Patton electronics NetLink 1095 Manuel utilisateur

USER

MANUAL

MODEL 1095

NetLink™ mDSL

Multi-Rate

Symmetric DSL Modem

Part# 07M1095-F

Doc# 033051UF

Revised 06/08/00

SALES OFFICE

(301)975-1000

TECHNICAL SUPPORT

(301)975-1007

http://www.patton.com

CERTIFIED

An ISO-9001

Certified

Company

TABLE OF CONTENTS

Section Page

1.0 Warranty Information.............................................................2

1.1 Radio and TV Interference

1.2. CE Notice

1.3 Service

2.0 General Information...............................................................4

2.1 Features

2.2 Description

3.0 Configuration..........................................................................5

3.1 Configuring the Hardware DIP Switches

3.1.1 Configuration DIP Switch Set “S1”

3.1.2 Configuration DIP Switch Set “S2”

3.1.3 Configuration DIP Switch Set “S3”

3.2 Configuring the Software Switches

3.3 VT100 Terminal Configuration

3.4 NetLink Plug-and-Play

4.0 Installation ...........................................................................16

4.1 Connecting the Twisted Pair Interface

4.2 Connecting the Serial Port

4.2.1 Changing

QuikConnect™

Modules

4.2.2 Connecting a “DTE” Device

4.2.3 Connecting a “DCE” Device

4.2.4 Configuring the X.21

QuikConnect™

Module

4.3 Connecting Power

4.3.1 Connecting to an AC Power Source

4.3.2 Connecting to a DC Power Source

5.0 Operation.............................................................................21

5.1 Power-Up

5.2 LED Status Monitors

5.3 Test Modes

5.3.1 Overview

5.3.2 Loops and Patterns

5.3.3 Using the V.52 (BER) Test Pattern Generator

Appendix A - Specifications........................................................32

Appendix B - Factory Replacement Parts and Accessories.......33

Appendix C - Interface Pin Assignments....................................34

Appendix D - Transmission Distance Chart................................36

Appendix E - LED Descriptions...................................................37

Appendix F - EIA-561 Control Port Pin Out.................................38

1.0 WARRANTY INFORMATION

Patton Electronics warrants all Model 1095 components to be

free from defects, and will—at our option—repair or replace the prod-

uct should it fail within one year from the first date of shipment.

This warranty is limited to defects in workmanship or materials,

and does not cover customer damage, abuse or unauthorized modifi-

cation. If this product fails or does not perform as warranted, your sole

recourse shall be repair or replacement as described above. Under no

condition shall Patton Electronics be liable for any damages incurred

by the use of this product. These damages include, but are not limited

to, the following: lost profits, lost savings and incidental or consequen-

tial damages arising from the use of or inability to use this product.

Patton Electronics specifically disclaims all other warranties,

expressed or implied, and the installation or use of this product shall

be deemed an acceptance of these terms by the user.

1.1 RADIO AND TV INTERFERENCE

The Model 1095 generates and uses radio frequency energy, and

if not installed and used properly—that is, in strict accordance with the

manufacturer's instructions—may cause interference to radio and tele-

vision reception. The Model 1095 has been tested and found to com-

ply with the limits for a Class A computing device in accordance with

the specifications in Subpart J of Part 15 of FCC rules, which are

designed to provide reasonable protection from such interference in a

commercial installation. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If the Model 1095 does

cause interference to radio or television reception, which can be deter-

mined by disconnecting the unit, the user is encouraged to try to cor-

rect the interference by one or more of the following measures: mov-

ing the computing equipment away from the receiver, re-orienting the

receiving antenna and/or plugging the receiving equipment into a dif-

ferent AC outlet (such that the computing equipment and receiver are

on different branches).

1.2 CE NOTICE

The CE symbol on your Patton Electronics equipment indicates

that it is in compliance with the Electromagnetic Compatibility (EMC)

directive and the Low Voltage Directive (LVD) of the European Union

(EU). A Certificate of Compliance is available by contacting Technical

Support.

1.3 SERVICE

All warranty and non-warranty repairs must be returned freight

prepaid and insured to Patton Electronics. All returns must have a

Return Materials Authorization number on the outside of the shipping

container. This number may be obtained from Patton Electronics

Technical Service at:

tel: 301-975-1007

email: [email protected]

www: http://www.patton.com

Patton Electronics' technical staff is also available to answer any

questions that might arise concerning the installation or use of your

Model 1095. Technical Service hours: 8AM to 5PM EST, Monday

through Friday.

2.0 GENERAL INFORMATION

Thank you for purchasing this Patton Electronics product. If ques-

tions or problems arise during installation or use of this product, please

do not contact Patton Electronics Technical Support at (301) 975-1007.

2.1 FEATURES

• DSL Distances on just two wires using mDSL technology

• DTE Speeds from 64 kbps to 2.3 Mbps

• NetLink Plug-and-Play Master or Slave

• Standalone (QuikConnect™) and Rackmount Versions Available

• SNMP Network Management with In-Band Management of Remote

Units plus Advanced Diagnostics & Statistics using Patton Model

1000MC

• Internal, external or receive recovered clocking options

• LED indicators for TD, RD, CTS, CD, DTR, TM, ER and NS

2.2 DESCRIPTION

The Patton Electronics

NetLink

Model 1095 mDSL

Multi-Rate

DSL Modem provides high speed 2-wire connectivity to ISPs, PTTs,

and corporations using mDSL (Multi-rate Digital Subscriber Line) tech-

nology. Multi-rate DSL offers the ability to deliver the maximum bit rate

that a twisted pair line can accommodate. Supporting multiple line rates

from 144kbps to 2.320Mbps, the NetLink provides “megabyte” speeds

to leased line, LAN to LAN interconnection, and WAN access networks

over 3.6 miles/5.8km (1.054Mbps on 24AWG/.5mm wire).The Model

1095 mDSL standalone allows DTE speeds from 64 kbps to 2.3 Mbps

in increments of 64kbps. Features include loopback diagnostics, in-band

SNMP/HTTP remote management capabilities using NetLink Plug-and-

Play, and externally accessible configuration switches.

A high density 2U-high rack card version of the Model 1095 mDSL

is also available. As a symmetric DSL NTU, the Model 1095 offers the

same data rates in both directions over a single pair of voice-grade

telephone lines using Carrierless Amplitude and Phase (CAP) modula-

tion. Featuring replaceable DCE-DTE interface modules, the NetLink

mDSL can be configured for a huge range of V.24/RS-232, V.35, RS-

422/530, G.703 and X.21 applications.The standard Model 1095 is

option supports any DC input between 36–72 VDC. Using the NetLink

Plug-and-Play feature, the standalone unit at the Customer Premise

site will automatically configure itself to the DTE rate of the rack card

at the Central Office. Other configuration parameters fall to the default

state.This allows changes in the configuration to be handled from a

single end of the link.

IMPORTANT: The Model 1095 is equipped with flash

upgrade. Please refer to Patton website, or contactTechnical

Support for the latest version of the software.

NOTE: Packages received without an RMA number will not be

accepted.

3.0 CONFIGURATION

The Model 1095 is equipped with three sets of eight DIP switches,

which allow configuration of the unit for a wide variety of applications.

This section describes switch locations and explains all possible config-

urations.

3.1 CONFIGURING THE HARDWARE DIP SWITCHES

The 24 external switches are grouped into three eight-switch sets,

and are externally accessible from the underside of the Model 1095

(See Figure 1).

3.1.1 Configuration DIP Switch Set “S1”

All switches in Switch Set S1 are reserved for future use.

These switches must remain in the ON position (See Figure 2).

Figure 2. Close Up of Configuration Switches (all sets are identical in appearance)

Figure 1. Underside of Model 1095, Showing Location of DIP Switches

Front

Back On S3

Off

3.1.2 Configuration DIP Switch Set “S2”

The configuration switches on S2 allow you to specify the Clocking

Mode and response to DTE Loop Enable. Default settings of S2 are

shown in the table below.

Switch S2-1, S2-2, S2-3, S2-4, and S-5: Reserved for future use and

should remain in the Off position.

S2 SUMMARY TABLE

Position Function Factory Default

S2-1 Reserved Off

S2-2 Reserved Off

S2-3 Reserved Off

S2-4 Reserved Off

S2-5 Reserved Off

S2-6 Clock Mode On Receive

S2-7 Clock Mode Off Recovered Clock

S2-8 Enable Loop from DTE Off Disable

12345678

OFF

Switches S2-6 and S2-7: Clock Mode

Use Switches S2-6 and S2-7 to configure the 1095 for internal,

external, or receive recover clock mode.

Switch S2-8: Enable/Disable LoopTests from DTE

Use Switch S2-8 to allow Model 1095 to enter loopback tests

when the DTE raises the appropriate loop request pin.

S2-8 Setting

On Response to DTE Loopback Request Enabled

Off Response to DTE Loopback Request Disabled

CO/CP

Unit S2-6 S2-7 Clock Mode Description

CO On On Internal Transmit clock

generated inter-

nally

CO Off On External (DTE) Transmit clock

derived from

terminal inter-

face

CP On Off Receive Recover Transmit clock

derived from the

received line

Off Off

Reserved

3.1.3 Configuration Switch Set “S3”

Use the eight DIP Switches in Switch S3 to enable the DTE con-

nection rate.The following table summarizes default positions of DIP

Switch S3. Detailed descriptions of each switch follow the table.

Switch S3-1: DTE Rate

Use Switch S3-1 through S3-6 to set the DTE bit rate.

S3-1 S3-2 S3-3 S3-4 S3-5 S3-6 DTE Rate (kbps)

Off Off On On On On 64

On On Off On On On 128

Off On Off On On On 192

On Off Off On On On 256

Off Off Off On On On 320

On On On Off On On 384

Off On On Off On On 448

On Off On Off On On 512

Off Off On Off On On 576

On On Off Off On On 640

Off On Off Off On On 704

On Off Off Off On On 768

Off Off Off Off On On 832

On On On On Off On 896

Off On On On Off On 960

On Off On On Off On 1024

Off Off On On Off On 1088

Off On Off On Off On 1216

On Off Off On Off On 1280

Off Off Off On Off On 1344

On On On Off Off On 1408

Off On On Off Off On 1472

S3 SUMMARY TABLE

Position Function Factory Default

S3-1 DTE Rate On

S3-2 DTE Rate Off

S3-3 DTE Rate Off

S3-4 DTE Rate Off

S3-5 DTE Rate On

S3-6 DTE Rate On

S3-7 Reset Software Defaults On Normal Operation

S3-8

Transmit Data Sample Point

On Normal Operation

}

768 kbps

3.2 CONFIGURING THE SOFTWARE SWITCHES

The Model 1095 features a menu-driven command system that

allows you to monitor and configure your Model 1095 stand alone unit.

There are two modes of operation for the Model 1095 control port:

Monitor and Configuration.These are described in more detail below.

Following the Model 1095 setup is a description of how to setup your

VT100, or equivalent, control port for use with the Model 1095.

3.2.1 Monitor

If you are configuring your Model 1095 through the dip-switches

and you wish to check your configuration or view the status of the

modem you can do so by accessing the control port. In this setup the

user is not able to make configuration changes to the unit because the

hardware dip-switch settings are controlling the configuration of the

unit. If you would like to use the control port to configure your unit see

the Configuration section below for setup information.

3.2.2 Configuration

If you plan to use the Model 1095 control port to configure your

unit, you mus set all of the DIP switches to the ON position.This will

force the 1095 into plug-and-play mode (this configuration is also

required if you intend to have the Model 1095 work in a plug-and-play

environment or use the Model 1001MC to configure the unit).

