Pilz PSSu E F PS2 Manuel utilisateur
PSSu E F PS2(-T)(-R)
Operating Manual-1002237-EN-05
}Decentralised system PSSuniversal I/O
Preface
This document is a translation of the original document.
All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made
for internal purposes. Suggestions and comments for improving this documentation will be
gratefully received.
Source code from third-party manufacturers or open source software has been used for
some components. The relevant licence information is available on the Internet on the Pilz
homepage.
Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,
SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks
of Pilz GmbH & Co. KG in some countries.
SD means Secure Digital
Contents
Operating Manual PSSu E F PS2(-T)(-R)
1002237-EN-05 3
Section 1 Introduction 5
1.1 Validity of documentation 5
1.1.1 Retaining the documentation 5
1.1.2 Terminology: System environment A and B 5
1.2 Definition of symbols 6
Section 2 Overview 7
2.1 Module structure 7
2.2 Module features 7
2.3 Front view 8
Section 3 Safety 10
3.1 Intended use 10
3.2 Safety regulations 11
3.2.1 Use of qualified personnel 11
3.2.2 Warranty and liability 11
3.2.3 Disposal 11
Section 4 Function description 12
4.1 Block diagram 12
4.2 Module features 12
4.2.1 Supply voltage 12
4.2.1.1 Current load capacity 13
4.2.2 Integrated protection mechanisms 14
4.3 Configuration 14
Section 5 Installation 15
5.1 General installation guidelines 15
5.1.1 Dimensions 15
5.2 Installing the base module 16
5.3 Inserting and removing an electronic module 17
5.3.1 Inserting an electronic module 18
5.3.2 Removing an electronic module 19
5.3.3 Changing an electronic module during operation 19
Section 6 Wiring 20
6.1 General wiring guidelines 20
6.1.1 Mechanical connection of the base modules 20
6.2 Terminal configuration 22
6.3 Connecting the module 24
Section 7 Operation 25
7.1 Messages 25
7.2 Display elements 25
7.2.1 Display elements for module diagnostics 25
7.2.2 Display elements for the status of the module supply and periphery supply 26
Contents
Operating Manual PSSu E F PS2(-T)(-R)
1002237-EN-05 4
Section 8 Technical details 27
Section 9 Order reference 31
9.1 Product 31
9.2 Accessories 31
Introduction
Operating Manual PSSu E F PS2(-T)(-R)
1002237-EN-05 5
1 Introduction
1.1 Validity of documentation
This documentation is valid for the product types PSSu E F PS2, PSSu E F PS2-T and
PSSu E F PS2-R. It is valid until new documentation is published.
This operating manual explains the function and operation, describes the installation and
provides guidelines on how to connect the product.
1.1.1 Retaining the documentation
This documentation is intended for instruction and should be retained for future reference.
1.1.2 Terminology: System environment A and B
The PSSu system can be used in two different system environments. The module's applic-
ation area is described in the chapter "Intended Use" of the manual.
The distinction is made between
}PSSu in system environment A
}PSSu in system environment B
The distinction is based on the application area of the PSSu system.
PSSu in system environment A may be used in the
}Decentralised system PSSu I/O
}Not in the automation system PSS 4000
PSSu in system environment B may be used in the
}Automation system PSS 4000, e.g. with
– Decentralised system PSSu I/O with SafetyNET p
– Control system PSSu PLC
– Control system PSSu multi
The modules PSSu E F PS2 and PSSu E F PS2(-T)(-R) are exclusively for use in system
environment B (automation system PSS 4000).
Introduction
Operating Manual PSSu E F PS2(-T)(-R)
1002237-EN-05 6
1.2 Definition of symbols
Information that is particularly important is identified as follows:
DANGER!
This warning must be heeded! It warns of a hazardous situation that poses
an immediate threat of serious injury and death and indicates preventive
measures that can be taken.
WARNING!
This warning must be heeded! It warns of a hazardous situation that could
lead to serious injury and death and indicates preventive measures that can
be taken.
CAUTION!
This refers to a hazard that can lead to a less serious or minor injury plus
material damage, and also provides information on preventive measures
that can be taken.
NOTICE
This describes a situation in which the product or devices could be dam-
aged and also provides information on preventive measures that can be
taken. It also highlights areas within the text that are of particular import-
ance.
INFORMATION
This gives advice on applications and provides information on special fea-
tures.
Overview
Operating Manual PSSu E F PS2(-T)(-R)
1002237-EN-05 7
2 Overview
2.1 Module structure
A module consists of
}Electronic module and
}Base module with
– Screw terminals or
– Cage clamp terminals
The base modules are the carrier units for the electronic modules and are used to connect
the field wiring. The electronic modules are inserted on to the base modules and determine
the module's function.
Details of the base modules that can be used are available in the chapter entitled “Intended
Use”.
2.2 Module features
The product has the following features:
}Current load capacity of module supply [max. 1 A
}When the supply voltage is interrupted, the module supply is buffered for 20ms.
}Separate infeed for periphery supply
}Separate infeed for module supply
}Infeed for C-rail supply
}Potential isolation from module supply
}High EMC immunity
}LEDs for:
– Module supply
– Periphery supply
– Module error
}T-type:
PSSu E F PS2-T: for increased environmental requirements
}R-type:
PSSu E F PS2-R: for railway applications
Overview
Operating Manual PSSu E F PS2(-T)(-R)
1002237-EN-05 8
2.3 Front view
2111
2212
2313
Err
11 21
12
0V
22
0V
13 23
14
C
24
C
PSSu E F
PS2
5 V 24V
0V24V
24V 24V
2414
PSSu E F
PS2
312192
100000
001
1
3
8
7
4
5
6
10
2
11
9
A
B
Key:
}A: Electronic module
}B: Base module
}1: LED for module diagnostics
}2: Labelling strip with:
– Name of electronic module
– Order number
– Serial number
– Hardware version number
– 2D code
}3: Labelling strip for the terminal configuration on the base module
}4: Name of electronic module
}5: Connection level 1
}6: Connection level 2
}7: Connection level 3
}8: Connection level 4
Overview
Operating Manual PSSu E F PS2(-T)(-R)
1002237-EN-05 9
}9: Square mounting holes (connection levels 1, 2, 3 and 4)
– With screw to loosen/tighten the screw terminal on base modules with screw termin-
als
– With mechanism to operate the cage clamp on base modules with cage clamp ter-
minals
}10: Round connection holes (connection levels 1, 2, 3 and 4) for connecting the signal
lines
}11: Mounting slot for colour marker to label the connection level (connection levels 1, 2,
3 and 4)
Safety
Operating Manual PSSu E F PS2(-T)(-R)
1002237-EN-05 10
3 Safety
3.1 Intended use
The module may be used in system environment B (automation system PSS 4000).
The modules PSSu E F PS2 and PSSu E F PS2-T may be used as a safety components in
accordance with the Lifts Directive 95/16/EC in accordance with the requirements of
EN81-1/2:1998+A3:2009, EN81-20:2015, EN81-50:2015, EN81-22:2014 and
EN115-1:2008+A1:2010.
The programmable safety system should be installed in a protected environment that meets
at least the requirements of pollution degree 2. Example: Protected inside space or control
cabinet with protection class IP54 and corresponding air conditioning.
The module has high immunity and is suitable for use in an industrial environment with a
strong electromagnetic field.
The module provides the supply for the module supply and periphery supply within the sys-
tem.
The module may be used as:
}Supply module to refresh the module supply and periphery supply
}Supply module to form supply groups
The module PSSu E F PS2-T is suitable for use where there are increased environmental
requirements (see Technical Details).
The module PSSu E F PS2-R is suitable for use where there are increased environmental
requirements demanded by railway applications (see Technical details).
When using the module for railway applications, a mains filter should be connected up-
stream in order to comply with the limit values for conducted high frequency interference
voltages on the supply voltage connections, in accordance with EN 50121-4. The mains fil-
ter must have suitable properties, such as the Schaffner mains filter, type FN2070-3.
Intended use includes making the electrical installation EMC-compliant. Please refer to the
guidelines stated in the "PSSuniversal Installation Manual". The module is designed for use
in an industrial environment. It is not suitable for use in a domestic environment, as this can
lead to interference.
The following is deemed improper use in particular:
}Any component, technical or electrical modification to the module
}Use of the module outside the areas described in this manual
}Any use of the module that is not in accordance with the technical details.
INFORMATION
The module is supported by PAS4000 from version 1.3.0. We recommend
that you always use the latest version (download from www.pilz.com).
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Pilz Unité de contrôle
Pilz
Pilz PNOZ mo2p Manuel utilisateur
Pilz
Pilz PIT si1.1 Manuel utilisateur
Pilz
Pilz PSS Series Manuel utilisateur
Pilz
Pilz PSSu E S 2AI RTD Manuel utilisateur
Pilz
Pilz PNOZ m ES ETH Manuel utilisateur
Pilz
Pilz PNOZ mi1p Manuel utilisateur
Pilz
Pilz PITmode flex visu Manuel utilisateur
Pilz
Pilz PNOZ mc3p Manuel utilisateur
Pilz
Pilz PNOZ mc1p Manuel utilisateur
Pilz
Pilz PNOZ mi1p Manuel utilisateur
Pilz
Pilz PSS u2 ES 8DI Manuel utilisateur
Pilz
Pilz PNOZ mc10p Manuel utilisateur
Pilz
Pilz PIT m3.3p Manuel utilisateur
Pilz
Pilz PNOZ mc1p Manuel utilisateur
Pilz
Pilz ms3p HTL Manuel utilisateur
Pilz
Pilz PMCprotego S1--2 Manuel utilisateur
Pilz
Pilz P2HZ X1.10P Manuel utilisateur
Pilz
Pilz PSSu E AI SHT2 Manuel utilisateur
Pilz
Pilz PSEN cs 4.2p/M12 Manuel utilisateur
Pilz
Pilz PZE 9P Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
