Siemens FCM-6S Manuel utilisateur

Siemens Industry, Inc.

Building Technologies Division

P/N 315-035800-2

INTRODUCTION The SIEMENS Models FCM-6S, LCM-8S and SCM-8S

are similar in appearance and identical in installation.

Models with the “S” suffix are gray in color.

The SIEMENS Model FCM-6S Control Module

(Figure 1) contains six sets of three pushbutton

switches and their corresponding LEDs. The ON and

AUTO switches both have one bi-color (red/green)

LED while the OFF switch has one bi-color and one

yellow LED. The functions of the switches and LEDs

are programmed using the Zeus Tool (Refer to the

Zeus Quick Start Guide, P/N 315-033875). All LEDs

can be programmed ON, OFF, or FLASHING. The

FCM is designed for general control requiring ON/

OFF/AUTO operation.

The SIEMENS Model LCM-8S LED Control Module

(Figure 2) contains eight pairs of LEDs. Each pair

contains one bi-color (red/green) and one yellow LED.

The functions of the LEDs are programmed using the

Zeus Tool (Refer to the Zeus Quick Start Guide, P/N

315-033875). All LEDs can be programmed ON, OFF,

or FLASHING. These LEDs are used for fire system

status annunciation.

The SIEMENS Model SCM-8S Switch Control

Module (Figure 3) contains eight switches and eight

pairs of LEDs. Each pair contains one bi-color (red/

green) and one yellow LED. The functions of the

switches and LEDs are programmed using the Zeus

Tool (Refer to the Zeus Quick Start Guide, P/N 315-

033875). All LEDs can be programmed ON, OFF, or

FLASHING. The SCM is used for manual control of

the fire system.

Figure 1

FCM-6S Control Module

Figure 2

LCM-8S LED Control

Module

Figure 3

SCM-8S Switch Control

Module

TRBL

TRBL TRBL

Control Module / LED Control Module / Switch Control Module

CAN Sounder Board

Installation Instructions

Models FCM-6S / LCM-8S / SCM-8S

Model CSB

Siemens Industry, Inc.

Building Technologies Division

P/N 315-035800-22

The SIEMENS Model CSB CAN Sounder Board

(P/N 500-033130) is an optional module that can be

ordered separately. It contains a sounder (buzzer) that

can be used with the SCM-8S or FCM-6S to provide

audible feedback to indicate that a switch closed

properly and communication was successful. The

CSB requires no programming.

All modules mount on the inner door of an enclosure.

OPERATION

FCM Controls and Indicators The FCM contains six sets of three pushbutton switches and their corresponding

LEDs. Pressing any of the six ON, OFF, or AUTO switches generates a unique CAN

message on the bus to the NIC that indicates which switch was pressed. A CAN

message from the NIC to the FCM produces a preprogrammed output to the corre-

sponding LED (ON, FLASHING, or OFF). An open collector is provided for connection

to the CAN Sounder Board (CSB), a separate audio module. The CSB provides an

audible feedback to indicate that the switch closed properly and that communication

between the FCM and NIC was successful.

LCM Controls and Indicators The LCM contains eight pairs of LEDs. A CAN message from the NIC to the LCM

produces a preprogrammed output to any of the corresponding LEDs (ON, FLASH-

ING, or OFF).

SCM Controls and Indicators The SCM contains eight switches and eight pairs of LEDs. Each switch is associated

with a pair of LEDs. Pressing of any of the eight switches generates a unique CAN

message on the bus to the NIC that indicates which switch was pressed. A CAN

message from the NIC to the SCM produces a preprogrammed output to the

corresponding LED (ON, FLASHING, or OFF). An open collector is provided for

connection to the CAN Sounder Board (CSB), a separate audio module. The CSB

provides an audible feedback to indicate that the switch closed properly and that

communication between the SCM and NIC was successful.

CSB Controls and Indicators The CSB contains a sounder (buzzer) that sounds when any switch on an FCM or

SCM is pressed. Only one CSB is required for audible feedback; more can be

connected to increase the volume if needed.

PRE-INSTALLATION Set the board address for each FCM/LCM/SCM using both of the ten-position rotary

switches located on the back of the board (See Figure 5). Each of these addresses

must be a sub-address of the NIC and must be the same as the addresses assigned

in the Zeus Programming Tool. The CSB does not require address setting.

After setting the address, label each switch or LED. When viewed from the front

panel of the FCM/LCM/SCM, the labels are on the left and the control switches and

LEDs are on the right.

• Refer to the Zeus configuration for the address of each module and its

assigned functions.

• Remove the label strip from its slot, and type or print a brief function

identifier for each switch.

• After completing the label strip, insert in back into its slot (See Figure 6).

Buzzer

Figure 4

CSB Sounder Board

Siemens Industry, Inc.

Building Technologies Division

P/N 315-035800-23

PLUG-IN

CABLE

CONNECTION

ROTARY

ADDRESS SWITCHES

Figure 5

FCM-6S, LCM-8S , SCM-8S Address Switches And

Cable Connections

INSTALLATION

CAN Sounder Board The CSB is normally positioned at the last FCM, LCM or SCM. If desired, multiple

CSBs can be installed. The CSB mounts on the stud of the FCM/LCM/SCM module

that it connects to.

1. Determine the position of the CSB. (This is normally at the last FCM, LCM

or SCM module.)

2. If necessary, remove nut from stud of FCM/LCM/SCM where CSB is to be

mounted.

2. Place mounting hole on the CSB over stud.

3. Secure with nut supplied with FCM/LCM/SCM.

WIRING (Refer to Figure 7.)

Remove ELECTRICAL POWER prior to working on equipment.

• Each FCM/LCM/SCM module is a node in the CAN bus.

• Each FCM/LCM/SCM connects through the CC-5/CC-2 CAN bus via a

plug-in cable to the NIC or to another FCM/LCM/SCM module.

• Up to 99 FCM/LCM/SCM modules, in any combination, can be connected

to the CAN bus of each NIC.

• Each FCM/LCM/SCM/CSB module is shipped with one CCS cable.

Figure 6

Inserting A Label Into The Back Of The FCM-6S

Siemens Industry, Inc.

Building Technologies Division

P/N 315-035800-24

• Cable connections for FCM/LCM/SCM/CSB modules are shown in the

following table and in Figure 8:

SNOITCENNOCELBACBSC/MCS/MCL/MCF

elbaCnoitpircseDrebmuNtraPnoitcennoC

LCCgnoL-ELBAC-NAC

rotcudnoc-6,.ni03

4124

36-995)roodno(worotwormorfstcennoC

.seludomBSC/MCS/MCL/MCFrof

2-CC/5-CCno3PmorfstcennocoslA

MCS/MCL/MCFts

rifot

SCCtrohS-ELBAC-NAC

rotcudnoc-6,.ni½5

935331-555BSC/MCS/MCL/MCFstcennoC

BSC/MCS/MCL/MCFotseludom

worelg

nisaniseludom

Figure 8

Typical Wiring For FCM-6S, LCM-8S , SCM-8S And CSB

Buzzer

TO CC-5/CC-2, P3

FCM-6S

CSB

LCM-8S

SCM-8S

LCM-8S

SCM-8S

LCM-8S

SCM-8S

LCM-8S

SCM-8S

LCM-8S

SCM-8S

LCM-8S

SCM-8S

LCM-8S

SCM-8S

LCM-8S

SCM-8S

LCM-8S

SCM-8S

LCM-8S

SCM-8S

LCM-8S

SCM-8S

LCM-8S

SCM-8S

INSTALL

CAN TERMINATOR

P/N C24235-A1-K2

(SHIPPED WITH DAC-NET)

CABLE

MODEL

# CCS

CABLE

MODEL

# CCL

Siemens Industry, Inc.

Building Technologies Division

P/N 315-035800-25

The CAN bus requires a 120Sresistance at each end of the loop. Refer to the

DAC-NET Installation Instructions, P/N 1A24205-A334-B839 for details about CAN

termination.

ELECTRICAL RATINGS

tnerruCenalPkcaBV420

tnerruCV42lanimreTwercS xamAm41

DELevitcarepAm1+

tnerruCenalPkcaBV2.60

tnerruCybdnatSV4

2xamAm41

DELevitcarepAm1+

SLOT 1

2019 21 20

SLOT 2

2423

17 19 2422

21 23

a c

E11/E5

a c

CC-5 / CC-2

SLOT 1

SLOT 2

16 9

TO PSC-12-C

TB4 +

TB4 -

CCL TO

FRONT

DOOR

(P/N 599-634214)

Figure 8

Connecting Power For FCM-6S, LCM-8S, SCM-8S Modules

Siemens Industry, Inc.

Building Technologies Division

P/N 315-035800-26

Siemens Industry, Inc.

Building Technologies Division

P/N 315-035800-27

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 Canada

P/N 315-035800-2

Siemens Gebäudesicherheit

GmbH & Co. oHG

D-80930 München

For CE applications in Cerberus E100 systems refer to

Installation Instruction A24205-A334-B844 (English) or A24205-A334-A844 (German).

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Siemens Unité de contrôle

Siemens

Siemens SIMATIC NET CP 1628 Manuel utilisateur

Siemens

Siemens SIMATIC ET 200SP Document technique

Siemens

Siemens SIMATIC ET 200SP CM 1xDALI Manuel du propriétaire

Siemens

Siemens SIRIUS 3RU Series Manuel utilisateur

Siemens

Siemens SIMOCODE pro C Guide de l'utilisateur

Siemens

Siemens MOBY I ASM 421 Manuel de la liste des pièces

Siemens

Siemens 2AI 2/4WIRE HF Manuel utilisateur

Siemens

Siemens RC-30U Manuel utilisateur

Siemens

Siemens SCALANCE W788C-2 Manuel utilisateur

Siemens

Siemens CB15 Manuel utilisateur

Siemens

Siemens PM-E F pm DC24V PROFIsafe Manuel utilisateur

Siemens

Siemens 3UF51 Manuel utilisateur

Siemens

Siemens SIRIUS 3RA2711 C Series Manuel utilisateur

Siemens

Siemens SINAMICS G120D Manuel utilisateur

Siemens

Siemens SIMOTION D4x5-2 Manuel utilisateur

Siemens

Siemens SIMATIC ET 200AL Manuel utilisateur

Siemens

Siemens Simatic S7-1500 Manuel utilisateur

Siemens

Siemens ZU-35 Manuel utilisateur

Siemens

Siemens EFB300 Manuel utilisateur

Siemens

Siemens Simatic S7-300 Manuel utilisateur

Siemens

Siemens SINUMERIK 802D Guide d'installation

Siemens

Siemens PS-35 Manuel utilisateur

Siemens

Siemens SICAM A8000 Series Manuel utilisateur

Siemens

Siemens RHFL Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur