Siemens SITRANS P220 Guide de l'administrateur

English ............................................................................................... 3

Deutsch............................................................................................ 20

Français ........................................................................................... 37

A5E03304437-AA, 09/2017 3

SITRANS

Pressure transmitter

SITRANS P220 (7MF1567)

Compact Operating Instructions

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The

notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage

have no safety alert symbol. These notices shown below are graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of

injury to persons with a safety alert symbol may also include a warning relating to property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific task in accordance with

the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their

training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products

and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage,

installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any

problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed.

Introduction

1.1

Purpose of this documentation

These instructions contain all information required to commission and use the device. Read the instructions carefully prior to

installation and commissioning. In order to use the device correctly, first review its principle of operation.

The instructions are aimed at persons mechanically installing the device, connecting it electronically, configuring the

parameters and commissioning it, as well as service and maintenance engineers.

See also

Technical support (Page 18)

SITRANS P220 (7MF1567)

4A5E03304437-AA, 09/2017

1.2

Checking the consignment

1. Check the packaging and the delivered items for visible damage.

2. Report any claims for damages immediately to the shipping company.

3. Retain damaged parts for clarification.

4. Check the scope of delivery by comparing your order to the shipping documents for correctness and completeness.

WARNING

Using a damaged or incomplete device

Risk of explosion in hazardous areas.

•

Do not use damaged or incomplete devices.

1.3

Transportation and storage

To guarantee sufficient protection during transport and storage, observe the following:

●Keep the original packaging for subsequent transportation.

●Devices/replacement parts should be returned in their original packaging.

●If the original packaging is no longer available, ensure that all shipments are properly packaged to provide sufficient

protection during transport. Siemens cannot assume liability for any costs associated with transportation damages.

NOTICE

Insufficient protection during storage

The packaging only provides limited protection against moisture and infiltration.

•

Provide additional packaging as necessary.

Special conditions for storage and transportation of the device are listed in Technical specifications (Page 14).

1.4

Notes on warranty

The contents of this manual shall not become part of or modify any prior or existing agreement, commitment or legal

relationship. The sales contract contains all obligations on the part of Siemens as well as the complete and solely applicable

warranty conditions. Any statements regarding device versions described in the manual do not create new warranties or

modify the existing warranty.

The content reflects the technical status at the time of publishing. Siemens reserves the right to make technical changes in

the course of further development.

Safety instructions

2.1

Prerequisites for safe use

This device left the factory in good working condition. In order to maintain this status and to ensure safe operation of the

device, observe these instructions and all the specifications relevant to safety.

Observe the information and symbols on the device. Do not remove any information or symbols from the device. Always

keep the information and symbols in a completely legible state.

Symbol

Explanation

Consult operating instructions

SITRANS P220 (7MF1567)

A5E03304437-AA, 09/2017 5

2.1.1

Laws and directives

Observe the safety rules, provisions and laws applicable in your country during connection, assembly and operation. These

include, for example:

●National Electrical Code (NEC - NFPA 70) (USA)

●Canadian Electrical Code (CEC) (Canada)

Further provisions for hazardous area applications are for example:

●IEC 60079-14 (international)

●EN 60079-14 (EC)

2.1.2

Conformity with European directives

The CE mark on the device is a sign of conformity with the following European directives:

Electromagnetic compatibility EMC

2014/30/EU

Directive o

f the European Parliament and of the Council on the harmonisation of the

laws of the Member States relating to electromagnetic compatibility.

Atmosphère explosible ATEX

2014/34/EU

Directive of the European Parliament and of the Council on the harmonisati

on of the

laws of the Member States relating to equipment and protective systems intended for

use in potentially explosive atmospheres.

The standards applied can be found in the EC declaration of conformity for the device.

WARNING

Improper device modifications

Risk to personnel, system and environment can result from modifications to the device, particularly in hazardous areas.

•Only carry out modifications that are described in the instructions for the device. Failure to observe this requirement

cancels the manufacturer's warranty and the product approvals.

2.2

Requirements for special applications

Due to the large number of possible applications, each detail of the described device versions for each possible scenario

during commissioning, operation, maintenance or operation in systems cannot be considered in the instructions. If you need

additional information not covered by these instructions, contact your local Siemens office or company representative.

Note

Operation under special ambient conditions

We highly recommend that you contact your Siemens representative or our application department before you operate the

device under special ambient conditions as can be encountered in nuclear power plants or when the device is used for

research and developm

ent purposes.

2.3

Use in hazardous areas

Qualified personnel for hazardous area applications

Persons who install, connect, commission, operate, and service the device in a hazardous area must have the following

specific qualifications:

●They are authorized, trained or instructed in operating and maintaining devices and systems according to the safety

regulations for electrical circuits, high pressures, aggressive, and hazardous media.

●They are authorized, trained, or instructed in carrying out work on electrical circuits for hazardous systems.

●They are trained or instructed in maintenance and use of appropriate safety equipment according to the pertinent safety

regulations.

