Siemens XLD-1 Manuel utilisateur

P/N 315-093385-8

Installation Instructions

Model XLD-1

Analog Loop Driver

OPERATION

The Model XLD-1 from Siemens Building Technolo-

gies, Inc. is an optional MXL network module that

connects XL3 analog addressable devices to the

MXL System. The module uses four consecutive

network addresses on the System. Devices

connected to the XLD-1 circuits are supervised by

the MXL Control Panel.

Each of the XLD-1 circuits supports up to 30

alarm causing, trouble causing, and supervisory

type devices, as well as intelligent output de-

vices. Each device has its own address. The

sensitivity of any analog smoke detector is

checked and adjusted from the Control Panel.

Sensitivity, as well as other device information, is

displayed at the Control Panel. The XLD-1 also

supports the use of relay bases.

Each XLD-1 circuit can be wired in either a Class B

or Class A configuration. When using Class B, T-

tapping is permitted with no loss of supervision.

The XLD-1 module has an on-board micro-

processor which provides it with the ability to

function and to initiate alarm conditions even if the

MXL main processor fails. The module also has

four LEDS, which can indicate alarm, trouble,

transmit, or ground fault. (Refer to Figure 1.)

For additional information on the MXL/MXLV

System, refer to the MXL/MXLV Manual, P/N

315-092036.

INSTALLATION

Remove all system power before installa-

tion, first battery and then AC. (To power up,

connect the AC first and then the battery.)

The XLD-1 installs into the MXL optional MOM-4

card cage where it plugs into one full width slot.

The XLD-1 can be installed in either of the full

width slots of the MOM-4 (See Figure 2). The slot

determines whether the device loops are avail-

able on TB1 or TB2 of the MOM-4.

Before installing the XLD-1 in the MOM-4, set the

network address using switch S1 (Refer to Figure

1 for the location of S1). Set it to the lowest of the

four corresponding addresses selected for it in the

CSG-M. (The lowest address may be odd or

Figure 1

XLD-1 Board

Fire Safety

Siemens Building Technologies, Inc.

8 Fernwood Road

Florham Park, New Jersey 07932

Siemens Building Technologies, Ltd.

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 Canada

even.) Follow the appropriate switch positions in

Table 1 on the back page to set the address (See

NOTE below).

The table below illustrates sample XLD-1 module

addresses:

XLD-1 at Module

Addresses 3, 4, 5, and 6 Devices

Loop 1

Loop 4

003-01 to 003-30

006-01 to 006-30

XLD-1 at Module

Addresses 15, 16, 17, and 18 Devices

Loop 1

Loop 4

015-01 to 015-30

018-01 to 018-30

NOTE: To open a dipswitch, press down on the side

of the dipswitch marked OPEN. To close a dipswitch,

press down on the side of the dipswitch opposite the

side marked OPEN.

To open a slide switch, push the slide to the

side opposite the side marked ON. To close a slide

switch, push the slide to the side marked ON.

After the address is set, install the XLD-1 in the

MOM-4, being sure that the module is riding in

the card guides and is firmly seated in the card

edge connector. Eliminate all troubles from each

XLD-1 before installing the next one.

Electrical connections for the four addressable

initiating zones are shown in Figure 3.

Electrical Ratings

(Refer to Figure 3)

Figure 2

Slots for the XLD-1

FULL

WIDTH

SLOT

FULL

WIDTH

SLOT

Compatible Devices

1. All circuits are power limited to NFPA 70 per

Article 760. Each detector or group of

detectors must use a 2-wire circuit of at least

18 AWG thermoplastic fixture wire enclosed

in conduit, or 18 AWG limited energy shielded

cable without conduit, if permitted by local

building codes.

2. No end of line device is required for these

initiating loops.

3. Up to 30 devices can be used per loop. See

the Compatibility Table for the XLD-1 for a

list of compatible devices. Use any combi-

nation of those listed.

The compatibility identifiers for the compatible

devices are the model numbers listed in the

Compatibility Table

5. Total circuit resistance must not exceed 100

ohms.

Maximum capacitance:

0.4uF, between loop+ and loop–

0.8uF, between loop+ and chassis

0.8uF, between loop– and chassis

6. T-tapping is not allowed on Class A loops.

Initiating circuits

28 V unfiltered full wave rectified peak (Alarm and Supervisory)

40mA max per circuit (0-30 devices in alarm)

Battery Calculations

XLD-1 Module Current: 215mA

Device Current: 1.1mA per device

tnerruCeludoMCDV5evitcAAm0

tnerruCeludoMCDV42evitcA +Am022

ecivedrepAm1.1

tnerruCeludoMCDV42ybdnatS +Am022

civedrepAm1.1

Figure 3

XLD-1 Wiring Diagram

POSITIVE AND NEGATIVE GROUND FAULT DETECTED AT <40K OHMS FOR TERMINALS 1-16.

1-DLXROFELBATYTILIBITAPMOC

elbitapmoC

seciveD

noitallatsnI

snoitcurtsnI

elbitapmoC

seciveD

noitallatsnI

snoitcurtsnI

3XA-ID

H3XA-ID

3XB-ID

H3XB-ID

3X-ID

H3X-ID

3X-PD

531-3X-TD

HI06/I06-DI

HAI06/AI06-DI

HBI06/BI06-DI

TP06/P06-DI

531-T06-DI

HA1/A1/H1/1

-ILI

HB1/B1-ILI

F883580-513N/P

B885680-513N/P

8-095680-513N/P

6-295680-513N/P

8-095680-513N/P

6-295680-513N/

D435380-513N/P

B785680-513N/P

A604380-513N/P

C521480-513N/P

2-782090-513N/P

8-095680-513N/

6-295680-513N/P

3-982090-513N/P

2-882090-513N/P

4-783590-513N/P

6-432390-513N/P

5-532390-513N/P

1-PLI

1-TPL

1-TLI

02/01-ISM

B02/B01-ISM

1-XSM

2-XSM

1-XAP

3-XAP

0003-XEP

T0003-XEP

1-XAS

3-XAS

D2/R2/2-IRT

D06/R06/06-IRT

D6B/R6B/6B-IRT

1-XRT

R2/D2/2-XRT

3-XRT

8-495290-513N/P

1-633390-513N/P

3-309090-513N/P

7-923390-513N/P

C340381-513N/P

B825880-513N

C516480-513N/P

3-855780-513N/P

C255680-513N/P

C416480-513N/P

A197780-513N/P

5-655090-513N/

3-923290-513N/P

3-513390-513N/P

E264381-513N/P

4-876680-513N/P

A882680-513N/P

noitidEht8468LUrepdetsiL§

P/N 315-093385-8

1ELBAT

GNIMMARGORPSSERDDAKROWTEN

RDDA12345678RDDA12345678RDDA12345678RDDA12345678

000

100

200

300

400

500

600

700

800

900

010

110

210

310

410

510

610

710

810

910

020

120

220

320

420

520

620

720

820

920

030

130

230

330

430

530

630

730

830

930

040

140

240

340

440

540

640

740

840

940

050

150

250

450

550

650

750

850

950

060

160

260

360

LAGELLI

XXOOOOOO

OOXOOOOO

XOXOOOOO

OXXOOOOO

XXXOOOOO

OOOXOOOO

OOXOOOO

OXOXOOOO

XXOXOOOO

OOXXOOOO

XOXXOOOO

OXXXOOOO

XXXXOOOO

OOOOXOOO

XOOOXOOO

OXOOXOOO

XXOOXOOO

OOXOXOOO

XOXOXO

OXXOXOOO

XXXOXOOO

OOOXXOOO

XOOXXOOO

OXOXXOOO

XXOXXOOO

OOXXXOOO

XOXXXOOO

OXXXXOOO

XXXXXOOO

OOOOOXOO

XOOOOXOO

OXO

OOXOO

XXOOOXOO

OOXOOXOO

XOXOOXOO

OXXOOXOO

XXXOOXOO

OOOXOXOO

XOOXOXOO

OXOXOXOO

XXOXOXOO

OOXXOXOO

XOXXOXOO

OXXXOXOO

XXXXOXOO

OOOOXXOO

XOOOXXOO

OXOOXXOO

XXOOXXOO

OOXOXXOO

XOXOXXOO

OXXOXXOO

XXXOXXOO

OOOXXXOO

XOOXXXOO

OXOXXXOO

XXOXX

XOO

OOXXXXOO

XOXXXXOO

OXXXXXOO

XXXXXXOO

460

560

660

760

860

960

070

170

270

370

470

570

670

770

870

970

080

180

280

380

480

580

680

780

880

980

090

190

290

390

490

590

690

790

890

990

001

101

201

301

401

501

601

701

801

901

011

111

211

311

411

511

611

711

811

021

121

221

321

421

521

621

721

OOOOOOXO

XOOOOOXO

OXOOOOXO

XXOOOOXO

OOXOOOXO

XOXOOOXO

OXXOOOXO

XXXOOOXO

OOOXOOXO

XOOX

OOXO

OXOXOOXO

XXOXOOXO

OOXXOOXO

XOXXOOXO

OXXXOOXO

XXXXOOXO

OOOOXOXO

XOOOXOXO

OXOOXOXO

XXOOXOXO

OOXOXOXO

XOXOXOXO

XXOXOXO

XXXOXOXO

OOOXXOXO

XOOXXOXO

OXOXXOXO

XXOXXOXO

OOXXXOXO

XOXXXOXO

OXXXXOXO

XXXXXOXO

OOOOOXXO

XOOOOXXO

OXOOOX

XXOOOXXO

OOXOOXXO

XOXOOXXO

OXXOOXXO

XXXOOXXO

OOOXOXXO

XOOXOXXO

OXOXOXXO

XXOXOXXO

OOXXOXXO

XOXXOXXO

OXXXOXXO

XXX

XOXXO

OOOOXXXO

XOOOXXXO

OXOOXXXO

XXOOXXXO

OOXOXXXO

XOXOXXXO

OXXOXXXO

XXXOXXXO

OOOXXXXO

XOOXXXXO

OXOXXXXO

XXOXXXXO

OOXXXXXO

XOXXXXXO

OXXXXXXO

XXXXXXXO

821

921

031

131

231

331

431

531

631

731

831

931

041

141

241

341

441

541

641

741

841

941

051

151

251

351

451

551

651

751

851

951

061

161

261

361

461

561

661

761

861

961

071

171

271

371

471

571

671

771

871

971

081

181

281

381

581

681

781

881

981

091

191

OOOOOOOX

XOOOOOOX

OXOOOOOX

XXOOOOOX

OOXOOOOX

XOXOOOOX

OXXOOOOX

XXXOOOOX

OOOXOOOX

XOOXOOO

OXOXOOOX

XXOXOOOX

OOXXOOOX

XOXXOOOX

OXXXOOOX

XXXXOOOX

OOOOXOOX

XOOOXOOX

OXOOXOOX

XXOOXOOX

OOXOXOOX

XOXOXOOX

OXXO

XOOX

XXXOXOOX

OOOXXOOX

XOOXXOOX

OXOXXOOX

XXOXXOOX

OOXXXOOX

XOXXXOOX

OXXXXOOX

XXXXXOOX

OOOOOXOX

XOOOOXOX

OXOOOXOX

XOOOXOX

OOXOOXOX

XOXOOXOX

OXXOOXOX

XXXOOXOX

OOOXOXOX

XOOXOXOX

OXOXOXOX

XXOXOXOX

OOXXOXOX

XOXXOXOX

OXXXOXOX

XXXXOX

OOOOXXOX

XOOOXXOX

OXOOXXOX

XXOOXXOX

OOXOXXOX

XOXOXXOX

OXXOXXOX

XXXOXXOX

OOOXXXOX

XOOXXXOX

OXOXXXOX

XXOXXXOX

OOX

XXXOX

XOXXXXOX

OXXXXXOX

XXXXXXOX

291

391

491

591

691

791

891

991

002

102

202

302

402

502

602

702

802

902

012

112

212

312

412

512

612

712

812

912

022

122

222

322

422

522

622

722

822

922

032

132

232

332

432

532

632

732

832

932

042

142

242

342

442

542

642

742

842

052

152

252

352

452

552

OOOOOOXX

XOOOOOXX

OXOOOOXX

XXOOOOXX

OOXOOOXX

XOXOOOXX

OXXOOOXX

XXXOOOXX

OOOXOOXX

XOOXOOXX

OXOOXX

XXOXOOXX

OOXXOOXX

XOXXOOXX

OXXXOOXX

XXXXOOXX

OOOOXOXX

XOOOXOXX

OXOOXOXX

XXOOXOXX

OOXOXOXX

XOXOXOXX

OXXOXOX

XXXOXOXX

OOOXXOXX

XOOXXOXX

OXOXXOXX

XXOXXOXX

OOXXXOXX

XOXXXOXX

OXXXXOXX

XXXXXOXX

OOOOOXXX

XOOOOXXX

OXOOOXXX

XXOO

OXXX

OOXOOXXX

XOXOOXXX

OXXOOXXX

XXXOOXXX

OOOXOXXX

XOOXOXXX

OXOXOXXX

XXOXOXXX

OOXXOXXX

XOXXOXXX

OXXXOXXX

XXXXOXXX

OOOXXXX

XOOOXXXX

OXOOXXXX

XXOOXXXX

OOXOXXXX

XOXOXXXX

OXXOXXXX

XXXOXXXX

LAGELLI

LAG

ELLI

LAGELLI

)NOro(DESOLC=X)FFOro(NEPO=O

Autres manuels Siemens Unité de contrôle

Siemens

Siemens SINUMERIK 840C Guide de configuration

Siemens

Siemens AP 641 Manuel de service

Siemens

Siemens SITRANS AW 7MP3112 Series Manuel utilisateur

Siemens

Siemens SINAMICS G120P Instructions de montage

Siemens

Siemens SINUMERIK 840C Manuel utilisateur

Siemens

Siemens SIMOCODE pro 3UF7400-1AA00-0 Manuel utilisateur

Siemens

Siemens MJ-4 Series Manuel utilisateur

Siemens

Siemens SIRIUS 3RK3 Manuel utilisateur

Siemens

Siemens SINAMICS S120 Document technique

Siemens

Siemens SIMATIC 500 Series Manuel

Siemens

Siemens A80407-01 Manuel utilisateur

Siemens

Siemens SIMOTION D425 Manuel utilisateur

Siemens

Siemens SENTRON 7KM PAC 4DI/2DO Manuel utilisateur

Siemens

Siemens CU230P-2 HVAC Manuel utilisateur

Siemens

Siemens 7KM4211-1BA00-3AA0 Manuel utilisateur

Siemens

Siemens SIRIUS ACT 3SU1400-2EM10-6AA0 Manuel utilisateur

Siemens

Siemens SIMATIC ET 200SP IM 155-6 PN/2 HF Manuel utilisateur

Siemens

Siemens SIMATIC Panel PC 677 Manuel utilisateur

Siemens

Siemens SIPLUS CMS4000 IFN VIB-A Manuel utilisateur

Siemens

Siemens SINUMERIK 808D Guide d'installation

Siemens

Siemens Simatic S7-1500 Manuel utilisateur

Siemens

Siemens SIMATIC IM 151/CPU Manuel utilisateur

Siemens

Siemens SINAMICS G120P Manuel utilisateur

Siemens

Siemens SENTRON PROFINET Proxy SPP2000 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur