Siemens SIMATIC S7-1500R/H Manuel utilisateur

___________________

SIMATIC

S7-1500

S7-1500R/H redundant system

Getting Started

10/2018

A5E44910930

-AA

Introduction to the example

Configuration

Programming

Commissioning

Additional information

Siemens AG

Division Digital Factory

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E44910930-AA

Ⓟ

09/2018 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

S7-1500R/H redundant system

Getting Started, 10/2018, A5E44910930-AA 3

Table of contents

1 Introduction to the example ..................................................................................................................... 4

1.1 Security information ..................................................................................................................5

1.2 Structure and task of the example ............................................................................................6

1.3 Procedure ...............................................................................................................................11

1.4 Requirements..........................................................................................................................12

1.5 Wiring diagram for a tunnel section ........................................................................................13

2 Configuration ........................................................................................................................................ 19

2.1 Configuring the assembly .......................................................................................................19

2.2 Configuring H CPUs................................................................................................................22

2.3 Configuring ET 200SP ............................................................................................................25

2.4 Configuring HMI devices.........................................................................................................30

3 Programming ........................................................................................................................................ 34

4 Commissioning ..................................................................................................................................... 48

5 Additional information............................................................................................................................ 51

S7-1500R/H redundant system

4Getting Started, 10/2018, A5E44910930-AA

Introduction to the example

Redundant automation systems are used in practice to achieve greater availability. In

redundantly operated systems, failure or malfunction of individual automation components

must not impede the operation of the plant.

S7-1500R/H redundant system

For the S7-1500R/H redundant system, the CPUs are duplicated, in other words redundant.

The two CPUs process the same project data and the same user program in parallel. The

two CPUs are synchronized over redundancy connections. If one CPU fails, the other CPU

maintains control of the process.

Basic knowledge required

The Getting Started guides you through the configuration and programming of an S7-1500H

redundant system using a concrete example. The following knowledge is required in order to

understand the Getting Started:

●General knowledge of automation technology

●Knowledge of requirements for high availability of automation systems

●Knowledge of the engineering system STEP 7 V15.1

WARNING

Personal injury and damage to property may occur.

The S7-1500 as a component of plants or systems is governed by specific standards and

regulations, based on the relevant field of application. Please observe the applicable safety

and accident prevention regulations such as IEC 60204-1 (general machine safety

requirements).

The example in this Getting Started serves as an introduction to the configuration and

programming of an S7-1500H redundant system. It cannot always and in every case be

transferred to effective live operations. Before you do this, you are urgently advised to

consult the current version of the system manual "SIMATIC S7-1500R/H redundant

system" and the device manuals of the modules used. The warnings and other information

there must be observed, even if they are not repeated in this Getting Started.

Failure to observe these regulations can result in serious injuries and damages to

machinery and facilities.

Introduction to the example

1.1 Security information

S7-1500R/H redundant system

Getting Started, 10/2018, A5E44910930-AA 5

1.1

Security information

Siemens provides products and solutions with industrial security functions that support the

secure operation of plants, systems, machines and networks.

In order to protect plants, systems, machines and networks against cyber threats, it is

necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial

security concept. Siemens' products and solutions constitute one element of such a concept.

Customers are responsible for preventing unauthorized access to their plants, systems,

machines and networks. Such systems, machines and components should only be

connected to an enterprise network or the internet if and to the extent such a connection is

necessary and only when appropriate security measures (e.g. firewalls and/or network

segmentation) are in place.

For additional information on industrial security measures that may be implemented, please

visit (https://www.siemens.com/industrialsecurity).

Siemens' products and solutions undergo continuous development to make them more

secure. Siemens strongly recommends that product updates are applied as soon as they are

available and that the latest product versions are used. Use of product versions that are no

longer supported, and failure to apply the latest updates may increase customers' exposure

to cyber threats.

To stay informed about product updates, subscribe to the Siemens Industrial Security RSS

Feed under (https://www.siemens.com/industrialsecurity).

Introduction to the example

1.2 Structure and task of the example

S7-1500R/H redundant system

6Getting Started, 10/2018, A5E44910930-AA

1.2

Structure and task of the example

Automation task light and fan control in a tunnel

The continuing increase in traffic volumes coupled with growing safety requirements demand

state-of-the-art tunnel systems. At the same time, equipment requirements for these

constructions are rising, especially when it comes to maximum safety and availability.

The example below comprises three subtasks:

●Control of the safety ventilation as a function of the air pollution level in the tunnel

●Control of the traffic lights and the barriers as a function of the air pollution level in the

tunnel

●Control of the lighting in the tunnel as a function of the illuminance of the outdoor light

Figure 1-1 Example Light and fan control tunnel

Control of the safety ventilation as a function of the air pollution level in the tunnel

Fans are used in the tunnel to extract harmful exhaust gases and supply fresh air.

Uninterrupted operation of the ventilation system is required to keep the concentration of

pollutants below a set level. Constant availability must be ensured for the event that

individual automation components fail, for example because of a fire in the tunnel. The S7-

1500H redundant system with two redundant H-CPUs is used to ensure fan availability.

Three fans ventilate the tunnel.

Control of the traffic lights and the barriers as a function of the air pollution level in the tunnel

The tunnel entries are controlled via two traffic lights. The traffic light control also requires

higher availability for safety reasons.

If the pollutant concentration exceeds a maximum limit for more than 2 minutes in a tunnel

section, then the tunnel is blocked.

Control of the lighting in the tunnel as a function of the illuminance of the outdoor light

The abrupt transition between light and dark at the entry to the tunnel is compensated for by

tunnel lighting in the various tunnel sections. Two light sensors measure the light intensity

outside the tunnel. The light intensity of the entry lights in the tunnel is controlled accordingly.

The interior lights in the tunnel are controlled by the prevailing daytime / nighttime.

Introduction to the example

1.2 Structure and task of the example

S7-1500R/H redundant system

Getting Started, 10/2018, A5E44910930-AA 7

Technology diagram

The technology diagram below shows the structure of the automation solution.

①

Tunnel lighting

②

Fan

③

Traffic lights

④

Barriers

⑤

Outdoor light sensors

⑥

Turbidity sensors

⑦

Air-quality sensors

⑧

HMI devices

⑨

H-CPUs

⑩

IO devices for tunnel sections 1 to 3

Figure 1-2 Technology diagram

Introduction to the example

1.2 Structure and task of the example

S7-1500R/H redundant system

8Getting Started, 10/2018, A5E44910930-AA

Automation components of the example

The configuration consists of:

2 S7-1500 H-CPUs

●When a CPU fails in redundant operation, the other CPU maintains control over the

tunnel operation.

3 ET 200SP as IO devices in the PROFINET ring

An ET 200SP (IO device) distributed I/O system is found in every tunnel section (1 to 3).

Sensors and actuators are connected to each IO device for the following tasks:

●Measurement of the pollutant concentration and as a function thereof:

–Control of the fan speed and air flow

–Control of the traffic lights and barriers

●Measurement of the light outside the tunnel:

–Control of the entry lights

●Control of the interior lights in the tunnel, depending on the day / night time.

2 Comfort Panels

The Comfort Panels are used by operators as a control center for monitoring tunnel

operation.

Introduction to the example

1.2 Structure and task of the example

S7-1500R/H redundant system

Getting Started, 10/2018, A5E44910930-AA 9

Principle of operation

Controlling the speed of the fans and controlling the traffic lights and barriers

Every fan:

●has two speeds (stages), which are switched on or off depending on the measured

pollutant concentration.

●has 2 directions of rotation. Depending on whether pollution is measured, the fan must

blow or suck.

The H-CPU measures the pollutant concentrations in the tunnel via analog input modules

and air-quality sensors.

If the pollutant concentration exceeds the maximum limit, the H-CPU responds in ET 200SP

via digital output modules as follows:

●It increases the speed of the fan motors

●It switches the traffic light system to red after two minutes

●It closes the barriers after two minutes

If the pollutant concentration falls below an average limit, the H-CPU responds in ET 200SP

via digital output modules as follows:

●It switches the ventilation motors to stop

●It switches the traffic lights to green

●It opens the barriers

Controlling the lighting in the tunnel

The H-CPU measures the light intensity outside and inside the tunnel using analog input

modules. Depending on the outdoor light, digital output modules adjust the brightness of the

entry lights in the tunnel to the optimum vision conditions. The digital output modules also

control the interior lights in the tunnel, depending on the day / night time.

The user program

in the CPU specifies limits and controls the input and output modules of

the ET 200SP.

The Comfort Panels

visualize the S7-1500H redundant system in an HMI screen. If required,

the operator can switch to manual operation via the HMI screen and change limit values.

Autres manuels pour SIMATIC S7-1500R/H

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Siemens Unité de contrôle

Siemens

Siemens SINAMICS DCM Manuel utilisateur

Siemens

Siemens SIMATIC NET 6GK1110-1AA00 Manuel utilisateur

Siemens

Siemens EN100 Manuel utilisateur

Siemens

Siemens V-2030 Manuel utilisateur

Siemens

Siemens ECOFAST 3RK1911-4AB Series Manuel utilisateur

Siemens

Siemens SINAMICS CONNECT 500 Manuel utilisateur

Siemens

Siemens SIMATIC NET Manuel utilisateur

Siemens

Siemens SINUMERIK Series Manuel de la liste des pièces

Siemens

Siemens SIMOTION D425-2 Manuel utilisateur

Siemens

Siemens SIRIUS 3RT1.5 Manuel utilisateur

Siemens

Siemens 3AK Manuel utilisateur

Siemens

Siemens SINAMICS G120P CU230P-2 Guide de l'administrateur

Siemens

Siemens 3VM9.88-0LB10 Manuel utilisateur

Siemens

Siemens SCALANCE S615 Manuel utilisateur

Siemens

Siemens SIMATIC 6ES7135-4MB02-0AB0 Manuel utilisateur

Siemens

Siemens SIMOCODE pro Manuel utilisateur

Siemens

Siemens 7KM9300-0AE01-0AA0 Manuel utilisateur

Siemens

Siemens Simatic RTU3030C Manuel utilisateur

Siemens

Siemens SIRIUS 3RK3 Manuel utilisateur

Siemens

Siemens SIMATIC S7 3964 Manuel d'instructions

Siemens

Siemens Cm-lon 6BK1700-0BA10-0AA00 Manuel utilisateur

Siemens

Siemens SIMADYN D SS52 Manuel utilisateur

Siemens

Siemens SIDOOR AT40 Guide de l'utilisateur

Siemens

Siemens SIMOTION D410 PN Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur