Planet BSP-360 Manuel utilisateur
Industrial Renewable Power
5-Port Gigabit Managed Switch/Router
with 4-Port 802.3at PoE+
BSP-360
Quick Installation Guide
Safety Precautions
Please read the following before using:
1. All electrical work must be done in accordance with local, and/or international
electrical codes.
2. Before installing or using this device, read all instructions and cautionary
marking located in (or on) this guide, the controller, the batteries, PV (Photovol-
taic) array and any other device used.
3. To reduce the risk of short-circuits, use insulated tools when installing or working
with the inverter, the controller, the batteries, or any DC source (e.g., PV).
4. Remove all jewelry. This will greatly reduce the chance of accidental exposure to
live circuits.
5. The controller contains more than one live circuit (batteries and PV array).
Power may be present at more than one source.
6. This product contains no user serviceable parts. Do not attempt to repair this
unit unless fully qualied.
Table of Contents
1. Package Contents ....................................................................................... 4
2. Requirements ............................................................................................. 5
3. Hardware Introduction ................................................................................ 6
3.1 Front Panel ......................................................................................... 6
3.2 LED Indicators..................................................................................... 7
3.3 Upper Panel ........................................................................................ 8
4. Hardware Installation .................................................................................10
5. Web Management ......................................................................................16
6. [OPTIONAL] Deployed Devices Monitored via NMS-360 Controller ..................18
7. Customer Support .....................................................................................20
Appendix A: Recommended Use of the Connected Wires....................................21
Appendix B: Recommended Settings for Batteries..............................................22
Appendix C: Battery Default ............................................................................23
4
1. Package Contents
Thank you for purchasing PLANET Industrial Renewable Energy Managed PoE
Switch/Router, BSP-360. Open the box of the BSP-360 and carefully unpack it. The
box should contain the following items:
1 x BSP-360 1 x Quick Installation Guide
1 x Wall Mounting Kit 1 x DIN-rail Kit 5 x RJ45 Dust Cap
If any of these are missing or damaged, please contact your dealer immediately. If
possible, retain the carton including the original packing materials to enable you to
repack the product in case there is a need to return it to us for repair.
5
2. Requirements
PLANET BSP-360 provides a remote login interface for management purposes. The
following equipment is necessary for further management:
Workstation is installed with Ethernet NIC (Network Interface Card)
Choice of Internet browsers includes Windows XP/2003, Vista, Windows 7,
Windows 8, Windows 10, Windows 11, MAC OS X, Linux, Fedora, Ubuntu or
other platforms compatible with TCP/IP protocols.
The above workstation is installed with Web browser and JAVA runtime envi-
ronment plug-in.
Ethernet Port connection
Use standard network (UTP) cables with RJ45 connectors.
PV and battery
Two 12V lithium or lead-acid batteries connected in series or one 24V lithium
or lead-acid battery.
The maximum operating voltage of PV is 45V.
Note
It is recommended to use Chrome 98.0.xxx or above to access the
BSP-360.
6
3. Hardware Introduction
3.1 Front Panel
The front panel of the BSP-360 consists of 5 auto-sensing 10/100/1000Mbps
Ethernet RJ45 ports and one USB interface. The LED Indicators are also located on
the RJ45 ports of the BSP-360.
V1+
Reset
V2+
BSP-360
PWR Alarm PV System
50W 100W 120W
1
2
3
4
5/WAN
PoE Power
Usage
ACTLNK
PoE-in-Use
Industrial Renewable Energy Managed PoE+Switch/Router
DC Ouput: 24V , 2A max.
1
2
3
4
5
Figure 3-1 Front Panel of BSP-360
Item Interface Description
1Port-1~Port-4 4 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports with
802.af/at PoE+ injector function.
2Port-5
One 10/100/1000BASE-T RJ45 auto-MDI/MDI-X port.
Port-5 functions as WAN port when the operation
mode of BSP-360 is congured to “Gateway mode”.
3USB Connect the USB storage to USB port and back up the
conguration le.
4Reset Button < 5 seconds: System reboot.
> 10 seconds: Factory default.
54-pin Terminal
Block
2 x 24V 2A DC output connector.
The output voltage is the same as battery voltage.
Maximum power output is clamped at 48W.
7
3.2 LED Indicators
System
LED Color Function
PWR Green On To indicate BSP-360 has power.
Alarm Red
Slow
Blinks To indicate PV < 24V.*
Fast
Blinks To indicate battery voltage is ≤ LVD.*
PV
System Green
Slow
Blinks To indicate the system is “Not Charging”.
Fast
Blinks To indicate the battery is “Charging”.
50W Amber On To indicate the system consumes over 50-watt
PoE power budget.
