Siemens SIMATIC S7 3964 Manuel d'instructions

Siemens AG

SIMATIC S7 3964(R)/

RK512 Driver

1 System Configuration.......................................................................................................3

2 Selection of External Device............................................................................................4

3 Example of Communication Setting.................................................................................5

4 Setup Items....................................................................................................................11

5 Cable Diagram...............................................................................................................16

6 Supported Device...........................................................................................................18

7 Device Code and Address Code....................................................................................19

8 Error Messages..............................................................................................................20

SIMATIC S7 3964(R)/RK512 Driver

GP-Pro EX Device/PLC Connection Manual 2

Introduction

This manual describes how to connect the Display (GP3000 series) and the External Device (target PLC).

In this manual, the connection procedure will be described by following the below sections:

1System Configuration

This section shows the types of External

Devices which can be connected and SIO

type.

)"1 System Configuration" (page 3)

2Selection of External Device

Select a model (series) of External Device

to be connected and connection method.

)"2 Selection of External Device" (page 4)

3Example of Communication Settings

This section shows setting examples for

communicating between the Display and

the External Device.

)"3 Example of Communication Setting" (page

4Setup Items

This section describes communication

setup items on the Display.

Set communication settings of the Display

with GP-Pro EX or in off-line mode.

)"4 Setup Items" (page 11)

5Cable Diagram

This section shows cables and adapters

for connecting the Display and the

External Device.

)"5 Cable Diagram" (page 16)

Operation

SIMATIC S7 3964(R)/RK512 Driver

GP-Pro EX Device/PLC Connection Manual 3

1 System Configuration

The system configuration in the case when the External Device of Siemens AG and the Display are connected is

shown.

Series CPU Module Link I/F SIO Type Setting Example Cable Diagram

SIMATIC

S7-300 Series

CPU312IFM

CPU313

CPU314

CPU314IFM

CPU315

CPU315-2 DP

CPU316

CPU316-2 DP

CPU318-2

CP341

(RS232C) RS232C Setting Example 1

(page 5) Cable Diagram 1

(page 16)

CP341

(RS422/485) RS422/485

(4wire) Setting Example 2

(page 8) Cable Diagram 2

(page 17)

SIMATIC

S7-400 Series

CPU412-1

CPU412-2 DP

CPU413-1

CPU413-2 DP

CPU414-1

CPU414-2 DP

CPU414-3 DP

CPU416-1

CPU416-2 DP

CPU416-3 DP

CPU417-4

CP441-2

RS232C Setting Example 1

(page 5) Cable Diagram 1

(page 16)

RS422/485

(4wire) Setting Example 2

(page 8) Cable Diagram 2

(page 17)

SIMATIC S7 3964(R)/RK512 Driver

GP-Pro EX Device/PLC Connection Manual 4

2 Selection of External Device

Select the External Device to be connected to the Display.

Setup Items Setup Description

Maker Select the maker of the External Device to be connected. Select "Siemens AG".

Driver

Select a model (series) of the External Device to be connected and connection method.

Select "SIMATIC S7 3964(R)/RK512".

Check the External Device which can be connected in "SIMATIC S7 3964(R)/RK512" in

system configuration.

)"1 System Configuration" (page 3)

Use System Area

Check this option when you synchronize the system data area of the Display and the device

(memory) of the External Device. When synchronized, you can use the ladder program of

the External Device to switch the display or display the window on the Display.

Cf. GP-Pro EX Reference Manual "Appendix 1.4 LS Area (only for direct

access method)"

This can be also set with GP-Pro EX or in off-line mode of the Display.

Cf. GP-Pro EX Reference Manual "System Area Setting, 6.13.6 Setting Guide

of [System Setting Window]"

Cf. GP3000 Series User Manual "4.3.6 System Area Setting"

Port Select the Display port to be connected to the External Device.

SIMATIC S7 3964(R)/RK512 Driver

GP-Pro EX Device/PLC Connection Manual 5

3 Example of Communication Setting

Examples of communication settings of the Display and the External Device, recommended by Pro-face, are

shown.

3.1 Setting Example 1

Setting of GP-Pro EX

Communication Settings

To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.

Device Setting

To display the setting screen, click ([Setting]) of External Device you want to set from [Device-Specific

Settings] of [Device/PLC Settings].

When [Allowable No. of Device/PLCs] is multiple, you can click from [Device-Specific Settings] of

[Device/PLC Settings] to add External Device which is available to set.

SIMATIC S7 3964(R)/RK512 Driver

GP-Pro EX Device/PLC Connection Manual 6

Settings of External Device

(1) Startup "SIMATIC Manager" and create the new project. Set the optional project name and click [OK]. New

project is created.

(2) From the menu bar, select [Insert], [Station], [Name of CPU type to use] (ex: [1 SIMATIC 400 Station]) in this

order.

(3) [(Name of CPU type to use)] (ex: [SIMATIC 400 (1)]) is created in the project. Double-click [Hardware] of

the name of CPU type to use.

(4) When the [HW Config] screen displayed, open [(Name of CPU type to use)], [(RACK type to use)] (ex:

[SIMATIC 400], [RACK-400]) in this order from the left tree and select the base unit of the using model.

(5) Drag & drop the selected base unit to the upper right window. The rack figure is created in the window.

(6) Drag & drop the using power unit in the rack.

(7) Similarly, drag & drop the using CPU unit.

(8) When using CPUxxx-xDP, the [Properties - PROFIBUS interface DP] dialog box is displayed. In that case,

click [Cancel] and close the dialog box.

(9) Similarly, drag & drop the using link unit.

(10)Double-click the CPU unit dropped in the rack.

(11)When the [MPI port] setting dialog box is displayed, click [Properties].

(12)Click [Properties] as "MPI(1) 187.5 Kbps" is selected as default. The value entered in [Address] this time

becomes the Destination Node No. (PLC Address) you set in GP-Pro EX. The default is "2".

(13)To change the speed [Transmission rate] and the highest value of the node No. [Highest MPI address], click

the [Network Settings] tab.

Select [187.5Kbps] for [Transmission rate]. To change the highest value of the node No. (Highest MPI

address), check [Change] to allow you to select from the list.

(14)When you finish setting, click [OK] and close the dialog box.

(15)Close other dialog boxes similarly.

SIMATIC S7 3964(R)/RK512 Driver

GP-Pro EX Device/PLC Connection Manual 7

(16)Select [(Name of CPU type to use)] in the project, and open [Blocks] in the program, then double-click

[OB1].

(17)Here, you need to arrange the ladder program. Sample ladder program is shown below.

(18)Next, double-click [Hardware] in the CPU.

(19)Double-click the link unit as the link unit to use is already registered by the previous operation.

(20)To enable the communication between the External Device and the Display, click the [Parameter] button.

(21)The Parameter window is displayed. Select [RK512] from the [Protocol] list box and double-click the

[Protocol] image in the window.

(22)When the [Protocol] dialog box is displayed, set in the [RK 512] tab as below.

(23)When you finish setting, click [OK] and close the dialog box.

Setup Items Setup Description

With Block Check Check

Use Default Values Check

Transmission Rate 9600 bps

Stop Bits 1

Parity Even

Priority Low

SIMATIC S7 3964(R)/RK512 Driver

GP-Pro EX Device/PLC Connection Manual 8

3.2 Setting Example 2

Setting of GP-Pro EX

Communication Settings

To display the setting screen, select [Device/PLC Settings] from [System setting window] in workspace.

Device Setting

To display the setting screen, click ([Setting]) of External Device you want to set from [Device-Specific

Settings] of [Device/PLC Settings].

When [Allowable No. of Device/PLCs] is multiple, you can click from [Device-Specific Settings] of

[Device/PLC Settings] to add External Device which is available to set.

SIMATIC S7 3964(R)/RK512 Driver

GP-Pro EX Device/PLC Connection Manual 9

Settings of External Device

(1) Startup "SIMATIC Manager" and create the new project. Set the optional project name and click [OK]. New

project is created.

(2) From the menu bar, select [Insert], [Station], [(Name of CPU type to use)] in this order.

(3) [(Name of CPU type to use)] is created in the project. Double-click [Hardware] of the name of CPU type to

use.

(4) When the [HW Config] screen displayed, open [(Name of CPU type to use)], [(RACK type to use)] in this

order from the left tree and select the base unit of the using model.

(5) Drag & drop the selected base unit to the upper right window. The rack figure is created in the window.

(6) Drag & drop the using power unit in the rack.

(7) Similarly, drag & drop the using CPU unit.

(8) When using CPUxxx-xDP, the [Properties - PROFIBUS interface DP] dialog box is displayed. In that case,

click [Cancel] and close the dialog box.

(9) Similarly, drag & drop the using link unit.

(10)Double-click the CPU unit dropped in the rack.

(11)When the [MPI port] setting dialog box is displayed, click [Properties].

(12)Click [Properties] as "MPI(1) 187.5 Kbps" is selected as default. The value entered in [Address] this time

becomes the Destination Node No. (PLC Address) you set in GP-Pro EX. The default is "2".

(13)To change the speed [Transmission rate] and the highest value of the node No. [Highest MPI address], click

the [Network Settings] tab.

Select [187.5Kbps] for [Transmission rate]. To change the highest value of the node No. (Highest MPI

address), check [Change] to allow you to select from the list.

(14)When you finish setting, click [OK] and close the dialog box.

(15)Close other dialog boxes similarly.

SIMATIC S7 3964(R)/RK512 Driver

GP-Pro EX Device/PLC Connection Manual 10

(16)Select [(Name of CPU type to use)] in the project, and open [Blocks] in the program, then double-click

[OB1].

(17)Here, you need to arrange the ladder program. Sample ladder program is shown below.

(18)Next, double-click [Hardware] in the CPU.

(19)Double-click the link unit as the link unit to use is already registered by the previous operation.

(20)To enable the communication between the External Device and the Display, click the [Parameter] button.

(21)The Parameter window is displayed. Select [RK512] from the [Protocol] list box and double-click the

[Protocol] image in the window.

(22)When the [Protocol] dialog box is displayed, set in the [RK 512] tab as below.

(23)When connecting CP341/CP441 with RS422/485, double-click the [Interface] tab and select [None] in [Initial

State of the Receive Line].

(24)When you finish setting, click [OK] and close the dialog box.

Setup Items Setup Description

With Block Check Check

Use Default Values Check

Transmission Rate 9600 bps

Stop Bits 1

Parity Even

Priority Low

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Siemens Unité de contrôle

Siemens

Siemens EFB300 Manuel utilisateur

Siemens

Siemens SIRIUS ACT 3SU1400-1GC10-1AA0 Manuel utilisateur

Siemens

Siemens SIMOCODE pro 3UF7400-1AA00-0 Manuel utilisateur

Siemens

Siemens RUGGEDCOM ROS Manuel utilisateur

Siemens

Siemens SINAMICS DCM Manuel utilisateur

Siemens

Siemens SINUMERIK 808D Guide d'installation

Siemens

Siemens Simatic S7-1500 Manuel utilisateur

Siemens

Siemens PSO+ Manuel utilisateur

Siemens

Siemens SIMATIC TI505 386/ATM Manuel utilisateur

Siemens

Siemens RDM-MXL Manuel utilisateur

Siemens

Siemens VVI46 Series Manuel utilisateur

Siemens

Siemens Simatic Net Scalance M812 Manuel utilisateur

Siemens

Siemens WFZ661 Manuel d'installation et d'exploitation

Siemens

Siemens SINUMERIK 828D PPU Series Manuel utilisateur

Siemens

Siemens 986-88301A Manuel utilisateur

Siemens

Siemens FDK:085U0321 Manuel utilisateur

Siemens

Siemens SIMATIC 6ES7135-4MB02-0AB0 Manuel utilisateur

Siemens

Siemens FS-TRI-M Manuel utilisateur

Siemens

Siemens Flowrite 599 Series Manuel du propriétaire

Siemens

Siemens SINUMERIK 840D sl Manuel utilisateur

Siemens

Siemens CP 443-5 Extended Manuel utilisateur

Siemens

Siemens SIPROTEC 6MU805 Manuel utilisateur

Siemens

Siemens SPCW110 Manuel utilisateur

Siemens

Siemens SIPROTEC 7SJ80 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur