Siemens MICROMASTER 411 Manuel utilisateur
MICROMASTER 411 & COMBIMASTER 411
AS-i Module
Operating Instructions Issue 01/03
User Documentation
6SE6400-5AT00-0BP0
MICROMASTER 411 &
COMBIMASTER 411
AS-i Module
Operating Instructions
User Documentation
Valid for
Issue 01/03
MICROMASTER 411 &
COMBIMASTER 411
Issue 01/03
Description 1
Installing the AS-i
Module
2
Commissioning 3
Diagnostics and
Troubleshooting
4
Technical Data 5
MICROMASTER 411 & COMBIMASTER 411, AS-i Module Operating Instructions
46SE6400-5AT00-0BP0
Further information is available on the Internet under:
http://www.siemens.de/micromaster
Approved Siemens Quality for Software and Training
is to DIN ISO 14001, Reg. No. 2160-01
The reproduction, transmission or use of this document,
or its contents is not permitted unless authorized in
writing. Offenders will be liable for damages. All rights
including rights created by patent grant or registration of a
utility model or design are reserved.
© Siemens AG 2003. All Rights Reserved.
MICROMASTER® is a registered trademark of Siemens.
Other functions not described in this document may be
available. However, this fact shall not constitute an
obligation to supply such functions with a new control, or
when servicing.
We have checked that the contents of this document
correspond to the hardware and software described.
There may be discrepancies nevertheless, and no
guarantee can be given that they are completely identical.
The information contained in this document is reviewed
regularly and any necessary changes will be included in
the next edition. We welcome suggestions for
improvement.
Siemens handbooks are printed on chlorine-free paper
that has been produced from managed sustainable
forests. No solvents have been used in the printing or
binding process.
Document subject to change without prior notice.
Order Number. 6SE6400-5AT00-0BP0
Printed in the Federal of Germany
Siemens-Aktiengesellschaft.
Issue 01/03 Foreword
MICROMASTER 411 & COMBIMASTER 411, AS-i Module Operating Instructions
6SE6400-5AT00-0BP0 5
Foreword
User Documentation
WARNING
Before installing and commissioning the inverter, you must read all safety
instructions and warnings carefully including all the warning labels attached to the
equipment. Make sure that the warning labels are kept in a legible condition and
replace missing or damaged labels.
Information is also available from:
Technical Support Nuremberg
Tel: +49 (0) 180 5050 222
Fax: +49 (0) 180 5050 223
Email: techsupport@ad.siemens.de
Internet Home Address
Customers can access technical and general information at:
http://www.siemens.de/micromaster
Contact address
Should any questions or problems arise while reading this manual, please contact
the Siemens office concerned using the form provided at the back this manual.
Definitions and Warnings Issue 01/03
MICROMASTER 411 & COMBIMASTER 411, AS-i Module Operating Instructions
66SE6400-5AT00-0BP0
Definitions and Warnings
Safety guidelines
This manual contains notices intended to ensure your personal safety, as well as to
protect products and connected equipment against damage. Information relating to
your personal safety is highlighted by a warning triangle. Warnings about property
damage are displayed without a warning triangle. Depending on the degree of risk
involved, safety-related information is presented in the following categories:
DANGER
For the purpose of this documentation and the product warning labels, "Danger"
indicates that death, severe personal injury or substantial damage to property will
result if proper precautions are not taken.
WARNING
For the purpose of this documentation and the product warning labels, "Warning"
indicates that death, severe personal injury or substantial damage to property can
result if proper precautions are not taken.
CAUTION
With a warning triangle, "Caution" indicates that minor personal injury can result if
proper precautions are not taken.
CAUTION
Without a warning triangle, "Caution" indicates that material damage can result if
proper precautions are not taken.
ATTENTION
indicates that an undesirable effect or state can occur if attention is not paid to the
advice given.
NOTE
For the purpose of this documentation, "Note" indicates important information
relating to the product or highlights part of the documentation for special attention.
Qualified personnel
For the purpose of this Instruction Manual and product labels, a "Qualified person"
is someone who is familiar with the installation, mounting, start-up and operation of
the equipment and the hazards involved.
He or she must have the following qualifications:
1. Trained and authorized to energize, de-energize, clear, ground and tag circuits
and equipment in accordance with established safety procedures.
2. Trained in the proper care and use of protective equipment in accordance with
established safety procedures.
3. Trained in rendering first aid.
Issue 01/03 Definitions and Warnings
MICROMASTER 411 & COMBIMASTER 411, AS-i Module Operating Instructions
6SE6400-5AT00-0BP0 7
User Documentation
WARNING
Before installing and commissioning, please read these safety instructions and
warnings carefully and all the warning labels attached to the equipment. Make sure
that the warning labels are kept in a legible condition and replace missing or
damaged labels.
Proper use
Please note the following:
WARNING
This equipment contains dangerous voltages and controls potentially dangerous
rotating mechanical parts.
Non-compliance with Warnings or failure to follow the instructions contained in this
manual can result in loss of life, severe personal injury or serious damage to
property.
Only suitably qualified personnel should work on this equipment, and only after
becoming familiar with all safety notices and maintenance procedures contained in
this manual.
The successful and safe operation of this equipment is dependent upon its proper
handling, storage, installation, operation and maintenance.
National safety regulations are also applicable.
Use for intended purpose only
The equipment may be used only for the application stated in the manual and only
in conjunction with devices and components recommended and authorized by
Siemens.
Table of Contents Issue 01/03
MICROMASTER 411 & COMBIMASTER 411, AS-i Module Operating Instructions
86SE6400-5AT00-0BP0
Table of Contents
1 Description............................................................................................................... 9
2 Installing the AS-i Module .................................................................................... 11
2.1 Preparation of Inverter Terminal Housing ............................................................... 12
2.2 AS-i Module Installation .......................................................................................... 13
2.3 Addressing the AS-i Module.................................................................................... 15
3 Commissioning ..................................................................................................... 17
3.1 Parameter settings .................................................................................................. 17
3.2 AS-i Module Parameters ......................................................................................... 18
3.3 AS-i use data........................................................................................................... 19
4 Diagnostics and Troubleshooting ....................................................................... 21
5 Technical Data ....................................................................................................... 23
5.1 Technical Specifications.......................................................................................... 23
5.2 EMC Information ..................................................................................................... 23
Issue 01/03 Description
MICROMASTER 411 & COMBIMASTER 411, AS-i Module Operating Instructions
6SE6400-5AT00-0BP0 9
1 Description
The AS-i Module (Actuator sensor-Interface Communications Module) has been
designed to control the COMBIMASTER 411 and MICROMASTER 411 inverters
via:
ON/OFF commands
Fixed frequency selection
Reverse commands
Fault acknowledge commands
In the standard AS-i system up to 31 slaves can be connected, each slave having
up to 4 input and output bits.
Without the use of repeaters or extenders the maximum length of a cable segment
in the network is 100 meters (328 feet).
The AS-i Module is connected to the network via the FK cable adapter on the lower
housing of the module casing by a simple two-wire cable without any shielding; this
cable supplies both the data path and power supply to the slave nodes
simultaneously.
Contact needles pierce the cable through the cable insulation and make contact
with the copper conductors. When the cable is removed from the cable adaptor the
outer insulation of the cable self-seals the holes made by the cable adaptor
needles.
Figure 1-1 on page 10 shows the general layout and connections of the AS-i
Module.
Description Issue 01/03
MICROMASTER 411 & COMBIMASTER 411, AS-i Module Operating Instructions
10 6SE6400-5AT00-0BP0
Figure 1-1 View of the COMBIMASTER 411 & MICROMASTER 411 AS-i Module
Autres manuels pour MICROMASTER 411
2
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Siemens Unité de contrôle
Siemens
Siemens PSO 4000 Manuel utilisateur
Siemens
Siemens SINUMERIK 804D sl Guide de démarrage rapide
Siemens
Siemens SIMATIC NET RUGGEDCOM APE1808 Feuille d'instructions
Siemens
Siemens Simatic S7-300 Manuel utilisateur
Siemens
Siemens SINAMICS DCM Manuel utilisateur
Siemens
Siemens MJ-X Series Manuel utilisateur
Siemens
Siemens XC1003-A Mode d’emploi
Siemens
Siemens Simatic S7-1500 Manuel utilisateur
Siemens
Siemens LMS14 Manuel utilisateur
Siemens
Siemens MVS661 N Series Manuel utilisateur
Siemens
Siemens SIM-16RC Manuel utilisateur
Siemens
Siemens SiPass Driver Manuel utilisateur
Siemens
Siemens SED2-LONI/F Manuel utilisateur
Siemens
Siemens SIMOTION D4 5 Series Manuel utilisateur
Siemens
Siemens Logo! CM EIB Manuel utilisateur
Siemens
Siemens SIRIUS 3RT1.5 Manuel utilisateur
Siemens
Siemens MICROMASTER 420 Manuel utilisateur
Siemens
Siemens XDLC Manuel utilisateur
Siemens
Siemens SINUMERIK 840C Guide de configuration
Siemens
Siemens SIMATIC FM 353 Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
