Sanus Systems HTB7 Manuel utilisateur

Assembly Instructions for model: HTB7 Speaker Stands

Thank you for choosing Vuepoint™ speaker stands. These stands are designed to support satellite speakers up to 4 lb. each.

If you have any questions regarding this or any other Sanus Systems product, please contact us at 800.359.5520 or visit

www.sanus.com. Check carefully to make sure you have all the parts listed below. Our customer service representatives

can quickly assist you with any issues regarding assembly or missing parts. Replacement parts for products purchased from

an authorized dealer will be shipped directly to you. Please call Sanus Systems before returning products to the point of

purchase.

Supplied Parts:

(2) Base - a (2) Lower Pillar - b (2) Upper Pillar Assembly - c

(2) Flat Head Bolt - d (2) Top Plate - e (2) Double Stick Pad - f

(2) L Bracket - g (2) Knob - h (2) Keyhole Bolt - i

(2) Double Bolt Bracket - j (4) 1/4 - 20 Speaker (2) M5 Speaker (6) Felt Pad - m

Attachment Bolt - k Attachment Bolt - l

Diagram 1

Sanus Systems 2221 Hwy 36 W, Saint Paul, MN 55113 04.15.05

Customer Service: 800.359.5520. See complimentary Sanus products at www.sanus.com

Step 1: Remove the backing and add 3 Felt Pads

(m) to the bottom of each Base (a) as shown in

Diagram 1 below.

Diagram 2 Diagram 3

Diagram 4 Diagram 5 Diagram 6 Diagram 7

Step 2: Thread the end of the Lower Pillar (b) with the Base Nut down into the Base (a). Tighten the Base Nut down onto

the Base as necessary, shown in Diagram 2.

NOTE: The pillars are hollow for speaker wire management purposes. If you would like to use the stands for wire

management, run the speaker wire up through the Base and the Lower Pillar. Next continue to run the wire through

the upper pillar assembly and out the oval hole in the back of the Upper Pillar before continuing onto Step 3.

WARNING: Speaker wire should be disconnected from the receiver or ampliﬁer when you run it through the center

of the speaker stand pillars.

Step 3: Slide the Upper Pillar Assembly (c) down into the Lower Pillar (b). Make sure the pole retaining ring is on the Up-

per Pillar under the plastic connector as shown in Diagram 3. Turn the plastic connector clockwise to hold the Upper Pillar

Assembly at any desired height.

b Upper Pillar

End of Lower Pillar with Plastic Connector

the Base Nut attached

Pole Retaining Ring

Step 4: Choose the appropriate speaker mount:

Single Bolt Double Bolt Keyhole Bottom Bolt

on Back on Back on Back / No Bolt

h d

d j d h d

g g g f

i e

k,l

c c c c

Place the Flat Head Bolt (d) down through either the L Bracket (g) or the Top Plate (e) depending on your speaker mount

attachment and thread it into the top of the Upper Pillar (c). Tighten the Flat Head Bolt with a philips screw driver.

NOTE: The bracket should be positioned so that the curve on the Upper Pillar allows the speaker to be centered over

the Lower Pillar.

Step 5: Attach your speakers.

NOTE: Hardware for the most common speakers is supplied. Other hardware may be required and can be found at

your local hardware store.

Single Bolt on Back: Place correct Speaker Attachment Bolts (k,l) through the L Bracket (g) and thread it into your speaker

so that your speaker hangs on the ﬂat side of the L Bracket as Shown in Diagram 4 above.

Double Bolt on Back: Attach the Double Bolt Bracket (j) to the L Bracket (g) with the Knob (h). Place the correct Speaker

Attachment Bolts (k) through the Double Bolt Bracket and thread them into the speaker as shown in Diagram 5 above.

Keyhole on Back: Insert the Keyhole Bolt (i) through the narrow opening on the L Bracket (g) and thread it into the Knob

(h). The head of the Keyhole Bolt should ﬁt into the keyhole opening on your speaker. Slide the speaker down on the Key-

hole Bolt and secure it to the stand by tightening the Knob as shown in Diagram 6 above.

Bottom Bolt / No Bolt: Remove the backing from one side of the Double Stick Pad (f) and attach it to the Top Plate (e) so

that the hole patterns in each part line up. Remove the backing from the other side of the Double Stick Pad. If the speaker has

a bottom bolt attachment make sure the threaded hole lines up with one of the slots in the Top Plate and fasten the speaker

with a Speaker Attachment Bolt (k,l). Press the speaker onto the pad. The Double Stick Pad will hold your speaker securely

in place as shown in Diagram 7 above.

Sanus Systems 2221 Hwy 36 W, Saint Paul, MN 55113 04.15.05

Customer Service: 800.359.5520. See complimentary Sanus products at www.sanus.com

Autres manuels pour HTB7

Table des matières

Autres manuels Sanus Systems Support et étagère

Sanus Systems

Sanus Systems PFV59S Guide d'installation

Sanus Systems

Sanus Systems VisionMount MT25 Manuel utilisateur

Sanus Systems

Sanus Systems FM37 Manuel utilisateur

Sanus Systems

Sanus Systems Monitor Mount VMTV Manuel utilisateur

Sanus Systems

Sanus Systems Motorized Mount LA112 Manuel utilisateur

Sanus Systems

Sanus Systems VMFL1 Manuel utilisateur

Sanus Systems

Sanus Systems VMCM1 Manuel utilisateur

Sanus Systems

Sanus Systems VisionMount VMA202 Manuel utilisateur

Sanus Systems

Sanus Systems Natural Foundations NF18 Manuel utilisateur

Sanus Systems

Sanus Systems HTSAT Manuel utilisateur

Sanus Systems

Sanus Systems VMPL50 Manuel utilisateur

Sanus Systems

Sanus Systems VisionMount VM200 Manuel utilisateur

Sanus Systems

Sanus Systems WMS3 Manuel utilisateur

Sanus Systems

Sanus Systems EFB Manuel utilisateur

Sanus Systems

Sanus Systems NEW FOUNDATIONS 500 Series Manuel utilisateur

Sanus Systems

Sanus Systems New Foundations 100 Series Manuel utilisateur

Sanus Systems

Sanus Systems VMCT Manuel utilisateur

Sanus Systems

Sanus Systems VM2 Manuel utilisateur

Sanus Systems

Sanus Systems Sanus VisionMount VMAA18 Manuel utilisateur

Sanus Systems

Sanus Systems VMUC1 Manuel utilisateur

Sanus Systems

Sanus Systems VMSA Manuel utilisateur

Sanus Systems

Sanus Systems VM2 Manuel utilisateur

Sanus Systems

Sanus Systems BF16 Manuel utilisateur

Sanus Systems

Sanus Systems Vision Mount VMBR Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur