Siemens HLIM Manuel utilisateur

Siemens Building Technologies

Fire Safety

P/N 315-033170-2

OPERATION The SIEMENS Model HLIM Loop Isolator Module solates short c rcu ts on F reF nder-

XLS analog loops. By plac ng dev ces between HLIMs dur ng nstallat on, a short n

the w r ng w th n that group s d sconnected from the rest of the loop. The rema nder

Figure 1

The HLIM-1 Loop Isolator Module

does not have a loop address and therefore does not requ re address programm ng

nor does t reduce the loop capac ty below 252 dev ces.

Remove all system power before installation, first the battery and then the AC.

INSTALLATION The HLIM s a polar ty nsens t ve module. Refer to F gure 1 for the locat on of the

two nput term nals and two output term nals. L ne 1 and L ne 2 can be e ther l ne of

the loop.

The HLIM may be used n two c rcu t conf gurat ons as follows:

Class B (See F gure 2) In Class B w r ng each HLIM solates a branch on the c rcu t. Note that

a short on the ma n branch causes the ent re loop to fa l. To prevent th s, mount the

HLIMs at the F reF nder-XLS enclosure and run each branch ndependently.

of the dev ces cont nue

to operate. The HLIM

operates n both Class A

and Class B c rcu ts.

A yellow LED flashes

when a dev ce detects a

short c rcu t. The HLIM

then solates that part of

the loop. When the short

s removed, the HLIM

automat cally restores

the loop to normal

operat on. The HLIM

FRONT BACK

FAULT

IN - LINE 1

IN - LINE 2

OUT - LINE 1

OUT - LINE 2

Loop Isolator Module

Installation Instructions

Model HLIM

Siemens Building Technologies

Fire Safety

P/N 315-033170-

Figure 2

HLIM Wiring Diagram - Class B Installation

Class A S ngle Loop (See F gure 3) In Class A w r ng the HLIMs are w red n ser es w th the loop w r ng.

Th s results n a s ngle cont nuous loop. If any group n the loop has a short, that

group s lost and a Class A c rcu t fa lure results. The F reF nder-XLS d splays commu-

n cat on errors for the dev ces and a Class A fa lure for the loop tself.

Figure 3

HLIM Wiring Diagram - Class A Installation Single Loop)

1. All wiring must comply with

national and local codes.

. In order to provide adequate

protection, it is recom-

mended that you do not

install more than 0 devices

on a single HLIM.

3. Minimum wire gauge is

18 AWG.

4. The total wire resistance

(both wires) between HLIMs

cannot exceed 0 ohms.

5. Do not install more than 15

HLIMs per DLC loop.

6. All circuits are supervised.

7. Refer to DLC Installation

Instructions, P/N 315-033090

for the list of compatible

devices.

8. All terminals are power

limited.

1. All wiring must comply with

national and local codes.

. In order to provide adequate

protection, it is recom-

mended that you do not

install more than 0 devices

on a single HLIM.

3. Minimum wire gauge is

18 AWG.

4. The total wire resistance

(both wires) between HLIMs

cannot exceed 0 ohms.

5. Do not install more than 15

HLIMs per DLC loop.

6. All circuits are supervised.

7. Refer to DLC Installation

Instructions, P/N 315-033090

for the list of compatible

devices.

8. All terminals are power

limited.

ANALOG LOOP

LINE 1

LINE 2

IN IN OUT OUTIN IN OUT OUTIN IN OUT OUT

TO ANALOG

LOOP RETURN

INSIDE ENCLOSURE

TO ANALOG

LOOP FEED

LINE 1

LINE 2

LINE 1

IN IN OUT OUT

IN IN OUT OUT IN IN OUT OUT

ININ

OUTOUT

ININ

OUTOUT

ININ

OUTOUT

Siemens Building Technologies

Fire Safety

P/N 315-033170-3

Figure 4

Mounting

Mechan cal Installat on (See F gure 4)

 Use a standard 3 1/2- nch deep, double gang electr cal sw tchbox or a 4- nch

square electr cal box that s 2 1/8 nches deep.

 Connect the f eld w r ng. Press the HLIM nto the box and fasten the

module plate to the box.

 Cover the module front plate w th the plate suppl ed and fasten w th screws

suppl ed.

ELECTRICAL RATINGS Input power: 24 VDC, 1mA max

SWITCHPLATE

4-INCHES SQUARE

(SUPPLIED)

SWITCHPLATE

(SUPPLIED)

4-INCHES SQUARE

4-INCH SQUARE BOX

2 1/8-INCHES DEEP

DOUBLE GANG BOX

3 1/2-INCHES DEEP

Siemens Building Technologies, Inc.

8 Fernwood Road

Florham Park, New Jersey 0793

Siemens Building Technologies, Ltd.

Kenview Boulevard

Brampton, Ontario L6T 5E4 P/N 315-033170-

Table des matières

Autres manuels Siemens Unité de contrôle

Siemens

Siemens P Series Manuel utilisateur

Siemens

Siemens SINUMERIK 840D Manuel utilisateur

Siemens

Siemens SINUMERIK 840D sl Manuel du propriétaire

Siemens

Siemens SINUMERIK 880 Mode d'emploi

Siemens

Siemens SIRIUS 3SB3 Manuel utilisateur

Siemens

Siemens SIMATIC IM 153-2 Manuel utilisateur

Siemens

Siemens CZM-4 Manuel utilisateur

Siemens

Siemens 3VT9300-4WA30 Manuel utilisateur

Siemens

Siemens QAA73.210 Manuel utilisateur

Siemens

Siemens SIMATIC S7-1200 Manuel de la liste des pièces

Siemens

Siemens REMBOX2-MP Manuel utilisateur

Siemens

Siemens RHFL Manuel utilisateur

Siemens

Siemens RM-30U Manuel utilisateur

Siemens

Siemens 3UF51 Manuel utilisateur

Siemens

Siemens SINAMICS S120 Document technique

Siemens

Siemens 7SC80 Manuel utilisateur

Siemens

Siemens Synco RMZ792 Manuel de l'opérateur

Siemens

Siemens SINUMERIK 828D Turning Manuel utilisateur

Siemens

Siemens SIMOVERT Masterdrives SSB Manuel utilisateur

Siemens

Siemens SINUMERIK 840D sl Manuel utilisateur

Siemens

Siemens SIRIUS 3RT1916-4KA Manuel utilisateur

Siemens

Siemens WATCHDOG-Modul ET 200iSP Manuel utilisateur

Siemens

Siemens SIMADYN D T400 Manuel de la liste des pièces

Siemens

Siemens SIMATIC ET 200SP Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur