StarTech.com PEXSATA22 Manuel utilisateur

PCI Express SATA card

PEXSATA22 Instruction Manual

Actual product may vary from photo

Dual Channel Serial ATA PCI Express Controller Card

FFCCCCCCoommpplliiaanncceeSSttaatteemmeenntt

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

UUsseeooffTTrraaddeemmaarrkkss,,RReeggiisstteerreeddTTrraaddeemmaarrkkss,,aanndd

ootthheerrPPrrootteecctteeddNNaammeessaannddSSyymmbboollss

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and

do not represent an endorsement of a product or service by StarTech.com, or an

endorsement of the product(s) to which this manual applies by the third-party company in

question. Regardless of any direct acknowledgement elsewhere in the body of this

document, StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this

manual and related documents are the property of their respective holders.

TTaabblleeooffCCoonntteennttss

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Instruction Manual

IInnttrroodduuccttiioonn

Thank you for purchasing a StarTech.com PCI Express SATA II two port card - the

perfect solution for adding SATA/SATA II drives to your computer, using the speed and

power of PCI Express. Featuring data transfer speeds of up to 300Mbps, this card can

be used in PCI Express slots with any of the following lane widths (x1, x2, x4, x8, x16),

and is compliant with PCI Specification V2.2 as well as Serial ATA Specification V1.0.

FFeeaattuurreess

• Fully compliant with one-lane 2.5 GB/s PCI Express Specification

• Compliant with Serial ATA 1.0 specifications

• Serial ATA Generation 2 transfer rate of 3.0 Gb/s

• Supports Windows 98, 2000, XP, 2003, Linux, and MAC OS

BBeeffoorreeYYoouuBBeeggiinn

System Requirements

• Pentium-class computer with one available x1 PCI Express slot

• Microsoft Windows 2000, XP or Server 2003, Linux or Mac operating system

• CD-ROM/DVD-ROM drive (driver installation)

Contents

This package should contain:

• SATA PCI-E Host Card (1)

• Serial-ATA Cable (1)

• User Manual (1)

• Driver CD

Instruction Manual

IInnssttaallllaattiioonn

Windows 2000/XP/2003 Fresh Installation

Follow the instructions in this section if you are performing a new installation of Windows

2000/XP/2003, and you wish to boot from a drive attached to the SATA II to PCI Express

Card.

Prior to installation, it is advisable to create a boot diskette. To do so, please locate the

following folder, located on the Driver CD:

D:\Serial-ATA\PCIEXPRESS\Siliconimage\2Ch\Raid driver

Copy all files from this directory onto a blank floppy diskette. Remove the disk from the

drive, and label it accordingly.

1. Shut down all power connected to the computer, as well as all devices connected to

the computer peripherally (i.e. Printers, Monitors, Scanners etc.). As an added step to

ensure safe installation, unplug the power supply from the computer.

2. Remove the computer cover. For more detailed instruction on how to perform this

step, please refer to the documentation that was included with your computer at the

time of purchase.

3. Locate an empty PCI Express slot, removing the metal bracket covering the

accompanying empty port/socket.

4. Position the card above the open PCI Express slot, ensuring that the card is properly

aligned with the slot. Insert the card firmly into the slot, distributing force evenly across

the length of the board. Once inserted, secure the card into the adjoining socket

(previously covered by metal bracket), using the correct size screw (if necessary,

please consult documentation that accompanied purchase of computer).

5. Connect Serial ATA cable(s) between the SATA host card and the Serial ATA device(s).

6. Replace the computer cover and re-connect all power to the computer.

7. Turn on the computer. Upon booting up, Windows will instruct you to Press [ F6 ] for

third party SCSI or driver installation. As such, please hit F6 to continue.

Press [ S ] when setup asks if you want to specify an additional device, and insert the

boot diskette into your floppy drive.

Press [Enter] and select [ Silicon Image SiI 3132 SATALink Serial ATA Controller ].

Press [Enter] again when prompted to continue on with text mode setup.

Follow the setup instructions to select your choice for partition and file system.

After setup examines your disks, it will copy files from the CD to the hard drive

selected above and restart the system. After restart, the setup process will resume

installing the new drive(s).

Instruction Manual

Adding the SATA host card to an existing Windows 2000/XP installation

Follow the instructions in this section to install the SATA host card on a system already

running Windows 2000 or Windows XP.

1. Shut down all power connected to the computer, as well as all devices connected to

the computer peripherally (i.e. Printers, Monitors, Scanners etc.). As an added step to

ensure safe installation, unplug the power supply from the computer.

2. Remove the computer cover. For more detailed instruction on how to perform this

step, please refer to the documentation that was included with your computer at the

time of purchase.

3. Locate an empty PCI Express slot, removing the metal bracket covering the

accompanying empty port/socket.

4. Position the card above the open PCI Express slot, ensuring that the card is properly

aligned with the slot. Insert the card firmly into the slot, distributing force evenly across

the length of the board. Once inserted, secure the card into the adjoining socket

(previously covered by metal bracket), using the correct size screw (if necessary,

please consult documentation that accompanied purchase of computer).

5. Connect Serial ATA cable(s) between the SATA host card and the Serial ATA device(s).

6. Replace the computer cover and re-connect all power to the computer.

7. Turn on the computer. During boot up, Windows will display the Found New

Hardware Wizard. When you see the screen depicted below, please select No, not

this time, and click Next.

Instruction Manual

3. Select Include this location in the search, and click Browse. The necessary files

are located in: D: \Serial-ATA\PCIEXPRESS\Siliconimage\2Ch\Raid driver, where

D:\ is the drive letter designating your CD-ROM/DVD-ROM drive. Once this file has

been selected, click Next.

4. The wizard will now copy the required files to the system and begin installing the

driver. Once the driver has been installed, the wizard will display a completion dialog.

Click Finish to exit the wizard.

Instruction Manual

Verifying installation

Windows 2000/XP/2003

1. Right-click on the My Computer icon. Select Properties, and left-click on the

Hardware tab. Click on the Device Manager button. Double click on SCSI and RAID

Controllers. If there is no yellow [ !] or [ ?] in front of the listing for Silicon Image SiI

3132 Serial ATA Controller, the driver has successfully been installed.

2. To view information about the devices attached to the controller, right click the Silicon

Image SiI 3132 Serial ATA Controller and select Properties from the context menu,

then select the tab labeled Device Info.

Instruction Manual

Updating drivers on Windows 2000/XP/2003

With the SATA host card already plugged in and the driver already installed, follow the

instructions below to update the SATA host driver:

1. Right click on My Computer and select Properties. Under the System Properties

section, click on the Hardware tab, and then on Device Manager. Click SCSI and

RAID Controllers and right-click on Silicon Image SiI 3132 Serial ATA Controller,

then select Properties from the context menu.

2. Click on the Update Driver button on the Driver tab, and select Search for a suitable

driver for my device (Recommended) . Insert the Driver CD into the CD-ROM drive.

3. Click Next to complete the driver installation.

4. The system will go through the enumeration process and install the driver.

Once Windows finds the necessary file, it will ask if you wish to continue with the

update. Please click Next to update the driver. At the end of the process, click Yes to

reboot the computer.

After rebooting, ensure that the update was successful, by following the same steps used

to verify installation was complete.

Instruction Manual

Serial ATA Host Card GUI Utility installation

Insert the Driver CD into the computer’s CD-ROM drive. When the autorun window

appears, select the path D:\Serial-ATA\PCIEXPRESS\Siliconimage\2Ch\GUI, where D:\

specifies your CD-ROM/DVD-ROM drive.

1. Click on GUI.exe

2. Click Next. If you wish to specify a location for the software installation other than that

specified by default, please make your selection now. Click Next, once the folder has

been specified.

3. Choose the GUI function by placing a checkmark next to GUI, and click Next.

4 . Once the GUI is installed, you will be notified and given the option to click Finish.

Please do so, to allow the system to reboot.

Instruction Manual

Autres manuels StarTech.com Carte PCI

StarTech.com

StarTech.com PEXUSB312A2 Manuel utilisateur

StarTech.com

StarTech.com PCI1P2 Manuel utilisateur

StarTech.com

StarTech.com PEXUSB321C Manuel utilisateur

StarTech.com

StarTech.com PCI2S1P2 Manuel utilisateur

StarTech.com

StarTech.com PEXUSB3S23 Manuel du système

StarTech.com

StarTech.com PEX4S553S Manuel utilisateur

StarTech.com

StarTech.com PCISAT2IDE1 Manuel utilisateur

StarTech.com

StarTech.com PEX1P Manuel utilisateur

StarTech.com

StarTech.com PEX100SFP Manuel du système

StarTech.com

StarTech.com PCI2S650PW Manuel utilisateur

StarTech.com

StarTech.com PCISATA2A133 Manuel utilisateur

StarTech.com

StarTech.com PCISOUND5CH Manuel utilisateur

StarTech.com

StarTech.com PEXUSB3S2E2I Manuel utilisateur

StarTech.com

StarTech.com USB32VGCAPRO Manuel utilisateur

StarTech.com

StarTech.com PEX4RISER Manuel utilisateur

StarTech.com

StarTech.com PCI4S550 Manuel utilisateur

StarTech.com

StarTech.com USB2HDCAPM Manuel utilisateur

StarTech.com

StarTech.com PEX3U3F800 Manuel utilisateur

StarTech.com

StarTech.com PCISCSIU2W Manuel utilisateur

StarTech.com

StarTech.com PEX300WN2X3 Manuel utilisateur

StarTech.com

StarTech.com PEXSAT34 Manuel du système

StarTech.com

StarTech.com PEX8S950LP Manuel utilisateur

StarTech.com

StarTech.com PCISCSI2 Manuel utilisateur

StarTech.com

StarTech.com PCI2S650DVLP Manuel utilisateur

Manuels Carte PCI populaires d'autres marques

ERMA

ERMA SSI 1417 Manuel utilisateur

SIIG

SIIG CyberSerial Dual PCI Instructions de montage

Moxa Technologies

Moxa Technologies CP-102E Manuel utilisateur

I-Bus

I-Bus IBC2602 Manuel utilisateur

Exsys

Exsys EX-60102 Manuel utilisateur

Chelsio Communications

Chelsio Communications T5 Series Manuel utilisateur

Conrad Electronic

Conrad Electronic 97 46 71 Manuel utilisateur

Micro Innovations

Micro Innovations USB650A Manuel utilisateur

KTI Networks

KTI Networks KF-310 Manuel utilisateur

Asus

Asus SpaceLink WL230 Manuel utilisateur

SIIG

SIIG SC2475 Manuel utilisateur

TRENDnet

TRENDnet TEW-703PI Manuel utilisateur

Belkin

Belkin F5D7000F Manuel utilisateur

Pericom

Pericom PI7C7100 Manuel utilisateur

ADLINK Technology

ADLINK Technology cPCI-3548 Manuel utilisateur

Digium

Digium TE200 Series Manuel utilisateur

Allo.com

Allo.com 2nd Gen E1/T1/J1 Manuel utilisateur

Western Digital

Western Digital FireWire PCI Adapter Manuel utilisateur