100W Amber On To indicate the system consumes over 100-watt
PoE power budget.
120W Amber On To indicate the system consumes a total
120-watt PoE power budget.
* The detection voltage will have a tolerance of ±0.7V.
PoE 10/100/1000BASE-T Interfaces (Port-1 to Port-4)
LED Color Function
LNK/ACT Green Blinks To indicate the link through that port is
successfully established.
PoE Amber
Lights To indicate the port is providing DC in-line power.
O To indicate the connected device is not a PoE
Powered Device (PD).
10/100/1000BASE-T Interfaces (Port-5)
LED Color Function
LNK/ACT Green Blinks To indicate the link through that port is
successfully established.
8
3.3 Upper Panel
The upper panel of the BSP-360 consists of one terminal block connector with PV
and battery power inputs.
Battery DC Input: 24V , 10A
PV DC Input: 24-45V , 8.8A max.
Max.
Fault
Alarm Loading: 24V, 1A
V+
PV Bat.
Alarm
V+
Warning
Please make sure the V+ & V is connected correctly,
and the wire gauge meets the maximum current.
1 2 3 4 5 6
Figure 3-2 Upper Panel
The input voltage range of each interface is shown as follows:
PV In Connector
24~45V DC
Battery DC Input: 24V
, 10A
PV DC Input: 24- 45V
, 8.8A max.
Max.
Fault
Alarm Loadin g: 24V, 1A
V+
PV Bat.
Alar m
V+
Warning Please make sure the V+ & V is c onnected correctly,
and the wire gauge meets the maximum current.
1 2 3 4 5 6
Solar PV
24~45V DC
DC
DC
9
Battery In/Out
24V DC
Battery DC Input: 24V
, 10A
PV DC Input: 24- 45V
, 8.8A max.
Max.
Fault
Alarm Loadin g: 24V, 1A
V+
PV Bat.
Alar m
V+
Warning Please make sure the V+ & V is c onnected correctly,
and the wire gauge meets the maximum current.
1 2 3 4 5 6
Battery
24V DC
DC
DC
Note
The wire gauge for the terminal block should be in the range from
16 to 20 AWG.
Fault Alarm Connectors
The fault alarm contacts are in the middle (3 & 4) of the terminal block connector
as the picture shows below. Inserting the wires, the Renewable Energy Switch will
detect the fault status of the power failure.
*When the system is “ON”, the fault alarm is “o”.
*When the system is “OFF”, the fault alarm will “trigger”.
1 2 3 4 5 6
Load
5~24VDC
GND
10
4. Hardware Installation
The following section describes the hardware installation of the BSP-360. Before
connecting any network device to the BSP-360, read this chapter carefully.
BSP-360
DC
DC
BatteryCAM1 CAM2 CAM3
Outdoor
Wireless AP
PoE PoE
PoE
PoE
Media Converter/
DC Powered Device
Solar PV
DC
DC
Power Line (DC)
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
2.4GHz 802.11n
N
N
1000BASE-SX/LX Fiber Optic
1000
1000
Ethernet Switch
Monitoring Center
Please follow the following steps to install the system:
Step 1. Installing BSP-360
Place the BSP-360 in a desired location using the wall-mount or Din-rail xtures.
Note
a. Please install the BSP-360 in a proper enclosure or shelter.
b. The BSP-360 must be grounded.
Table des matières
Autres manuels Planet Changer
Planet
Planet GS-5220-8P2T2S Manuel utilisateur
Planet
Planet IGS-504HPT Manuel utilisateur
Planet
Planet WSD-800 Manuel utilisateur
Planet
Planet FNSW-2401CS Manuel utilisateur
Planet
Planet GS-6320-8P2X Manuel utilisateur
Planet
Planet IGS-6325 Series Manuel utilisateur
Planet
Planet IPM-8221 Manuel utilisateur
Planet
Planet GSD-604HP Manuel utilisateur
Planet
Planet FGSW-4840S Manuel utilisateur
Planet
Planet IGS-6325-4T2X Manuel utilisateur
Planet
Planet FSD-624SF Manuel utilisateur
Planet
Planet FSD-1605 Manuel utilisateur
Planet
Planet GSW-1601 Manuel utilisateur
Planet
Planet WGSW-24040 Manuel utilisateur
Planet
Planet GSD-802PS Manuel utilisateur
Planet
Planet IGS-5225-4T2S Manuel utilisateur
Planet
Planet SOHOConnect DHD-801 Manuel utilisateur
Planet
Planet IGSW-24040T Manuel utilisateur
Planet
Planet GS-5220-8UP2T2X Manuel utilisateur
Planet
Planet FGSW-262 Manuel utilisateur