SITRANS P220 (7MF1567)

6A5E03304437-AA, 09/2017

WARNING

Use in hazardous areas

Risk of explosion.

•Only use equipment that is approved for use in the intended hazardous area and labelled accordingly.

See also

Technical specifications (Page 14)

WARNING

Loss of safety of device with type of protection "Intrinsic safety Ex i"

If the device has already been operated in non-intrinsically safe circuits or the electrical specifications have not been

observed, the safety of the device is no longer ensured for use in hazardous areas. There is a risk of explosion.

•Connect the device with type of protection "Intrinsic safety" solely to an intrinsically safe circuit.

•Observe the specifications for the electrical data on the certificate and/or in Technical specifications (Page 14).

Description

3.1

Application

The pressure transmitter P220, Type 7MF1567, is used for measuring the relative pressure and absolute pressure of gases

and liquids in the following industrial areas:

●Mechanical engineering

●Power engineering

●Water supply

●Shipbuilding

●Chemical industry

●Pharmaceuticals

3.2

Hardware configuration

7MF1567 with plug complying with EN 175301-803-A

•

Type 7MF1567-*****-1**1

•

Type 7MF1567-*****-5**1

7MF1567 with plug M12x1

•

Type 7MF1567-*****-2**1

SITRANS P220 (7MF1567)

A5E03304437-AA, 09/2017 7

7MF1567 with cable (2 m)

•

Type 7MF1567-*****-3**1

7MF1567 with fast-fit cable gland

•

Type 7MF1567-*****-4**1

Device structure without explosion protection

The pressure transmitter consists of a piezo-resistive measuring cell with a diaphragm installed in a stainless steel

enclosure. It can be electrically connected using a plug complying with EN 175301-803-A (IP65), a round plug M12 (IP67), a

cable (IP67) or a fast-fit cable gland (IP67). The output signal is between 4 and 20 mA or 0 and 10 V.

Device structure with explosion protection

The pressure transmitter consists of a piezo-resistive measuring cell with a diaphragm installed in a stainless steel

enclosure. It can be connected electrically with a connector fulfilling EN 175301-803-A (IP65) or a round plug M12 (IP67).

The output signal amounts to between 4 and 20 mA.

3.3

Layout of the nameplate

*) Decoding for year, month and day information

Code

Year

2010

2011

2012

2013

2014

2015

H (G)

2016

2017

SITRANS P220 (7MF1567)

8A5E03304437-AA, 09/2017

Code

Year

2018

2019

2020

2021

2022

2023

2024

2025

2026

2027

2028

2029

Code

Month

January

February

March

April

May

June

July

August

September

October

November

December

Code

01-31

Day of month

1st to 31st day

1) Conforming to DIN EN 60062

2) The letter G is not permitted for new applications since it deviates from DIN EN 60062. It serves only for coding back.

Installing/mounting

4.1

Basic safety instructions

CAUTION

Direct sunlight

Device damage.

The device can overheat or materials become brittle due to UV exposure.

•Protect the device from direct sunlight.

•Make sure that the maximum permissible ambient temperature is not exceeded. Refer to the information in Technical

specifications (Page 14).

SITRANS P220 (7MF1567)

A5E03304437-AA, 09/2017 9

WARNING

Wetted parts unsuitable for the process media

Risk of injury or damage to device.

Hot, toxic and corrosive media could be released if the process medium is unsuitable for the wetted parts.

•Ensure that the material of the device parts wetted by the process medium is suitable for the medium. Refer to the

information in Technical specifications (Page 14).

Note

Material compatibility

Siemens can provide you with support concerning selection of sensor components wetted by process media. However, you

are responsible for the selection of components. Siemens accepts no liability for faults or failures resulting from incompatible

materials.

WARNING

Exceeded maximum ambient or process media temperature

Danger of explosion in hazardous areas.

Device damage.

•Make sure that the maximum permissible ambient and process media temperatures of the device are not exceeded.

Refer to the information in Technical specifications (Page 14).

4.2

Additional notes on installation of explosion protection devices

The following specifications are to be observed for the types

7MF1567-***01-1**1

7MF1567-***01-2**1

, and

7MF1567-

***01-5**1

Operation is permitted only when connected to certified intrinsically-safe resistive circuits with the following maximum values:

≤30 V

≤100 mA

Pi≤750 mW

Internal inductance Li = 0 nH

Internal capacitance Ci = 0 nF

A maximum ambient air temperature Taof -25 °C to +85 ºC is permitted for the pressure transmitter.

Use as a resource belonging to Category 1/2:

The pressure transmitters can be mounted in the wall separating the area with Category 1 requirements (Zone 0) and the

area with Category 2 requirements (Zone 1). In this case, the process connection must be adequately sealed in compliance

with IEC/EN 60079-26, Clause 4.3, for example by providing degree of protection IP67 in compliance with EN60529. The

supply must be effected via intrinsically safe circuits with type of protection ia. The measuring cell may only be used for

flammable materials to which the diaphragms of the measuring cells are adequately resistant both chemically and in terms of

corrosion.

4.3

Installation

●The location of the device has no influence on the measurement accuracy.

●Before installation, compare the process data with the data of the rating plate.

●The medium being measured must be suitable for the parts of the pressure transmitter in contact with the medium.

●The overload limit must not be exceeded.

●Connect the devices with fixed cable installation.

SITRANS P220 (7MF1567)

10 A5E03304437-AA, 09/2017

Connecting

5.1

Basic safety instructions

WARNING

Unsuitable cables, cable glands and / plug-in connectors

Danger of explosion in hazardous areas.

•Only use cable glands/plug-in connectors that fulfill the requirements of the relevant type of protection.

•Only use cables that have been designed for an ambient temperature of at least 20 K higher.

•Close cable openings for electrical connections that are unused.

•When replacing cable glands, only use ones of the same type.

•

After installation check that the cables are seated firmly.

WARNING

Improper power supply

Risk of explosion in hazardous areas as result of incorrect power supply, e.g. using direct current instead of alternating

current.

•Connect the device in accordance with the specified power supply and signal circuits. The relevant specifications can

be found in the certificates, in Technical specifications (Page 14) or on the nameplate.

WARNING

Unsafe extra-low voltage

Risk of explosion in hazardous areas due to voltage flashover.

•

Connect the device to an extra-low voltage with safe isolation (SELV).

5.1.1

Grounding for Ex (explosion protection) devices

WARNING

Lack of equipotential bonding

Danger of explosion through compensating currents or ignition currents through lack of equipotential bonding.

•Make sure that equipotential bonding exists for the device.

•The pressure transmitter must be connected to the equipotential bonding system of the plant via the metal housing

(process connection) or the ground conductor of the plug.

Exception:

It may be permissible to omit connection of the equipotential bonding for devices with type of protection

"Intrinsic safety Ex i".

WARNING

Unprotected cable ends

Risk of explosion through unprotected cable ends in hazardous areas.

•

Protect unused cable ends in accordance with IEC/EN 60079-14.

Autres manuels pour SITRANS P220

Table des matières

Langues :

Autres manuels Siemens Émetteur

Siemens

Siemens 7ML5431 Manuel utilisateur

Siemens

Siemens SITRANS L Series Manuel utilisateur

Siemens

Siemens sitrans lc 300 Manuel d'instructions

Siemens

Siemens Sitrans LR250 Guide de l'administrateur

Siemens

Siemens Sitrans LR200 Manuel d'instructions

Siemens

Siemens SITRANS TK Manuel utilisateur

Siemens

Siemens SITRANS P 7MF1562 Manuel utilisateur

Siemens

Siemens 8DJH Manuel

Siemens

Siemens SITRANS P200 Manuel utilisateur

Siemens

Siemens SITRANS L Manuel utilisateur

Siemens

Siemens Sitrans LR250 Manuel utilisateur

Siemens

Siemens SITRANS P series Guide de l'administrateur

Siemens

Siemens SITRANS 7MF1570 Manuel utilisateur

Siemens

Siemens SITRANS P500 Guide de l'administrateur

Siemens

Siemens SITRANS LR560 Guide de l'administrateur

Siemens

Siemens SITRANS P500 Manuel utilisateur

Siemens

Siemens SITRANS LR260 Manuel d'instructions

Siemens

Siemens SITRANS LR560 Manuel d'instructions

Siemens

Siemens SITRANS LR110 Manuel utilisateur

Siemens

Siemens 7ML5202 Manuel utilisateur

Siemens

Siemens SITRANS T Series Manuel utilisateur

Siemens

Siemens SITRANS P500 Guide de l'administrateur

Siemens

Siemens sitrans tr200 Manuel utilisateur

Siemens

Siemens SITRANS P Manuel utilisateur

Manuels Émetteur populaires d'autres marques

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuel du propriétaire

Honeywell

Honeywell 5816WMBR Manuel utilisateur

Kamstrup

Kamstrup READy MTU Mode d'emploi

Omega

Omega ZW Series Manuel utilisateur

ABB

ABB Field 264H Mode d’emploi

Alinco

Alinco DJ-V17T Manuel utilisateur

Dejero

Dejero EnGo 3x Manuel utilisateur

Rosemount

Rosemount 4600 Manuel utilisateur

Speaka Professional

Speaka Professional 2342740 Manuel utilisateur

trubomat

trubomat GAB 1000 Manuel utilisateur

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuel utilisateur

Rondish

Rondish UT-11 Manuel utilisateur

MG 10JRE Manuel utilisateur

Burkert

Burkert 8177 Manuel utilisateur

Firetide

Firetide HotPort 3203 Manuel

Tele Radio

Tele Radio T9-02 Manuel utilisateur

Rotronic

Rotronic HygroFlex HF3 Series Manuel utilisateur

Jamara

Jamara FCX6 Pro Tel Manuel utilisateur