Patton electronics NetLink 1082 Manuel utilisateur

USER

MANUAL

MODEL 1082 and

1082/144

iDSL Modem with

V.34 or X.21 Interface

SALES OFFICE

(301) 975-1000

TECHNICAL SUPPORT

(301) 975-1007

Part# 07M1082/C-B

Doc# 033151UB

Revised 2/19/03

An ISO-9001

Certiﬁed

Company

CERTIFIED

TABLE OF CONTENTS

1.0 Warranty Information ................................................................. 4

1.1 FCC Information ........................................................................... 4

1.2 CE Notice...................................................................................... 4

1.3 Service.......................................................................................... 5

2.0 General Information.................................................................... 6

2.1 Features........................................................................................ 6

2.2 Description.................................................................................... 6

2.3 1082 SNMP Management Solutions............................................. 7

HTTP/HTML Management ........................................................... 7

3.0 Configuration .............................................................................. 8

3.1 Configuring the Hardware DIP Switches ...................................... 8

Configuring DIP Switch S1........................................................... 9

Switches S1-1 and S1-2: Data Rate........................................... 10

Switch S1-3: Data Set Ready during Line Loopback Test.......... 10

Switch S1-4: Must be set to the ON position (Reserved)........... 11

Switch S1-5: Asynchronous/Sync Operation.............................. 11

Switches S1-6 and S1-7: System Clock Mode........................... 11

Switch S1-8: Response to RDL Request.................................... 11

Configuring DIP switch S2.......................................................... 12

Switches S2-1: 19.2 kbps or 144 kbps Synchronous

Rate Enable................................................................................ 13

Switch S2-2: Front Panel Switch Disable................................... 13

Switches S2-3: Response to Local Line Loop

Requests from DTE.................................................................... 13

Switches S2-4 and S2-5: Not Assigned...................................... 13

Switch S2-6: Response to RDL Request from DTE................... 14

Switch S2-7: Compatability Mode............................................... 14

Switch S2-8: Not Assigned......................................................... 14

4.0 Installation................................................................................. 15

4.1 Connecting the Twisted Pair Interface........................................ 15

4.2 Connecting the Model 1082 (V.35) Serial Interface.................... 16

Connecting the Model 1082 (V.35) to a DTE Device.................. 16

Connecting the Model 1082 (V.35) to a DCE Device................. 16

4.3 Connecting the Model 1082 (X.21) Serial Interface.................... 17

Connecting the Model 1082 (X.21) to a “DCE” or

“DTE” Device.............................................................................. 17

Opening the Case....................................................................... 18

4.4 Connecting Power ...................................................................... 19

Universal AC Power (100–240VAC)........................................... 19

DC Power................................................................................... 20

5.0 Operation................................................................................... 21

5.1 Power-up .................................................................................... 21

5.2 LED Status Monitors................................................................... 21

5.3 Test Modes................................................................................. 22

Local Line Loopback (LLB)......................................................... 22

Remote Digital Loopback (RDL)................................................. 23

Using the V.52 (BER) test pattern generator.............................. 24

A Model 1082 Specifications....................................................... 25

A.1 Transmission Format ................................................................... 25

A.2 Transmission Line ....................................................................... 25

A.3 Clocking ...................................................................................... 25

A.4 Distance ...................................................................................... 25

A.5 Data Rates .................................................................................. 25

A.6 Diagnostics ................................................................................. 25

A.7 LED Status Indicators ................................................................. 25

A.8 Connectors ................................................................................. 26

A.9 Power .......................................................................................... 26

A.10 Temperature Range .................................................................... 26

A.11 Altitude ........................................................................................ 26

A.12 Humidity ...................................................................................... 26

A.13 Dimensions ................................................................................. 26

A.14 Weight ......................................................................................... 26

A.15 Line Interface .............................................................................. 26

B Model 1082C and 1082D Factory Replacement Parts and

Accessories............................................................................... 27

C Model 1082C and 1082D Interface Pin Assignments............. 28

D Model 1082C and 1082D Interface Pin Assignments............. 29

E Model 1082C and 1082D Interface Pin Assignment............... 30

1.0 WARRANTY INFORMATION

Patton Electronics

warrants all Model 1082 and Model 1082/144 com-

ponents to be free from defects, and will—at our option—repair or

replace the product should it fail within one year from the ﬁrst date of

shipment.

This warranty is limited to defects in workmanship or materials, and does

not cover customer damage, abuse or unauthorized modiﬁcation.If this

product fails or does not perform as warranted, your sole recourse shall

be repair or replacement as described above.Under no condition shall

Patton Electronics

be liable for any damages incurred by the use of this

product.These damages include, but are not limited to, the following:lost

proﬁts, lost savings and incidental or consequential damages arising

from the use of or inability to use this product.

Patton Electronics

spe-

ciﬁcally disclaims all other warranties, expressed or implied, and the

installation or use of this product shall be deemed an acceptance of

these terms by the user.

1.1 FCC INFORMATION

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules.These limits

are designed to provide reasonable protection against harmful interfer-

ence when the equipment is operated in a commercial environment.This

equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications.Operation of this

equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his own

expense.If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected

1.2 CE NOTICE

The CE symbol on your Patton Electronics equipment indicates that it is in

compliance with the Electromagnetic Compatibility (EMC) directive and

the LowVoltage Directive (LVD) of the Union European (EU). A Certiﬁcate

of Compliance is available by contacting Patton Technical Support.

1.3 SERVICE

All warranty and non-warranty repairs must be returned freight prepaid

and insured to Patton Electronics. All returns must have a Return Materi-

als Authorization number on the outside of the shipping container.This

number may be obtained from Patton Electronics Technical Service at:

Tel:

(301) 975-1007

E-mail:

[email protected]

URL:

www.patton.com

Note

Packages received without an RMA number will not be

accepted.

Patton Electronics’ technical staff is also available to answer any ques-

tions that might arise concerning the installation or use of your

Model 1082 or Model 1082/144.Technical Service hours:

8AM

5PM

EST

Monday

through

Friday

2.0 GENERAL INFORMATION

Thank you for your purchase of this

Patton Electronics

product.This

product has been thoroughly inspected and tested and is warranted for

OneYear parts and labor. If any questions or problems arise during

installation or use of this product, please do not hesitate to contact

Patton ElectronicsTechnical Support

(301) 975-1007

2.1 FEATURES

• Synchronous data rates: 19.2, 32, 56, 64, 128, and 144* kbps

• Asynchronous data rates: 0–38.4 kbps

• Full duplex operation over a single twisted pair (2-wires)

• Point-to-point distances up to 5 miles (all data rates) on 24 AWG

twisted pair

• Remote digital loopback, local line loopback diagnostic modes

• Multi-Rate Symmetric DSL

• V.35 and X.21 Interfaces

• Compatible with Popular Model 1092

• SNMP Manageable with 1092ARC and 1001MC as 1001MC SNMP

Agent Rack Card

• Universal Power Options, 120VAC, 230VAC and -48VDC Available

• Front Panel Status Indicators

• Small, Convienent Desktop Unit

• CE Marked

2.2 DESCRIPTION

The

Patton Model 1082

is a high speed, AC powered short range

modem that is able to operate synchronously or asynchronously—full

duplex—over a single twisted pair. Supporting data rates to 128 kbps—

or 144 kbps on 1082/144 models—(synchronous) or 38.4 kbps (asyn-

chronous), the Model 1082 is capable of point-to-point distances up to 5

miles using 24 AWG wire.

The Model 1082 supports internal, external or receive loopback clocking

in synchronous mode.Data rates and asynchronous data format may be

conﬁgured locally using DIP switches.

* 144 kbps available on 1082/144 models only.

Model 1082/C provides a V.35 interface on an M/34 female connector.

Model 1082/D provides an X.21 interface on a DB-15 female connector.

Line connection is made by an RJ-45 jack. Standard versions of Model

1082 are powered by a 100-240VAC (Universal) supply.The DC power

supply option supports any DC input between 36–72VDC.

2.3 1082 SNMP MANAGEMENT SOLUTIONS

The Model 1082 and Model 1082/144 are SNMP manageable when con-

nected to a rack-mounted Model 1092ARC (see Figure 1).SNMP manage-

ment is enabled through a 1001MC rack management card located in the

Patton Electronics Rack System.

Figure 1.

Typical application

HTTP/HTML Management

The 1001MC maintains HTML pages that can be viewed through a Web

browser.You can display remote statistics and conﬁgure Model 1082

parameters simply by entering the 1001MC’s IP address into the browser.

10Base-T

connection

to 1001MC

Management

Station

Rack-mounted

1092ARCs

2B1Q

connections to

remote 1082s

Model 1082

3.0 CONFIGURATION

The Model 1082 and 1082/144 each are equipped with 16 DIP switches

that enable conﬁguration of the unit for a wide variety of applications.

This section describes switch locations and explains the different conﬁg-

urations

3.1 CONFIGURING THE HARDWARE DIP SWITCHES

Using a small ﬂat-tip screwdriver, remove the protective cover located on

the underside of the Model 1092 (see Figure 2).

Figure 2.

Removing the cover to access DIP switches S1 and S2

511

G.703/G.704 Test Modes

511E

Model 1194E Single Mode Fiber - Quad G.703/G.704 Modem

511/RDL

TMER

NSStatus

NetLink 10BastT iDSL Modem

10BTDSL

Normal

511E/RBL

Link

Figure 3.

DIP switches S2 and S2

Figure 3 shows the orientation of the DIP switches in the “ON”and “OFF”

positions.

Conﬁguring DIP Switch S1

DIP switch S1 is where you conﬁgure the data rate, asynchronous or

synchronous data format, transmit clock source, and response to RDL

request.The following table summarizes default positions of DIP

switches S1-1 through S1-8. Detailed descriptions of each switch follow

the table.

1234

5678

1234

5678

1234

5678

Push toggle up

for ON position

Switch toggle

Push toggle

down for

OFF position

1234

5678

S1 S2

Position Function Factory Default

S1-1 Data Rate On

S1-2 Data Rate Off

On DSR On

S1-4 Reserved On

S1-5 Async/Sync Data Format Off

S1-6 Tx Clock Source On

S1-7 Tx Clock Source On

S1-8 Response to RDL Request On Enable

64K Sync

}

Internal Clock

S1 SummaryTable

DSR during Local Line LoopS1-3

Note

When setting the 1082 for SNMP Management, the DTE rate

switches (S1-1,S1-2, and S2-1) must be also set to the ON posi-

tion.Therefore, to set a 1082 unit SNMP Mangagement mode, the

following switches have to be at the ON position, S1-1, S1-2, S2-1.

Switches S1-1 and S1-2: Data Rate

Use switches S1-1 and S1-2 to conﬁgure the asynchronous or synchro-

nous data rate of the Model 1082 and Model 1082/144.Each setting rep-

resents one synchronous data rate and one asynchronous data rate.

Note

The Model 1082 can also operate at the 19.2 kbps synchronous

rate, and the Model 1092/144 can also operate at the 144 kbps

synchronous rate.To operate at these rates, set switches S1-1

and S1-2 both to the OFF position and Switch S2-1 to the ON

position (see section , “Conﬁguring DIP switch S2” on page 122

for a description of Switch S2-1).

If the S2-1 switch is positioned in the OFF position, the 128 kbps

sync data rate/0–38.4 kbps async data rate option is selected.

Switch S1-3: Data Set Ready during Line LoopbackTest

Use Switch S1-3 to control the behavior of the DSR signal at the EIA

interface during the line loopback test.

S1-1 S1-2 Sync Data Rate Async. Data Rate

On On 32 kbps Reserved

Off On 56 kbps Reserved

On Off 64 kbps Reserved

Off Off 128 kbps (see note) 0–38.4 kbps

Off Off 144 kbps or 19.2 kbps (see note) Reserved

S1-3 Setting

On DSR is on during local line loop

Off DSR is off during local line loop

Autres manuels pour NetLink 1082

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Patton electronics Modem

Patton electronics

Patton electronics 1004ABRC Manuel utilisateur

Patton electronics

Patton electronics OnSite 1069 Manuel utilisateur

Patton electronics

Patton electronics 1010B Manuel utilisateur

Patton electronics

Patton electronics 1194 Manuel utilisateur

Patton electronics

Patton electronics 1088/K Manuel utilisateur

Patton electronics

Patton electronics 1089/I Manuel utilisateur

Patton electronics

Patton electronics 1058 Manuel utilisateur

Patton electronics

Patton electronics DIAMONDLINK 3201 Manuel utilisateur

Patton electronics

Patton electronics 1092 Manuel utilisateur

Patton electronics

Patton electronics 1007 Manuel utilisateur

Patton electronics

Patton electronics 1180 Manuel utilisateur

Patton electronics

Patton electronics 1082/F Manuel utilisateur

Patton electronics

Patton electronics 1140ARC Manuel utilisateur

Patton electronics

Patton electronics NetLink 1082/144 Manuel utilisateur

Patton electronics

Patton electronics 2192 Manuel utilisateur

Patton electronics

Patton electronics 3012/V24, 3014/V24, 3018/V24 Manuel utilisateur

Patton electronics

Patton electronics 1186 Manuel utilisateur

Patton electronics

Patton electronics NetLink 1082/I Manuel utilisateur

Patton electronics

Patton electronics MODEL 1012AR Manuel utilisateur

Patton electronics

Patton electronics MODEL 1075 Manuel utilisateur

Patton electronics

Patton electronics 1004 Manuel utilisateur

Patton electronics

Patton electronics 1089/C Manuel utilisateur

Patton electronics

Patton electronics 1110ARC Manuel utilisateur

Patton electronics

Patton electronics 1140 Manuel utilisateur

Manuels Modem populaires d'autres marques

Davicom

Davicom DM562AP Manuel utilisateur

EpiValley

EpiValley TATA indicom SXC-1080 Manuel utilisateur

Zte

Zte WiMAX Manuel utilisateur

Intelimax

Intelimax MA-2060 Manuel utilisateur

SMC Networks

SMC Networks D3CM1604V Manuel d'utilisation et d'entretien

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manuel utilisateur

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manuel utilisateur

Samsung

Samsung AceLink SAM-335A Manuel utilisateur

Enfora

Enfora Enabler-G Guide de configuration rapide

iRZ

iRZ ATM2-232 Manuel utilisateur

Zhone

Zhone 6310 Manuel utilisateur

Paradyne

Paradyne Hotwire 7976 Manuel utilisateur

US Robotics

US Robotics 3453C Manuel utilisateur

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manuel utilisateur

Zte

Zte MF823 Manuel utilisateur

Four-Faith

Four-Faith F1403 Manuel utilisateur

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manuel utilisateur

Gemtek

Gemtek WiMAX WIXFBR-103 Manuel utilisateur