3.2.3 VT100 Terminal Setup

1) Connect the serial RS-232 port of a VT100 or similar DTE with termi-

nal emulation to the EIA/TIA-561 port of the Model 1095. To construct

an RS-232 to EIA-561 patch cable, refer to the control port pinout dia-

gram in Appendix F. Refer to Appendix B to order a pre-made cable.

2) Power up the terminal and set its RS-232 port as follows:

9600 Baud

8 data bits, 1 stop bit, no parity

Local echo

CR-CR/LF on inbound data

ANSI, VT-100 emulation

3) Power up the Model 1095

4) After power up, the control port displays the Main Menu screen. If the

Main Menu is not shown please review your VT100 setup as described

above.

On Off On Off Off On 1536

On On Off Off Off On 1600

Off On Off Off Off On 1664

On Off Off Off Off On 1728

Off Off Off Off Off On 1792

On On On On On Off 1856

Off On On On On Off 1920

On Off On On On Off 1984

Off Off On On On Off 2048

On On Off On On Off 2112

Off On Off On On Off 2176

On Off Off On On Off 2240

Off Off Off On On Off 2304

Switch S3-7: Reset Software Defaults

Switch S3-7 allows the user to reset the software configured facto-

ry defaults. This will only be needed when using the Model 1001MC to

SNMP manage your units. For more information, please refer to the

Model 1001MC Operations Manual.

S3-7 Setting

On Normal Operation

Off Reset

Switch S3-8:Transmit Data (TD) Sampling Point

Switch 3-8 controls the Transmit Data (TD) sampling point.

S3-8 Setting Description

On Normal TD sampled on the falling

edge of the 1095 Transmit

Clock (TC)

Off Invert TD sampled on the rising

edge of the 1095 Transmit

Clock.

NOTE: Based on the DTE rate chosen, the Model 1095 will

automatically select the optimum line rate for the distance. This

selection is based on the lowest line rate that will support the

DTE rate.

3.3 VT100 TERMINAL CONFIGURATION

With software version 2.3.1 or higher, you can configure the 1095 using a

VT100 compatible terminal (or program).With the VT100 Interface, you can

perform all functions available via the DIP switches.The VT100 operation is

available from the main menu page.

3.3.1 Main Menu Screen

The Main Menu screen for the Model 1095 is displayed below.The user

can hit 'Esc' to refresh this screen at any time. If you are running in the

Monitor mode, the Model 1095 will not require a password. If you wish to run

in the Configuration mode, you will be required to enter a password to access

the configuration menus.

The default password shipped with the Model 1095 is all lower case "pat-

ton".The Model 1095 is case sensitive and will not work if the correct pass-

word is not installed. If the incorrect password is entered, you will receive an

error message and be prompted for the password again. It is suggested that

you change your password after setting up your unit to ensure security for your

network.

After entering the correct password the Model 1095 will display the

Software Configuration Menu described below.

3.3.2 Software Configuration Menu

When the correct password is entered, the Software Configuration

Menu will be displayed. Select the option that you would like to change.

NOTE: After making any configuration changes you are required to

select the Exit and Save Changes if you would like the changes to be

implemented into the unit.The Software Configuration Menu is shown

below.

3.3.3 Option #1 DTE Rate

If option 1 is selected in the Software Configuration Menu, a DTE Rate

sub-menu will be displayed to select the DTE Rate of the unit. After

selecting the required DTE rate, the Software Configuration Menu will

be displayed. NOTE: The Model 1095 is currently set for NetLink Plug-

And-Play, all dip-switches in the ON position, if you are connecting your

Model 1095 to a Model 1095RC the stand alone unit will automatically

configure itself for the DTE rate selected on the 1095RC. For more

information on the NetLink Plug-And-Play setup please refer to the

Patton Electronics web site (www.patton.com).

11 12

3.3.4 Option #2 Clock Mode Selection Menu

If option 2 is selected in the Software Configuration Menu, the Model

1095 will display the Clock Mode Selection Menu.This menu will allow

the user to set the clock mode for the Model 1095 stand alone unit.

After making your selection the Model 1095 will display the Software

Configuration Menu.

3.3.5 Option #3 DTE Interface Type

If option 3 is selected in the Software Configuration Menu, the Model

1095 will display the DTE Interface Type Menu.This menu allows the

user to select the type of Quick Connect Module that is installed in the

unit. By default, the Model 1095 is set for Serial/Ethernet Interface.This

selection will cover almost all of the Patton Quick Connect Modules

except the IM1/K G.703/G.704 Quick Connect Module.

If you are using this interface, and it supports n x 64K G.704 network

extension, then you should set your Interface Type for 2) G.703/G.704

Interface.

NOTE: Early versions of the Model IM1/K do not support G.704

network extension. Review your manual to be sure. If your IM1/K is

revision B or earlier, it does not support G.704 extension. Leave your

Model 1095 set for Serial/Ethernet Interface.

3.3.6 Option #4 DTE Loopback Requests

If option 4 is selected the Model 1095 will display the DTE Loopback

Request menu.This menu will allow the user to enable or disable loop-

backs from the DTE interface.The DTE Loopback Request menu is

shown in the following diagram. If the IM1/I Quick Connect Module is

installed, select 2) Disable Response to DTE Loopback Request.

3.3.7 Option #5 Transmit Data Sampling Point

If option 5 is selected the Model 1095 will display the Transmit Data

Sampling Point menu.This menu allows the user to set the sampling

point for the transmit data entering the Model 1095 from the DTE inter-

face. Under normal conditions this variable should be set to normal.

The Transmit Data Sampling Point menu is shown in the following dia-

gram.

3.3.8 Option #6 CO/CP Mode

If option 6 is selected the Model 1095 will display the CO/CP Mode

menu.This option is only needed when the Model 1095 is using the

IM1/K and it is connected to another DSL modem using the

G.703/G.704 interface module (i.e. 1088/K, 1095RC/K, 1095/K, etc). In

that particular application, both the 1095 units should be set for the

external clock mode and one unit will need to be forced into the CP

mode for the DSL line to function properly.

3.3.9 Option #7 Change Password

If option 7 is selected the Model 1095 will request a new password

from the user. After the password is entered the Model 1095 will

request that you confirm the changes.

3.3.10 Exiting the Configuration Mode

After making configuration changes, select option #9 (Exit and Save

Changes) to implement the configuration changes. If you do not want

the configuration changes to be implemented, select option #8 (Exit

Without Saving Changes).

13 14

3.4 NETLINK PLUG-AND-PLAY

The NetLink Plug-and-Play application allows ISPs and PTTs to

quickly upgrade the link speed for a customer without re-configuring

the Customer Premise (CP) Model 1095. It will also allow ISPs and

PTTs to set up all of the configurations at the Central Office (on the

rack cards) before installation of the stand alone units, thus saving time

spent configuring and re-configuring DIP switch settings.

The NetLink Plug-and-Play feature allows the user to configure the

DTE rate for the link from the rack card at the Central Office (CO). The

stand alone unit at the Customer Premise (CP) site will automatically

configure itself to the DTE rate of the rack card. Other configuration

parameters fall to the default state. This allows changes in the configu-

ration to be handled from a single end of the link.

When installing a CO/CP style application, the local end of the link

is comprised of a CO unit (1095RC) set to either Internal or External

clocking mode and a CP unit (1095) set as a NetLink Plug-and-Play

CP.

The NetLink Plug-and-Play CP stand alone will have all of its

DIP switches set to the ON position

(as indicated below in Figure 3).

When the units are connected, the CP will come up with a prede-

fined default configuration (Receive Recovered Clocking). During the

handshaking process between the units, the CO unit will set the DTE

rate/line rate of the CP unit to match its DIP switch configuration set-

tings. If the DTE rate for the link requires a change, the change is

needed only at the CO side of the link.

The NetLink Plug and Play application will also work in the man-

aged system using the Model 1001MC and 1095RC cards installed in

Patton’s 2U rack system. In this application, the system administrator

can configure the entire rack through the Network Management Station

(NMS) before the stand alone (CP) units are installed. For more infor-

mation on the SNMP management of your rack, please refer to the

Model 1001MC Operations Manual.

1095RC

(CO) 1095

(CP)

DIP Switches all in ON position

DIP Switches configured according

to specific application requirements

Figure 3. Typical NetLink Plug-and-Play Application

15 16

4.0 INSTALLATION

Once the Model 1095 is properly configured, it is ready to connect

to the twisted pair interface, to the serial port, and to the power source.

This section tells you how to make these connections.

4.1 CONNECTING THE TWISTED PAIR INTERFACE

The Model 1095 supports communication between two DTE

devices at distances to 5 miles (8 km) over 24 AWG (.5mm) twisted

pair wire. There are two essential requirements for installing the Model

1095:

1. These units work in pairs. Both units at the end of the twisted

pair must have the same 2-Wire connection and DTE rate.

2. To function properly, the Model 1095 needs one

twisted pair of metallic wire. This twisted pair must be

unconditioned, dry, metallic wire, between 19 (.9mm) and 26

AWG (.4mm) (the higher number gauges will limit distance).

Standard dial-up telephone circuits, or leased circuits that run

through signal equalization equipment, or standard, flat modu-

lar telephone type cable, are

not acceptable

The RJ-45 connector on the Model 1095’s twisted pair interface is

polarity insensitive and is wired for a two-wire interface. The signal/pin

relationships are shown in Figure 4 below.

Figure 4. Model 1095 twisted pair line interface.

1 (N/C)

2 (N/C)

3 (N/C)

4 (2-Wire TIP)

5 (2-Wire RING)

6 (N/C)

7 (N/C)

8 (N/C)

4.2 CONNECTING THE SERIAL PORT

The serial port interface on the Model 1095 uses interchangeable

QuikConnect™

Modules. Each

QuikConnect™

Module has a 50-pin

card edge connector on one side and a serial port interface on the

other. Figure 4 below shows how a

QuikConnect™

Module plugs into

the back of the Model 1095.

4.2.1 Changing

QuikConnect™

Modules

When you purchase a particular version of the Model 1095, it

should be shipped to you with the appropriate

QuikConnect™

Module

already installed. If you need to install a different

QuikConnect™

Module, follow these steps:

Removing the Existing

QuikConnect™

Module

1) Turn the power switch off. Leave the power cord plugged into a

grounded outlet to keep the unit grounded.

2) Loosen the two thumbscrews on the module by turning them

counterclockwise.

3) Grasp the two thumbscrews and gently pull the module from

the unit. Apply equal force to the thumbscrews to keep the

module straight during the removal process

Installing the New

QuikConnect™

Module

1) Make sure the power switch is off. Leave the power cord

plugged into a grounded outlet to keep the unit grounded.

0 OFF

1 ON

Line

Interface Port

Figure 5. Installation of Model 1095 Plug-in Serial Interface Module

2) Hold the module with the faceplate toward you and align the

module with the guide slots in the rear panel of the Model

1095.

3) While keeping the module’s faceplate parallel with the Model

1095 rear panel, slide the module straight in – so that the card

edge contacts line up with the socket inside the chassis.

4) With the card edge contacts aligned with the socket, firmly seat

the module by using your thumbs to apply pressure directly to

the right and left edges of the module faceplate. Applying mod-

erate and

even

pressure should be sufficient to seat the mod-

ule. You should hear it “click” into place.

5) To secure the module in place, push the thumbscrews into the

chassis and turn the screws clockwise to tighten.

4.2.2 Connecting to a “DTE” Device

The serial port on most

QuikConnect™

interface modules (all

except the X.21 module) is hard-wired as a DCE. Therefore these

modules “want” to plug into a DTE such as a terminal, PC or host.

When making the connection to your DTE device, use a straight

through cable of the shortest possible length—we recommend 6 feet

or less. When purchasing or constructing an interface cable, please

refer to the pin diagrams in Appendix C as a guide.

4.2.3 Connecting to a “DCE” Device

If the Model 1095’s QuikConnect™ interface module is hard-wired

as a DCE (all except the X.21 module), you must use a

null modem

cable when connecting to a modem, multiplexer or other DCE device.

This cable should be of the shortest possible length—we recommend

6 feet or less. When purchasing or constructing a null modem inter-

face cable, use the pin diagrams in Appendix C as a guide.

NOTE: The card edge connector should meet the socket when

it is almost all the way into the chassis. If you encounter a lot of

resistance, remove the module and repeat steps 2 & 3.

NOTE: Pin-out requirements for null modem applications vary

widely between manufacturers. If you have any questions about

a specific application, contact Patton Electronics Technical

Support.

Table des matières

Autres manuels Patton electronics Modem

Patton electronics

Patton electronics 1082/F Manuel utilisateur

Patton electronics

Patton electronics NetLink 1082/I Manuel utilisateur

Patton electronics

Patton electronics 1092A Manuel utilisateur

Patton electronics

Patton electronics 2703RC Manuel utilisateur

Patton electronics

Patton electronics 1007 Manuel utilisateur

Patton electronics

Patton electronics 1088/C Manuel utilisateur

Patton electronics

Patton electronics RocketLink 3202 Manuel utilisateur

Patton electronics

Patton electronics 1226 Manuel utilisateur

Patton electronics

Patton electronics 1089/C Manuel utilisateur

Patton electronics

Patton electronics 1004ABRC Manuel utilisateur

Patton electronics

Patton electronics 1058 Manuel utilisateur

Patton electronics

Patton electronics 1045 Manuel utilisateur

Patton electronics

Patton electronics 3012/V24, 3014/V24, 3018/V24 Manuel utilisateur

Patton electronics

Patton electronics 1140ARC Manuel utilisateur

Patton electronics

Patton electronics 1068 Manuel utilisateur

Patton electronics

Patton electronics 1089/I Manuel utilisateur

Patton electronics

Patton electronics 1140RC Manuel utilisateur

Patton electronics

Patton electronics 1194 Manuel utilisateur

Patton electronics

Patton electronics OnSite 1052 Series Manuel utilisateur

Patton electronics

Patton electronics IM2RC/F-128K Manuel utilisateur

Patton electronics

Patton electronics 1110 Manuel utilisateur

Patton electronics

Patton electronics 1060 Manuel utilisateur

Patton electronics

Patton electronics 2703-X21 Manuel utilisateur

Patton electronics

Patton electronics 1090 Manuel utilisateur

Manuels Modem populaires d'autres marques

Davicom

Davicom DM562AP Manuel utilisateur

EpiValley

EpiValley TATA indicom SXC-1080 Manuel utilisateur

Zte

Zte WiMAX Manuel utilisateur

Intelimax

Intelimax MA-2060 Manuel utilisateur

SMC Networks

SMC Networks D3CM1604V Manuel d'utilisation et d'entretien

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manuel utilisateur

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manuel utilisateur

Samsung

Samsung AceLink SAM-335A Manuel utilisateur

Enfora

Enfora Enabler-G Guide de configuration rapide

iRZ

iRZ ATM2-232 Manuel utilisateur

Zhone

Zhone 6310 Manuel utilisateur

Paradyne

Paradyne Hotwire 7976 Manuel utilisateur

US Robotics

US Robotics 3453C Manuel utilisateur

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manuel utilisateur

Zte

Zte MF823 Manuel utilisateur

Four-Faith

Four-Faith F1403 Manuel utilisateur

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manuel utilisateur

Gemtek

Gemtek WiMAX WIXFBR-103 Manuel utilisateur