Siemens 8DO Manuel utilisateur
Installation Instructions
Document No. 129-565
April 28, 2015
EcoView™ 8 DO Module Installation and Commissioning
Item Number 129-565, Rev. CA Page 1 of 5
This document covers the installation and
commissioning of the EcoView™ 8 DO Module.
See the following documents for installation of other
EcoView system components:
EcoView Touchscreen Installation and System
Start-up
(129-562)
EcoView Thermostat Installation Instructions
(129-564 or 129-566)
EcoView Multi-phase Meter Installation
Instructions
(129-563)
Product Description
The EcoView 8 DO Module is an eight-channel, pilot-
duty controller module that is used to manage lighting
or other energy-consuming electrical loads that would
benefit from scheduling. Relay channels may be
accessed through the EcoView Touchscreen or
remotely through the EcoView Web application.
Product Number
57-002
EcoView I/O Module, 8 DO, with Zigbee,
includes power supply
Caution Notations
CAUTION:
Equipment damage or loss of
data may occur if you do not
follow the procedures as
specified.
Required Tools and Materials
Flat-blade screwdriver (1/8-inch blade width)
Wire strippers
Expected Installation Time
15 minutes for installing the EcoView 8 DO Module
30 minutes for wiring each DO
Prerequisites
NOTE: If the EcoView 8 DO Module will be directly
controlling line voltage, it must be mounted in
an appropriate plastic NEMA enclosure.
The EcoView Touchscreen is installed and started up
according to the
Installation Instructions
(129-562).
A 120 Vac outlet is available for the EcoView 8
DO Module power supply.
Depending on the type of installation, other
prerequisites may have to be completed.
Installation
CAUTION:
Always wear an electro-static discharge
(ESD) wrist strap and discharge
accumulated static before touching field
panel components.
Install the EcoView 8 DO Module near the loads
to be controlled.
1. If the EcoView 8 DO Module will be directly
controlling line voltage, mount the plastic NEMA
enclosure in the desired location.
2. If necessary, install a standard 120 Vac outlet in
the enclosure where the EcoView 8 DO Module
power supply will be attached.
3. Using the provided screws, mount the EcoView 8
DO Module assembly in the enclosure.
4. Attach the EcoView 8 DO Module 24 Vac power
supply to the standard 120 Vac outlet and secure
with the provided plate screw.
5. Wire the individual circuits to be controlled to the
2-pin connectors for Relay 1 – Relay 8.
NOTE: The relays are capable of controlling loads up
to 240 Vac at 3A. Anything outside of this
range should be controlled by contactors.
Document No. 129-565
Installation Instructions
April 28, 2015
Page 2 of 5 Siemens Industry, Inc.
Figure 1: EcoView™ 8 DO Module Reset Button Location.
Commissioning the 8 DO Module
In order to commission the EcoView 8 DO Module to
the ZigBee network, the DO module needs to be reset.
1. Press the recessed Reset button four times in
rapid succession (see Figure 1).
The NET light stops flashing.
The NET light starts flashing again once it has
joined the ZigBee network.
2. Press the Reset button once to send the Node ID
information to the EcoView Touchscreen.
Assigning the 8 DO Module to the
Touchscreen
1. Press the EcoView Touchscreen CONFIG button
for one second and then release it to display the
Configuration screen (see Figure 6).
2. Press the DEVICE SETTINGS icon.
3. Press the Configure tab.
The EcoView 8 DO Module’s MAC address displays
in the Unassigned Nodes list. (See Figure 6.)
Assigned and unassigned EcoView 8 DO
Modules, EcoView Multi-phase Meters, and
EcoView Thermostats display in the
Configured Device list.
NOTE: Join devices one-at-a-time. This minimizes any
confusion caused by having several MAC
addresses displayed on the screen at one time.
4. Select a device from the Unassigned Nodes list
to start the Device Configuration Wizard.
Figure 2: Device Settings/Configure Tab.
5. Select the Resource Controller device driver
from the list, and then press the Next button.
Figure 3: Device Wizard Driver Selection.
6. If needed, select the Relay Delay parameter to
edit the value, and then press the Next button.
Figure 4: Device Wizard Parameters.
Siemens Industry, Inc.
Page 3 of 5
7. Select the appropriate Zigbee MAC Address for
the 8 DO Module from the list, and then press the
Finish button.
Figure 5: Device Wizard Zigbee MAC Selection.
8. Press the Accept button.
⇨The EcoView 8 DO Module is assigned to the
EcoView Touchscreen and locked into the
wireless network.
9. In the upper-left corner of the screen, press the
Home button to return to the main screen.
10. Press the Exit button to save the configuration.
The installation and commissioning are now complete.
Figure 6: Advanced Device Configuration Screen.
Troubleshooting
➤If the EcoView 8 DO Module’s MAC address is
not displayed on the Device Network screen,
repeat the steps in the
Commissioning the 8 DO
Module
section.
Removing Device(s) Installed to an EcoView
Touchscreen in Error (Only for Sites with
Multiple Touchscreens)
Use this procedure if the EcoView 8 DO Module has
joined the wrong EcoView Touchscreen network.
1. Remove the front bezel of the EcoView Touchscreen
that the 8 DO Mdoule has joined in error.
2. Press and hold the EcoView Touchscreen
CONFIG button for one second to display the
Configuration screen.
3. Press the DEVICE SETTINGS icon.
4. Press the Advanced tab.
5. On the right side of the screen, press the Open
button to toggle the network to closed.
The button text changes to Closed.
Document No. 129-565
Installation Instructions
April 28, 2015
Page 4 of 5 Siemens Industry, Inc.
6. Press the Configure tab and deselect Hide
Configured Devices.
7. In the list, select the EcoView 8 DO Module.
8. In the Device Configuration Wizard, press the
Decommission button.
9. Press the Accept button.
10. Return to the EcoView 8 DO Module and install it on
the correct EcoView Touchscreen network.
Resetting the EcoView 8 DO Module to
Manufacturer’s Defaults
Use this procedure to reset the EcoView 8 DO
Module to the manufacturer’s defaults.
➤Press and hold the recessed RESET button for
more than 10 seconds and then release it.
The LEDs on the EcoView 8 DO Module should
cycle off, then turn on again.
FCC and IC Interference
Requirements
“This device complies with Part 15 of the FCC Rules
and with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two
conditions (1) this device may not cause harmful
interference, and (2) this device must accept any
interference, including interference that may cause
undesired operation of the device.”
« Ce dispositif est conforme à la partie 15 des règles
de FCC et aux normes permis-exemptes du Canada
RSS d'industrie. L'opération est sujette aux deux
conditions suivantes (1) que ce dispositif peut ne pas
causer l'interférence nocive, et (2) ce dispositif doit
accepter n'importe quelle interférence, y compris
l'interférence qui peut causer le fonctionnement peu
désiré du dispositif. »
Per RSS-Gen Issue 3 (December 2010 Section 7.1.3)
FCC Note
This device complies with Part 15 of the FCC rules.
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC and IC Radiation Exposure
Statement for Mobile Devices
“This equipment complies with FCC and IC radiation
exposure limits set forth for an uncontrolled
environment. This equipment shall be installed and
operated with minimum distance 20cm between the
radiator and your body. This transmitter must not be
re-located or operating in conjunction with any other
antenna or transmitter.”
(For compliance with FCC Code of Federal
Regulations Title 47 Part 2.1093)
Document No. 129-565
Installation Instructions
April 28, 2015
Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and
models as design improvements are introduced. EcoView is a trademark of Siemens Industry, Inc. Other product or company names
mentioned herein may be the trademarks of their respective owners. © 2015 Siemens Industry, Inc.
Siemens Industry, Inc.
Building Technologies Division
Retail and Commercial Systems
1000 Deerfield Parkway
Buffalo Grove, IL 60089-4513
USA
+1 847-215-1000
For EcoView system support, please call
1 + 877-306-9400
Your feedback is important to us. If you have
comments about this document, please send
Document No. 129-565
Printed in the USA
Page 5 of 5
FCC Code of Federal
Regulations Title 47 Part
15.105
Information to the user:
This equipment has been tested and found to
comply with the limits for a Class B, digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turnings
the equipment off and on, the user is encouraged
to try to correct the interference by one or more of
the following measures:
Reorient or relocate receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV
technician for help.
For Industry Canada User
“This Class B digital apparatus complies with
Canadian ICES-003 Issue 4 (February 2004).”
« Cet appareillage numérique de la classe B est
conforme ICES-003 à l'issue canadienne 4 (le
février 2004). »
Antenna
“Under Industry Canada regulations, this radio
transmitter may only operate using an antenna of
a type and maximum (or lesser) gain approved for
the transmitter by Industry Canada. To reduce
potential radio interference to other users, the
antenna type and its gain should be so chosen
that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for
successful communication.”
« Aux termes des règlements du Canada
d'industrie, cet émetteur radioélectrique peut
seulement fonctionner utilisant une antenne d'un
type et (ou moins) d'un gain maximum approuvés
pour l'émetteur par Industry Canada. Pour
ramener des interférences radio potentielles à
d'autres utilisateurs, on devrait ainsi choisir le
type d'antenne et son gain que l'équivalent a
isotropically rayonné la puissance (e.i.r.p.) n'est
pas plus que celui nécessaire pour la
communication réussie. »
Table des matières
Autres manuels Siemens Unité de contrôle
Siemens
Siemens PSO+ Manuel utilisateur
Siemens
Siemens SIRIUS 3TK2834 Manuel utilisateur
Siemens
Siemens simovert masterdrives Manuel utilisateur
Siemens
Siemens SENTRON 7KM PAC 4DI/2DO Manuel utilisateur
Siemens
Siemens SIMATIC ET 200SP Manuel utilisateur
Siemens
Siemens SIMADYN D SS52 Manuel utilisateur
Siemens
Siemens 3RA2816-0EW20 Manuel utilisateur
Siemens
Siemens PS-35 Manuel utilisateur
Siemens
Siemens AP 641 Manuel de service
Siemens
Siemens SPCN110 Manuel utilisateur
Siemens
Siemens SINAMICS G120P Instructions de montage
Siemens
Siemens MJ-X Series Manuel utilisateur
Siemens
Siemens V P45 Series Manuel utilisateur
Siemens
Siemens SITOP PSE200U 3 A Manuel utilisateur
Siemens
Siemens WF 705 Instructions d'utilisation et d'installation
Siemens
Siemens HOTEL SOLUTION HTC3.1/A Manuel utilisateur
Siemens
Siemens SIMATIC ET 200SP CM 1xDALI Manuel utilisateur
Siemens
Siemens Simatic RTU3030C Manuel utilisateur
Siemens
Siemens SIMATIC ET 200SP Manuel utilisateur
Siemens
Siemens Simatic TI405 Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
