SIIG Cyber PCI I/O Manuel utilisateur

Cyber PCI I/O

Quick Installation Guide

04-0201C

Introducing the Cyber PCI I/O

The Cyber PCI I/O high-speed serial and parallel I/O card family

provides a complete solution for serial and parallel device

connections. It provides 16550/16650/16850 UART serial port(s)

which supports data transfer rates up to 920Kbps and ECP/EPP

parallel port(s) which supports data transfer rates up to 2MB/sec.

Since this installation guide is written for all Cyber PCI I/O boards,

some features on this installation guide might not be present on the

model you bought. Please only refer to the features that apply to

your board.

Features and Benefits

•Conforms to PCI v2.1 Plug and Play

•Full support for DOS- and Windows-based software

•Improves I/O access speed up to 8 times faster than existing

ISA-bus serial ports. Reduces CPU load and improves system

performance dramatically

•IRQ sharing feature eliminates IRQ conflicts

Serial interface:

•High-speed 16550/16650/16850 UART serial port (9-pin)

supports baud rates up to 920Kbps. Works with 56K V.90

external modems, ISDN terminal adapters, PDAs, digital

cameras, label printers and other serial port devices

•Built-in 16/32/128-byte FIFO buffers dramatically increase

data transmit/receive speed, especially under Windows

multitasking environment

Parallel interface:

• Conforms to IEEE 1284-1994 parallel port standard

• High-speed parallel port supports various types of parallel

port devices including removable cartridge drives, CD-R/

RWs, printers, SuperDiskTM LS-120 drives, scanners and more

• Supports EPP, ECP(PIO mode), Bi-directional Parallel Port

(BPP) and Standard Parallel Port (SPP) modes

System Requirements

•Pentium or equivalent computer with an available 32-bit PCI

slot

•DOS/Windows 3.1x, Windows 95/98/98 SE/ME/NT 4.0/

2000/XP

Package Contents

• One Cyber PCI I/O board

• One floppy driver diskette

• One 5-year warranty card

• This quick installation guide

Hardware Installation

Generalinstructionsforinstallingthecardareprovidedbelow,since

the design of computer cases and motherboards vary. Refer to your

computer’s reference manual for further information, if needed.

Caution: StaticElectricityDischargemaypermanentlydamageyour

system. To avoid possible static electricity discharge during the

installation, please follow the guidelines below:

•Dischargeanystaticelectricitybuildupinyourbodybytouching

alargegroundedmetalsurfaceorthecomputer’scase(ifplugged

in), forafewseconds.

•During the installation, avoid any contact with internal parts.

Handle cards only by their external edges.

1. Turn OFF the power to your computer and any other connected

peripheral devices.

2. Unplug the power cord from the back of the computer.

3. Remove your computer’s cover.

4. Remove the slot bracket from an available PCI slot.

5. To install the card, carefully align the card's bus connector with

the selected PCI slot on the motherboard. Push the board down

firmly, but gently, until it is well seated.

6. Replace the slot bracket's holding screw to secure the card.

7. Replace the computer cover and reconnect the power cord.

Software Installation

This section provides information on how to install the

Cyber PCI I/O's drivers for the following operating systems:

Windows 95/98/98 SE/ME

Windows NT 4.0

Windows 2000/XP

DOS/Windows 3.1x

Windows 95 Driver Installation

1. At the Add New Hardware Wizard window, click Next.

2. Insert the Driver Installation diskette in the floppy drive, and

click Other Locations. Type in a:\Win95, click OK, then

Finish.

3. From the Insert Disk window, click OK. When the Copying

Files dialog box appears, type in a:\Win95, then click OK.

4. Remove the diskette and select Yes to restart your system.

Windows 98/98 SE Driver Installation

1. At the Add New Hardware Wizard window, click Next.

2. Select Search for the best driver for your devices

(Recommend), then click Next.

3. Select Specify a location, insert the Driver Installation diskette

and type in a:\Win98, then click Next.

4. Click Next, then Finish.

5. Remove the diskette and click Yes to restart your system.

Windows ME Driver Installation

1. At the Add New Hardware Wizard screen, choose Specify

the location of the driver (Advanced), then click Next.

2. Check Specify a location, insert the Driver Installation

diskette into your floppy drive, type in A:\Win98, then click

Next.

3. Click Next, and Finish to complete driver installation.

4. Remove the driver diskette and click Yes to restart Windows.

To verify successful installation in Windows 95/98/98 SE/ME:

1. From the main desktop, double click My Computer, Control

Panel,System,then click Device Manager.

2. Double click Ports (COM & LPT) and new Cyber PCI ports

should be displayed. Also, double click SIIG Cyber PCI

option and SIIG ... PCI Board should be displayed.

The board is ready to connect new devices.

Windows NT 4.0 Driver Installation

1. From the desktop click Start, then Run.

2. Insert the Driver Installation diskette, type in A:\NT4\setup,

then click OK.

3. Click Next when the Welcome window appears.

4. From Choose Destination Location window, click Next.

5. Remove the Driver Installation diskette, select Yes to restart

Windows and click Finish.

To verify successful installation in Windows NT 4.0:

1. Go to Start / Setting / Control Panel,double click SIIG Cyber

PCI 20X device icon.

2. New COM port address and LPT number will be assigned for

the ports when successfully installed. The board is ready to

connect devices.

Note If you plan to connect a parallel device other than a

printer to the parallel port, such as zip drive, or scanner,

please follow the next section to change the port's I/O

address to support these devices.

To change the I/O address in Windows NT 4.0:

1. Double click Start, Settings, Control Panel,then SIIG Cyber

PCI 20X device icon.

2. Highlight the LPT or COM address and click Settings.

3. Select or type in an I/O address supported by the device you

would like to configure and click OK. Make sure the selected

I/O address does not conflict with other device in your

system.

4. Select Restart Now for the new setup to take effect.

Windows 2000 Driver Installation

Windows 2000 will automatically detect and install the correct

driver for the CyberSerial PCI and CyberParallel PCI boards.

For the rest of the Cyber PCI I/O boards, please follow the

instructions below:

1. At the New Hardware Wizard, click Next.

2. Select Search for a suitable driver for my device

(recommended) and click Next.

3. Select Specify a location, uncheck the other options and click

Next.

4. Insert the Driver Installation diskette, type in A:\Win2K and

click OK.

5. Click Next and Finish to complete driver installation.

To verify successful installation in Windows 2000:

1. Double click My Computer, Control Panel, System,

Hardware, and click Device Manager.

2. Click on the + (plus sign) in front of Ports (Com & LPT).

3. New Cyber port(s) should be listed.

Windows XP Driver Installation

Windows XP will automatically detect and install the correct

driver for the CyberSerial PCI and CyberParallel PCI boards.

For the rest of the Cyber PCI I/O boards, please follow the

instructions below:

1. At the Found New Hardware Wizard, choose Install from a

list or specific location (Advanced),and click Next.

2. Insert the Driver Installation diskette, check Include this

location in the search: and uncheck the other check box.

3. Type in A:\win2k and click Next.

4. At the next Window, Hardware Installation, click Continue

Anyway, then Finish.

5. Repeat steps 1-4 X* more times to complete driver installation.

* X = the number of ports on the board

To verify successful installation in Windows XP:

1. Right click My Computer, click Manage, then select Device

Manager.

2. Click on the + (plus sign) in front of Ports (Com & LPT).

3. New Cyber port(s) should be listed.

DOS/Windows 3.1x Driver Installation

1. Insert the Driver Installation diskette, from the C: prompt,

type in copy a:\dos\*.*, then press <Enter>.

2. Type in edit autoexec.bat, then press <Enter>.

3. Add C:\CB20XPC.exe at the bottom of the autoexec.bat file.

4. Go to File, save the changes and exit.

5. Remove the diskette and restart the system for the new setup

to take effect.

Troubleshooting

Problem:Iaminstalling aparallelport(s) andmysystemfreezesup

when Windows tries to install the driver for my printer port.

Solution: Enter your system bios, set the onboard parallel port I/O

address to 278h, save and exit. In certain systems, the address 278h

is reserved for ISA boards. So when the PCI parallel port tries to

capture this address, your system gets confused and freezes up.

Technical Support

QUESTIONS? SIIG’s Online Support has the answers! Simply

visit our web site at www.siig.com and click on SUPPORT. Our

online support database is updated daily with new drivers and

solutions. Theanswerstoyourproblems could be justafewclicks

away.

Return Merchandise Authorization (RMA)

SIIGwarrantstotheoriginalbuyeroftheproductthatthehardware

isfreeofdefectsinmaterialsandworkmanshipforaperiodofone,

twoorfiveyears from thedateofpurchase.If your productfailsto

be in good working order during the warranty period, you may

return it to SIIG for repair or replacement at SIIG's option.

To return the product, you need to follow these steps.

Step 1: Contact SIIG's RMA Department

ToobtainanRMAnumber,SIIG'sRMADepartmentcanbereached

by phone at (510)413-5333 or fax at (510)657-5962 or email at

[email protected]. In order to issue an RMA number, the product

serialnumberisrequired. Thisnumbercanbefoundonthesideof

the box and on the back of the product.

Step 2: Complete the RMA form

• FilloutyourReturnMerchandiseAuthorization(RMA)form,and

include it in the package with the product.

• Properlypacktheproductforshipping. Allsoftware,cable(s)and

other accessories that came with the original package must be

included.

• ClearlywriteyourRMAnumberonthetopofthereturnedpackage

and on the accompanying RMA form.

SIIGwillrefusetoacceptanyshippingpackage,andwillnot

beresponsibleforaproductreturnedwithoutanRMAnumber

posted on the outside of the shipping carton.

Step 3: Ship the Product

You are responsible for the cost of shipping back to SIIG at the

following address:

SIIG, Inc. RMA#_______________

6078 Stewart Ave.

Fremont, CA 94538

SIIGwillshipthe repairedorreplacedproductvia UPSGroundor

US Mail at no cost to you.

PRODUCT NAME MODEL NUMBER

Cyber PCI I/O IO18xx

FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B

OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE

FCC COMPLIANCE STATEMENT:

This device complies with part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

FCC NOTICE:

This equipment has been tested and found to comply with the limits for a

ClassBdigitaldevice, pursuanttopart15 oftheFCC Rules.Theselimitsare

designed to provide reasonable protection against harmful interference in a

residentialinstallation.Thisequipmentgenerates,uses,andcanradiateradio

frequency energy and if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However,thereisnoguaranteethatinterferencewillnotoccurinaparticular

installation. If this equipment does cause harmful interference to radio and

television reception, which can be determined by turning the equipment off

andon,theuserisencouragedtotrytocorrecttheinterferencebyoneormore

of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected

• Consult the dealer or an experienced radio or TV technician for help

Caution:

Any changes or modifications not expressly approved by the party

responsibleforcompliancecouldvoidtheuser'sauthoritytooperate

this equipment

THE PARTY RESPONSIBLE FOR

PRODUCT COMPLIANCE

SIIG, Inc.

6078 Stewart Ave.

Fremont, CA 94538-3152

SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft, Windows and Windows

NT are registered trademarks of Microsoft Corporation. Pentium is a registered trademark of

Intel Corporation. Other names used in publication are for identification only and may be

trademarks of their respective companies.

Table des matières

Autres manuels SIIG Matériel informatique

SIIG

SIIG DP FireWire 800 3-Port PCIe Manuel utilisateur

SIIG

SIIG JU-91RW12-S4 Manuel utilisateur

SIIG

SIIG CE-H23J11-S1 Manuel utilisateur

SIIG

SIIG CyberParallel Dual Manuel utilisateur

SIIG

SIIG ExpressCard/54 CF R/W Manuel utilisateur

SIIG

SIIG UltraATA 133 PCI Manuel utilisateur

SIIG

SIIG SC-SAEE12-S1 Manuel utilisateur

SIIG

SIIG FireWire 800 2-Port ExpressCard/34 Manuel utilisateur

SIIG

SIIG IO1037 Manuel utilisateur

SIIG

SIIG Cyber I/O PCI Manuel utilisateur

SIIG

SIIG JJ-E01111-S1 Manuel utilisateur

SIIG

SIIG UltraATA 133 PCI Manuel utilisateur

SIIG

SIIG NN-000032-S1 Manuel utilisateur

SIIG

SIIG eSATA II PCIe i/e Manuel utilisateur

SIIG

SIIG JJ-EC1012-S1 Manuel utilisateur

SIIG

SIIG Silent Mini Notebook Cooler Manuel utilisateur

SIIG

SIIG NN-EC2822-S1 Manuel utilisateur

SIIG

SIIG UltraATA 133 PCI Manuel utilisateur

SIIG

SIIG FireWire 800 ExpressCard Manuel utilisateur

SIIG

SIIG DP SoundWave 4 Channel PCI Manuel utilisateur

SIIG

SIIG PCIe to ExpressCard Bay Manuel utilisateur

SIIG

SIIG ExpressCard/54 CF R/W Manuel utilisateur

SIIG

SIIG DP FireWire 800 PCIe Manuel utilisateur

SIIG

SIIG Low Profile POS 2000RJ Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur