Pilz PSSu E AI SHT2 Manuel utilisateur

PSSu E AI SHT2

Operating Manual 1003113-EN-02

}Decentralised system PSSuniversal I/O

Preface

This document is a translation of the original document.

All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made

for internal purposes. Suggestions and comments for improving this documentation will be

gratefully received.

Source code from third-party manufacturers or open source software has been used for

some components. The relevant licence information is available on the Internet on the Pilz

homepage.

Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,

SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks

of Pilz GmbH & Co. KG in some countries.

SD means Secure Digital

Contents

Operating Manual PSSu E AI SHT2

1003113-EN-02 3

Section 1 Introduction 4

1.1 Validity of documentation 4

1.1.1 Retaining the documentation 4

1.1.2 Terminology: System environment A and B 4

1.2 Definition of symbols 5

Section 2 Overview 6

2.1 Module structure 6

2.2 Module features 6

2.3 Front view 7

Section 3 Safety 9

3.1 Intended use 9

3.2 Safety regulations 10

3.2.1 Use of qualified personnel 10

3.2.2 Warranty and liability 10

3.2.3 Disposal 10

Section 4 Function Description 11

4.1 Block diagram 11

4.2 Module features 11

4.2.1 Functions 11

Section 5 Installation 13

5.1 General installation guidelines 13

5.1.1 Dimensions 13

5.2 Installing the base module 14

5.3 Inserting and removing an electronic module 15

5.3.1 Inserting an electronic module 16

5.3.2 Removing an electronic module 17

5.3.3 Changing an electronic module during operation 17

Section 6 Wiring 18

6.1 General wiring guidelines 18

6.1.1 Mechanical connection of the base modules 18

6.2 Terminal configuration 20

6.3 Connecting the module 23

Section 7 Technical details 24

Section 8 Order reference 26

8.1 Product 26

8.2 Accessories 26

Introduction

Operating Manual PSSu E AI SHT2

1003113-EN-02 4

1 Introduction

1.1 Validity of documentation

This documentation is valid for the product type E AI SHT2. It is valid until new documenta-

tion is published.

This operating manual explains the function and operation, describes the installation and

provides guidelines on how to connect the product.

1.1.1 Retaining the documentation

This documentation is intended for instruction and should be retained for future reference.

1.1.2 Terminology: System environment A and B

The PSSu system can be used in two different system environments. The module's applic-

ation area is described in the chapter "Intended Use" of the manual.

The distinction is made between

}PSSu in system environment A

}PSSu in system environment B

The distinction is based on the application area of the PSSu system.

PSSu in system environment A may be used in the

}Decentralised system PSSu I/O

}Not in the automation system PSS 4000

PSSu in system environment B may be used in the

}Automation system PSS 4000, e.g. with

– Decentralised system PSSu I/O with SafetyNET p

– Control system PSSu PLC

– Control system PSSu multi

Introduction

Operating Manual PSSu E AI SHT2

1003113-EN-02 5

1.2 Definition of symbols

Information that is particularly important is identified as follows:

DANGER!

This warning must be heeded! It warns of a hazardous situation that poses

an immediate threat of serious injury and death and indicates preventive

measures that can be taken.

WARNING!

This warning must be heeded! It warns of a hazardous situation that could

lead to serious injury and death and indicates preventive measures that can

be taken.

CAUTION!

This refers to a hazard that can lead to a less serious or minor injury plus

material damage, and also provides information on preventive measures

that can be taken.

NOTICE

This describes a situation in which the product or devices could be dam-

aged and also provides information on preventive measures that can be

taken. It also highlights areas within the text that are of particular import-

ance.

INFORMATION

This gives advice on applications and provides information on special fea-

tures.

Overview

Operating Manual PSSu E AI SHT2

1003113-EN-02 6

2 Overview

2.1 Module structure

A module consists of

}Electronic module and

}Base module with

– Screw terminals or

– Cage clamp terminals

The base modules are the carrier units for the electronic modules and are used to connect

the field wiring. The electronic modules are inserted on to the base modules and determine

the module's function.

Details of the base modules that can be used are available in the chapter entitled “Intended

Use”.

2.2 Module features

The product has the following features:

}1 analogue current input

Current range:

0 ... 0.2 A, single-pole, referenced to earth

}2 analogue current outputs

Current range:

0 .. 20mA, single-pole, referenced to earth

– Scaling of input current 1:10 and 1:20

– Evaluation via analogue input module with an input resistance = 115Ohm, (e.g.

PSSuEFAI I), order no.: 312 260)

}For standard and failsafe applications in system environment A and B

Overview

Operating Manual PSSu E AI SHT2

1003113-EN-02 7

2.3 Front view

Legend:

}A: Electronic module

}B: Base module

}1: Labelling strip with:

– Name of electronic module

– Order number

– Serial number

– Hardware version number

– 2D code

}2: Labelling strip for the terminal configuration on the base module

}3: Name of electronic module

}4: Connection level 1

}5: Connection level 2

}6: Connection level 3

}7: Connection level 4

Overview

Operating Manual PSSu E AI SHT2

1003113-EN-02 8

}8: Square mounting holes (connection levels 1, 2, 3 and 4)

– With screw to loosen/tighten the screw terminal on base modules with screw termin-

als

– With mechanism to operate the cage clamp on base modules with cage clamp ter-

minals

}9: Round connection holes (connection levels 1, 2, 3 and 4) for connecting the signal

lines

}10: Mounting slot for colour marker to label the connection level (connection levels 1, 2,

3 and 4)

Safety

Operating Manual PSSu E AI SHT2

1003113-EN-02 9

3 Safety

3.1 Intended use

The module provides shunts to scale the current for analogue inputs. The module may be

used in conjunction with analogue current inputs (e.g. PSSuEFAII, order no.: 312 260).

The module may be used for standard applications in system environment A and B.

Intended use includes making the electrical installation EMC-compliant. Please refer to the

guidelines stated in the "PSSuniversal Installation Manual". The module is designed for use

in an industrial environment. It is not suitable for use in a domestic environment, as this can

lead to interference.

The following is deemed improper use in particular:

}Any component, technical or electrical modification to the module

}Use of the module outside the areas described in this manual

}Any use of the module that is not in accordance with the technical details.

The E AI SHT2 module may be used in conjunction with the following base modules:

}PSSu BP 1/8 S

}PSSu BP 1/8 C

}PSSu BP 1/12 S

}PSSu BP 1/12 C

}PSSu BP-C 1/8 S

}PSSu BP-C 1/8 C

}PSSu BP-C 1/12 S

}PSSu BP-C 1/12 C

Safety

Operating Manual PSSu E AI SHT2

1003113-EN-02 10

3.2 Safety regulations

3.2.1 Use of qualified personnel

The products may only be assembled, installed, programmed, commissioned, operated,

maintained and decommissioned by competent persons.

A competent person is someone who, because of their training, experience and current pro-

fessional activity, has the specialist knowledge required to test, assess and operate the

work equipment, devices, systems, plant and machinery in accordance with the general

standards and guidelines for safety technology.

It is the company’s responsibility only to employ personnel who:

}Are familiar with the basic regulations concerning health and safety / accident preven-

tion

}Have read and understood the information provided in this description under "Safety"

}And have a good knowledge of the generic and specialist standards applicable to the

specific application.

3.2.2 Warranty and liability

All claims to warranty and liability will be rendered invalid if

}The product was used contrary to the purpose for which it is intended

}Damage can be attributed to not having followed the guidelines in the manual

}Operating personnel are not suitably qualified

}Any type of modification has been made (e.g. exchanging components on the PCB

boards, soldering work etc.).

3.2.3 Disposal

}In safety-related applications, please comply with the mission time TM in the safety-re-

lated characteristic data.

}When decommissioning, please comply with local regulations regarding the disposal of

electronic devices (e.g. Electrical and Electronic Equipment Act).

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Pilz Unité de contrôle

Pilz

Pilz PSSu E F 2DI 60-R Manuel utilisateur

Pilz

Pilz PIT es Set10u-5ns (AIDA) basic Manuel utilisateur

Pilz

Pilz PNOZ mi1p Manuel utilisateur

Pilz

Pilz PSSu E F 4DI-T Manuel utilisateur

Pilz

Pilz PNOZ m ES ETH Manuel utilisateur

Pilz

Pilz PSS Series Manuel utilisateur

Pilz

Pilz PNOZ mc4p Manuel utilisateur

Pilz

Pilz PIT js2 Manuel utilisateur

Pilz

Pilz Motion Control PMC Manuel utilisateur

Pilz

Pilz PSSu K S 16DO 0.5 Manuel utilisateur

Pilz

Pilz PSS u2 ES 4DOD 0.5A Manuel utilisateur

Pilz

Pilz PNOZ ms4p Manuel utilisateur

Pilz

Pilz PNOZ m EF 4DI4DOR Manuel utilisateur

Pilz

Pilz PNOZ m ES ETH Manuel utilisateur

Pilz

Pilz PNOZ ma1p Manuel utilisateur

Pilz

Pilz PSSu K F FAU B Manuel utilisateur

Pilz

Pilz PNOZ p1vp Manuel utilisateur

Pilz

Pilz PSSu E F 2DO 2 Manuel utilisateur

Pilz

Pilz P1HZ X1 Manuel utilisateur

Pilz

Pilz PNOZ m EF 16DI Manuel utilisateur

Pilz

Pilz PIT es Set/1 Manuel utilisateur

Pilz

Pilz PNOZ mmc1p Manuel utilisateur

Pilz

Pilz PSSu E S 2AI RTD Manuel utilisateur

Pilz

Pilz PSEN cs5.1p Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur