Sanus Systems VMFL1 Manuel utilisateur

Assembly Instructions for Model: VMFL1

Thank you for choosing a Sanus Systems Vision Mount wall mount. The VMFL1 is designed to mount up to 30” LCD ﬂat panel televi-

sions weighing up to 40 lb to a vertical wall. It will allow the television to be just .5” from of the wall.

Safety Warning: If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualiﬁed

contractor or contact Sanus at 800.359.5520 or www.sanus.com. Check carefully to make sure that there are no missing or defective

parts. Our customer service representatives can quickly assist you with installation questions and missing or damaged parts. Replace-

ment parts for products purchased through authorized dealers will be shipped directly to you. Never use defective parts. Improper instal-

lation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly speciﬁed by Sanus Systems.

Sanus Systems can not be liable for damage or injury caused by incorrect mounting, incorrect assembly, or incorrect use. Please call

Sanus Systems before returning products to the point of purchase.

RequireTools: 3/8 drill bit, phillips screw driver

Supplied Parts and Hardware: Some parts not shown as actual size*

(1) Wall Plate - a* (1) Monitor Bracket - b*

(2) Lag Bolt - c (4) Dry Wall Anchor - d

(4) M4 x 10 mm Bolt - e (4) M4 x 20 mm Bolt - f (4) M4 x 30 mm Bolt - g (2) M5 Locking Bolt - h

(4) M4 Washer - i (4) Small M4 Spacer - j (4) Large M4 Spacer - k (2) M5 Spacer - l

Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 04.27.05

Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com

Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 04.27.05

Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com

Step 6: Attach Monitor Bracket to Wall Plate

Lift the TV up so the two hooks on the Monitor Bracket (b) align with the slits on the top of the Wall Plate (a). See the Detailed View of

Diagram 6 for assistance. Ensure the Monitor Bracket and Wall Plate are secured together by the top two hooks.

Note: Do not tighten Locking Bolts (h) at this point!

Diagram 6 Detailed View

hook

wall

tab

Step 7: Cable hook up and lock Monitor Bracket to Wall Plate

To allow for greater space between the wall and your display to install cables, allow the display to hang from the two top hooks on the

Monitor Bracket (b) with the bottom tabs free to move as shown in Diagram 7a. Once all cables are installed, make sure the top two

hooks and the bottom two tabs are engaged with the wall plate. See the Detailed View of Diagram 7b. Proceed to tighten the M5 Locking

Bolt (h) so the Monitor Bracket is secured to the Wall Plate.

Diagram 7a Diagram 7b Detailed View

a h

wall

Step 1: Hang Wall Plate

Wood Stud Mounting: First, determine the location of the Wall Plate (a) prior to installation. Use a high quality stud sensor to locate

a stud. Using the Wall Plate as a template and mark two holes in the apporpriate location. Make sure the hole is in the center area of

the stud. Attach the Wall Plate to the wall using two Lag Bolts (c). Make sure the Wall Plate is oriented so the ﬂat surface in the center

of the plate is against the wall as shown in Diagram 1a. Proceed to keyhole mount the Wall Plate onto the Lag Bolts. Tighten each Lag

Bolt ﬁrmly.

Drywall Installation: Position the Wall Plate in the desired location on the wall. Using the Wall Plate as a template, mark the location of

the four outer mounting holes. Using a 3/8”drill bit, proceed to drill a 3/8”pilot hole in each marked location. Install a Dry Wall Anchor

(d) in one of the pilot holes and tighten the anchor bolt until it is fully seated. See Diagram 1b. Loosen the anchor bolt approximately

1/4” and repeat process for the three additional pilot holes. Once Wall Plate is keyhole mounted onto the wall, proceed to tighten all 4

anchor bolts ﬁrmly.

Note: For Drywall Installations, make sure the Washer is inbetween the head of the anchor bolt and the Wall Plate.

Diagram 1a Diagram 1b

d drill 3/8” pilot hole

a drywall mounting holes

tighten anchor bolt until

the Anchor is pulled up

against the wall

Step 2: Install M5 Locking Bolts

Insert each M5 Locking Bolt (h) through a M5 Spacer (l) and thread it into the appropriate hole in the Monitor Bracket (b) as seen in the

Detailed View of Diagram 2. Thread the M5 Locking Bolt into the Monitor Bracket just enough to engage the threading.

Diagram 2 Detailed View

Note: For TVs that have a ﬂat back see Step 3. For TVs that have a recessed hole pattern, see Step 4. For TVs that have a deeply

recessed hole pattern, see Step 5.

Step 3: Attach Monitor Bracket to ﬂat back TV

To attach the Monitor Bracket (b) to the TV, simply insert a M4 x 10 mm Bolt (e) through the countersunk hole in the Monitor Bracket,

the M4 Washer (i) and thread it into the TV. Repeat process until all 4 bolts are secured to the TV. See the Detailed View of Diagram 3

for assistance. Proceed to tighten each bolt with a phillips screw driver.

Note: For installations where the hole pattern is recessed into the back of the TV, see Step 3 or Step 4.

Diagram 3 Detailed View

Step 4: Attach Monitor Bracket to a TV with a recessed hole pattern

To attach the Monitor Bracket (b) to the TV, simply insert a M4 x 20 mm Bolt (f) through the countersunk hole in the Monitor Bracket,

the Small M4 Spacer (j) and thread it into the TV. Repeat process until all 4 bolts are secured to the TV. See the Detailed View of Diagram

4 for assistance. Proceed to tighten each bolt with a phillips screw driver

Diagram 4 Detailed View

j b

Step 5: Attach Monitor Bracket to a TV with a deeply recessed hole pattern

To attach the Monitor Bracket (b) to the TV, simply insert a M4 x 30 mm Bolt (g) through the countersunk hole in the Monitor Bracket,

the Large M4 Spacer (k) and thread it into the TV. Repeat process until all 4 bolts are secured to the TV. See the Detailed View of Dia-

gram 5 for assistance. Proceed to tighten each bolt with a phillips screw driver.

Diagram 5 Detailed View

Autres manuels pour VMFL1

Table des matières

Autres manuels Sanus Systems Support et étagère

Sanus Systems

Sanus Systems New VisionMount VMA201 Manuel utilisateur

Sanus Systems

Sanus Systems VMSA Manuel utilisateur

Sanus Systems

Sanus Systems WMS5 Manuel utilisateur

Sanus Systems

Sanus Systems Vision Mount VMBR Manuel utilisateur

Sanus Systems

Sanus Systems Sanus Ultimate Foundations UF34 Manuel utilisateur

Sanus Systems

Sanus Systems VisionMount MF203 Manuel utilisateur

Sanus Systems

Sanus Systems STEEL FOUNDATIONS SFC Manuel utilisateur

Sanus Systems

Sanus Systems VM400 Manuel utilisateur

Sanus Systems

Sanus Systems PFFP Manuel utilisateur

Sanus Systems

Sanus Systems VM2 Manuel utilisateur

Sanus Systems

Sanus Systems Sanus VisionMount VMAA18 Manuel utilisateur

Sanus Systems

Sanus Systems VMCA9 Manuel utilisateur

Sanus Systems

Sanus Systems New Foundations 100 Series Manuel utilisateur

Sanus Systems

Sanus Systems HTSAT Manuel utilisateur

Sanus Systems

Sanus Systems SD115 Manuel utilisateur

Sanus Systems

Sanus Systems VisionMount ML22 Manuel utilisateur

Sanus Systems

Sanus Systems MF110 Manuel utilisateur

Sanus Systems

Sanus Systems VisionMount MF202 Manuel utilisateur

Sanus Systems

Sanus Systems VisionMount VM200 Manuel utilisateur

Sanus Systems

Sanus Systems HTB7 Manuel utilisateur

Sanus Systems

Sanus Systems SD103 Manuel utilisateur

Sanus Systems

Sanus Systems Sanus VisionMount LC1A Manuel utilisateur

Sanus Systems

Sanus Systems SANA1A Manuel utilisateur

Sanus Systems

Sanus Systems VisionMount MT25 Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur