockets on

the end of the roof cover (part code 9). Then put the Plastic plug (part code 10).

Figure 3

2. Put the Roof cover (part code 9) EVENLY, CAREFULLY AND SLOWLY atop the frame.

Adjust the cover so that it is square and evenly centered on the frame.

Figure 4

3. On the Roof cover, cut pockets over each ratchet on the base plates, then use the

Ratchet strap (part code 14A) to tie down the Lower tensioning tubes.

Figure 5

4. Weld the Angle seats (part code 8) on each container and use Rope (part code 11)

to knit the cover on the two side arches and tie the Roof cover to the Angle seats.

Figure 6

Please, check the detailed installation pictures below:

NOTES:

-DO NOT LEAVE THE ROOF COVER UNATTACHED UNDER ANYCIRCUMSTANCES until

the final assembly and tightening has been completed.

-The process is quite easy, but some tightening adjustments will be necessary to get

a flat, tensioned roof cover. Please adjust the roof cover every month.

-Wrap tape around the gap between the steel after installing.

Table des matières

Autres manuels Storage Canopy Abri

Storage Canopy

Storage Canopy C4060R Manuel utilisateur

Storage Canopy

Storage Canopy C3340 Manuel utilisateur

Storage Canopy

Storage Canopy C3340 Manuel utilisateur

Storage Canopy

Storage Canopy C4040S Manuel utilisateur

Storage Canopy

Storage Canopy DT Container shelter Manuel utilisateur

Storage Canopy

Storage Canopy C2620 Manuel utilisateur

Storage Canopy

Storage Canopy C3340R Manuel utilisateur

Storage Canopy

Storage Canopy 40x40x15 Manuel utilisateur

Storage Canopy

Storage Canopy W33 x L40 x H12 ft Manuel utilisateur

Storage Canopy

Storage Canopy FB408021P Manuel utilisateur

Storage Canopy

Storage Canopy 40x60x15 ST Container shelter Manuel utilisateur

Storage Canopy

Storage Canopy C3340DTPR Manuel utilisateur

Storage Canopy

Storage Canopy SHELTER Manuel utilisateur

Storage Canopy

Storage Canopy FB335017P Manuel utilisateur

Storage Canopy

Storage Canopy Two Car Garage Shelter Manuel utilisateur

Storage Canopy

Storage Canopy 33x40x12 Manuel utilisateur

Storage Canopy

Storage Canopy 26x40x10 Container Shelter Single truss Manuel utilisateur

Storage Canopy

Storage Canopy EWC6040DTR Manuel utilisateur

Storage Canopy

Storage Canopy 40x80x15 Manuel utilisateur

Storage Canopy

Storage Canopy C3340S Manuel utilisateur

Storage Canopy

Storage Canopy C2620R Manuel utilisateur

Storage Canopy

Storage Canopy C4040R Manuel utilisateur

Storage Canopy

Storage Canopy C4060DTR Manuel utilisateur

Storage Canopy

Storage Canopy C604015S Manuel utilisateur

Manuels Abri populaires d'autres marques

Tempo Fitness

Tempo Fitness S11 Manuel utilisateur

Tuindeco

Tuindeco 42.7906 Manuel utilisateur

No Butts Bin

No Butts Bin SR1605 Manuel utilisateur

TMG

TMG TMG-DT5040CG Manuel utilisateur

TMG

TMG TMG-DT3063-PRO Manuel utilisateur

EAGLE CLAW

EAGLE CLAW Shappell DX4000 Manuel utilisateur

Kampa

Kampa Poled Shelter 300 Manuel utilisateur

Harnois

Harnois TA-R Manuel utilisateur

Shelters4Less

Shelters4Less SR1551 Manuel utilisateur

TMG

TMG TMG-DT50FW8 Manuel utilisateur

Vikre Handel AS

Vikre Handel AS JIT-1216 Manuel utilisateur

VARNA buildings

VARNA buildings C2020H Manuel utilisateur

Frabill

Frabill ICE HUNTER 195 Manuel utilisateur

Shelters4Less

Shelters4Less SR1588 Manuel utilisateur

Sealey

Sealey Power Products GSS150819SD Manuel utilisateur

Crivit

Crivit 104155 Manuel utilisateur

No Butts Bin

No Butts Bin SR1558-F Manuel utilisateur

TMG

TMG TMG-ST3040C Manuel utilisateur