Siemens FS-TRI-M Manuel utilisateur

SiemensBuilding Technologies, Inc.

FlorhamPark, New Jersey 07932

RED BLK ORG ORG GRN

EARTH

GND

TOCONTROL PANEL

ORPREVIOUS ADDRESSABLE DEVICE

MODEL: FS-TRI-M

REFER TO INSTL. INSTR.

P/N 315-699487

DEVICE ADDR.__________

ALLTERMINALS ARE POWERLIMITED

NOTE:

DO NOT USE

REAR CONDUIT ENTRY

SINGLE GANG

SWITCHBOX

(USER SUPPLIED)

SINGLE GANG

SWITCHPLATE (BLANK)

(USER SUPPLIED)

FS-TRI-M

UNDERWRITERS

LABORATORIES

The SIEMENS FS-TRI-M Contact Monitoring Module,

as shown in Figure 1, interfaces normally open contact

devices to an ddressable Device Circuit of a fire

alarm control unit.

The FS-TRI-M supports Style B (Class B) Initiating

Device Circuit wiring. Each module uses one address

on the ddressable Device Circuit. It does not require

any mechanical address programming. Use the FS-FPI

Programmer/Tester to program and test the module.

PROGRAMMING INSTRUCTIONS

CAUTION:

1. To prevent damage to the FS-FPI, do not

connect module to the FS-FPI until the

Addre able Device Circuit wiring i

di connected.

2. Only one device mu t be connected to the

FS-FPI at a time.

1. Connect the red and black wires of the FS-TRI-M

to the SIEMENS FS-FPI Programmer/Tester. Use

the cable provided with the Programmer/Tester

and the 2 alligator clips provided.

2. Set the address for the module by following the

instructions in the FS-FPI Programmer/Tester

Manual (P/N 315-699480).

3. Record the device address on the label located

on the module. The module can now be installed

and wired to the system.

MOUNTING

The FS-TRI-M mu t be in talled in a

UL Li ted electrical box.

Refer to Figure 2.

1. Connect the appropriate wires using wire nuts.

Tuck the FS-TRI-M module inside the electrical

box and dress the wiring as required.

2. Fasten the cover plate (user supplied) to the box.

Figure 2

FS-TRI-M Mounting

P/N 315-699487-1

Siemens Building Technologies, Inc.

8 ernwood Road

lorham Park, New Jersey 07932

Siemens Building Technologies, Ltd.

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 CN

Installation Instructions

Models FS-TRI-M

Contact Monitoring Module

Fire Safety

Figure 1

FS-TRI-M Module

Figure 3

FS-TRI-M Wiring

NOTES:

1. ll circuits are power limited.

2. In supervisory:

FS-TRI-M draws 1.5m

3. Initiating Device Circuit ratings:

Style B, Class B

See NFP 72 standard for the number of normally open contact devices allowed.

Voltage (max.): 5 VDC (during polling)

Supervisory current (max.): 0.5m (during polling)

larm current (max.): 0.8m (during polling)

IDC cable requirements:

Wire size: 18 to 14 WG

Wire resistance (max.): 2 ohms

Cable length (max.): 200 feet

Cable Type: Data grade, twisted pair

4. If Earth Ground is available, the green wire should be connected to earth ground.

5. If Earth Ground is NOT available, the IDC wiring should be limited to the same room.

RED

BLACK

GREEN

ORANGE

FS-TRI-M

-TO NEXT

ADDRESSABLE DEVICE

FROM ADDRESSABLE DEVICE

CIRCUIT OF A COMPATIBLE

CONTROL UNIT OR PREVIOUS

ADDRESSABLE DEVICE

GROUND

SEE NOTES 4 AND 5

END OF LINE RESISTOR

P/N 140-820185

3.6K, 1/4W, 5%

CONTACT DEVICE

INITIATING DEVICE CIRCUIT

SUPERVISED, SEE NOTE 3

ADDRESSABLE DEVICE CIRCUIT

24VDC NOMINAL, SUPERVISED

WIRING

Remove all y tem power before in tallation, fir t battery and then AC.

(To power up, connect AC first then battery.)

Refer to the wiring diagram and wire the module accordingly.

P/N 315-699487-1

Autres manuels Siemens Unité de contrôle

Siemens

Siemens CPU 412-5H Document technique

Siemens

Siemens 3RK1408-8K.00-0AA2 Manuel utilisateur

Siemens

Siemens LMU54 Series Manuel de l'opérateur

Siemens

Siemens PROFIBUS CP 1542-5 Manuel utilisateur

Siemens

Siemens VVP47 Series Manuel utilisateur

Siemens

Siemens SINUMERIK MC Guide de démarrage rapide

Siemens

Siemens SIRIUS ACT 3SU14 Manuel utilisateur

Siemens

Siemens SIMATIC ET 200S 4DI DC24V ST Manuel utilisateur

Siemens

Siemens SIMATIC FM 351 Manuel utilisateur

Siemens

Siemens SAFEDLINK Mode d’emploi

Siemens

Siemens SINAMICS G130 Manuel utilisateur

Siemens

Siemens Synco RMZ792 Manuel de l'opérateur

Siemens

Siemens FDCIO223 Manuel utilisateur

Siemens

Siemens SIPROCESS GA700 Manuel utilisateur

Siemens

Siemens SINUMERIK 808D Manuel utilisateur

Siemens

Siemens SIMOCODE pro Manuel utilisateur

Siemens

Siemens SCALANCE W788C-2 Manuel utilisateur

Siemens

Siemens RDM-MXL Manuel utilisateur

Siemens

Siemens SINAMICS G120 Manuel utilisateur

Siemens

Siemens SINUMERIK 840D sl Feuille d'instructions

Siemens

Siemens SINUMERIK 840C Guide de configuration

Siemens

Siemens SIMATIC RF170C Manuel utilisateur

Siemens

Siemens SIMATIC ET 200SP Manuel utilisateur

Siemens

Siemens P Series Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur