Siemens SINAMICS G130 Manuel utilisateur
Operating Instructions · 03/2013
Line reactors
SINAMICS G130
SINAMICS
s
Line reactors
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
_
_________________
_
SINAMICS
SINAMICS G130
Line reactors
Operating Instructions
Control version V4.6
03/2013
A5E00331462A
Safety information
1
General
2
Mechanical installation
3
Electrical installation
4
Technical specifications
5
Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E00331462A
Ⓟ 05/2013 Technical data subject to change
Copyright © Siemens AG 2004 - 2013.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Line reactors
Operating Instructions, 03/2013, A5E00331462A 3
Table of contents
1 Safety information...................................................................................................................................... 5
1.1 Warnings........................................................................................................................................5
1.2 Safety and application instructions ................................................................................................6
2 General...................................................................................................................................................... 7
3 Mechanical installation............................................................................................................................... 9
4 Electrical installation ................................................................................................................................ 13
5 Technical specifications........................................................................................................................... 15
Table of contents
Line reactors
4 Operating Instructions, 03/2013, A5E00331462A
Line reactors
Operating Instructions, 03/2013, A5E00331462A 5
Safety information 1
1.1 Warnings
WARNING
Dangerous electrical voltage
Hazardous voltages are present when electrical equipment is in operation.
Severe personal injury or substantial material damage may result if these warnings are not
observed.
Only qualified personnel are permitted to work on or around the equipment.
These personnel must be thoroughly familiar with all the warnings and maintenance
procedures described in these operating instructions.
The successful and safe operation of this device is dependent on correct transport, proper
storage and installation, as well as careful operation and maintenance.
National safety guidelines must be observed.
DANGER
Five safety rules
When carrying out any kind of work on electrical devices, the "five safety rules" according to
EN 50110 must always be observed:
1. Disconnect the system.
2. Protect against reconnection.
3. Make sure that the equipment is de-energized.
4. Ground and short-circuit.
5. Cover or enclose adjacent components that are still live.
Note
Use of copper cables for a UL-approved system
For a UL-approved system use 60/75°C copper conductors only.
Safety information
1.2 Safety and application instructions
Line reactors
6 Operating Instructions, 03/2013, A5E00331462A
1.2 Safety and application instructions
DANGER
Dangerous electrical voltage
This equipment is used in industrial high-voltage installations. During operation, this
equipment contains live, bare parts. For this reason, they could cause severe injury or
significant material damage if the required covers are removed, if they are used or operated
incorrectly, or have not been properly maintained.
When the machines are used in non-industrial areas, the installation location must be
protected against unauthorized access (protective fencing, appropriate signs).
Preconditions
The persons responsible for the safety of the plant must ensure that the following conditions
are met:
● Basic planning work for the system and all work relating to transportation, assembly,
installation, commissioning, maintenance and repairs is carried out by qualified personnel
and checked by responsible, suitably skilled personnel.
● The Operating Instructions and machine documentation are always available.
● The technical specifications regarding the applicable installation, connection,
environmental, and operating conditions are always observed.
● The plant-specific assembly and safety guidelines are observed and personal protection
equipment is used.
● Unqualified personnel are forbidden from using these machines and working near them.
These Operating Instructions are intended for qualified personnel and only contain
information and notes relating to the intended purpose of the machines.
The Operating Instructions and machine documentation are written in different languages as
specified in the delivery contracts.
Note
Support by SIEMENS service centers
We recommend engaging the support and services of your local Siemens service center for
all planning, installation, commissioning and maintenance work.
Line reactors
Operating Instructions, 03/2013, A5E00331462A 7
General 2
Description
Line reactors limit low-frequency line-side harmonics to permissible values.
NOTICE
Maintain ventilation clearances
The 100 mm cooling clearances above and to the side of the components must be
observed.
Note
Cable lengths
The connecting cables to the Power Module must be kept as short as possible.
NOTICE
Use only approved line reactors
When using line reactors that have not been approved by SIEMENS for SINAMICS, the
following can occur:
The Power Modules could be damaged/destroyed.
Line harmonics may interfere with or damage other loads connected to the same line
supply.
CAUTION
Hot surfaces
The surface temperature of the line reactors may exceed 80 °C.
NOTICE
Component cooling
Provisions for component cooling must be made at the installation site. Power loss data is
given in the technical specifications.
General
Line reactors
8 Operating Instructions, 03/2013, A5E00331462A
Assignment of line reactor and Power Module
Table 2- 1 Assignment of line reactor and Power Module
Power Module Unit rating of the Power Module Suitable line reactor
Line voltage 380 – 480 V 3 AC
6SL3310-1GE32-1AAx 110 kW 6SL3000-0CE32-3AA0
6SL3310-1GE32-6AAx 132 kW 6SL3000-0CE32-8AA0
6SL3310-1GE33-1AAx 160 kW 6SL3000-0CE33-3AA0
6SL3310-1GE33-8AAx 200 kW 6SL3000-0CE35-1AA0
6SL3310-1GE35-0AAx 250 kW 6SL3000-0CE35-1AA0
6SL3310-1GE36-1AAx 315 kW 6SL3000-0CE36-3AA0
6SL3310-1GE37-5AAx 400 kW 6SL3000-0CE37-7AA0
6SL3310-1GE38-4AAx 450 kW 6SL3000-0CE38-7AA0
6SL3310-1GE41-0AAx 560 kW 6SL3000-0CE41-0AA0
Line voltage 500 – 600 V 3 AC
6SL3310-1GF31-8AAx 110 kW 6SL3000-0CH32-2AA0
6SL3310-1GF32-2AAx 132 kW 6SL3000-0CH32-2AA0
6SL3310-1GF32-6AAx 160 kW 6SL3000-0CH32-7AA0
6SL3310-1GF33-3AAx 200 kW 6SL3000-0CH33-4AA0
6SL3310-1GF34-1AAx 250 kW 6SL3000-0CH34-8AA0
6SL3310-1GF34-7AAx 315 kW 6SL3000-0CH34-8AA0
6SL3310-1GF35-8AAx 400 kW 6SL3000-0CH36-0AA0
6SL3310-1GF37-4AAx 500 kW 6SL3000-0CH38-4AA0
6SL3310-1GF38-1AAx 560 kW 6SL3000-0CH38-4AA0
Line voltage 660 – 690 V 3 AC
6SL3310-1GH28-5AAx 85 kW 6SL3000-0CH31-1AA0
6SL3310-1GH31-0AAx 90 kW 6SL3000-0CH31-1AA0
6SL3310-1GH31-2AAx 110 kW 6SL3000-0CH31-6AA0
6SL3310-1GH31-5AAx 132 kW 6SL3000-0CH31-6AA0
6SL3310-1GH31-8AAx 160 kW 6SL3000-0CH32-2AA0
6SL3310-1GH32-2AAx 200 kW 6SL3000-0CH32-2AA0
6SL3310-1GH32-6AAx 250 kW 6SL3000-0CH32-7AA0
6SL3310-1GH33-3AAx 315 kW 6SL3000-0CH33-4AA0
6SL3310-1GH34-1AAx 400 kW 6SL3000-0CH34-8AA0
6SL3310-1GH34-7AAx 450 kW 6SL3000-0CH34-8AA0
6SL3310-1GH35-8AAx 560 kW 6SL3000-0CH36-0AA0
6SL3310-1GH37-4AAx 710 kW 6SL3000-0CH38-4AA0
6SL3310-1GH38-1AAx 800 kW 6SL3000-0CH38-4AA0
Autres manuels pour SINAMICS G130
33
Table des matières
Autres manuels Siemens Unité de contrôle
Siemens
Siemens XC1003-A Mode d’emploi
Siemens
Siemens SIMATIC FM 351 Manuel utilisateur
Siemens
Siemens VAG60 Series Manuel utilisateur
Siemens
Siemens WF 705 Instructions d'utilisation et d'installation
Siemens
Siemens Simatic S7-1500 Manuel utilisateur
Siemens
Siemens ECOFAST 3RK1911-4AA Series Manuel utilisateur
Siemens
Siemens 7153 Manuel utilisateur
Siemens
Siemens SIMOTION Manuel de la liste des pièces
Siemens
Siemens SIMATIC NET CP 1243-1 DNP3 Feuille d'instructions
Siemens
Siemens SINUMERIK 840D sl Guide de démarrage rapide
Siemens
Siemens Q3920 Manuel utilisateur
Siemens
Siemens SINAMICS G130 Manuel utilisateur
Siemens
Siemens Simatic 6ES7132-4HB01-0AB0 Manuel utilisateur
Siemens
Siemens ASR61EX Manuel utilisateur
Siemens
Siemens SITRANS FM MAG 8000 IIoT Manuel utilisateur
Siemens
Siemens SINAMICS G120 Manuel utilisateur
Siemens
Siemens NCU 7x0.3 PN Series Manuel utilisateur
Siemens
Siemens IONPURE VNX50HH-2 Manuel
Siemens
Siemens SIMATIC ET 200SP Manuel utilisateur
Siemens
Siemens Simatic S7-1500 Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
