Patton electronics 1009 Manuel utilisateur

USER MANUAL

MODEL 1009/1009S

Ultra-miniature, Asynchronous,

DB-9 Short Range Modem

1.0 WARRANTY INFORMATION

Patton Electronics warrants all Model 1009 components to be

free from defects, and will—at our option—repair or replace the product

should it fail within one year from the first date of shipment.

This warranty is limited to defects in workmanship or materials, and

does not cover customer damage, abuse, or unauthorized modification.

If this product fails or does not perform as warranted, your sole

recourse shall be repair or replacement as described above. Under no

condition shall Patton Electronics be liable for any damages incurred

by the use of this product. These damages include, but are not limited

to, the following: lost profits, lost savings, and incidental or

consequential damages arising from the use of or inability to use this

product. Patton Electronics specifically disclaims all other warranties,

expressed or implied, and the installation or use of this product shall be

deemed an acceptance of these terms by the user.

1.1 RADIO AND TV INTERFERENCE

The Model 1009 generates and uses radio frequency energy, and if

not installed and used properly—that is, in strict accordance with the

manufacturer's instructions—may cause interference to radio and

television reception. The Model 1009 has been tested and found to

comply with the limits for a Class A computing device in accordance

with the specifications in Subpart J of Part 15 of FCC rules, which are

designed to provide reasonable protection from such interference in a

commercial installation. However, there is no guarantee that

interference will not occur in a particular installation. If the Model 1009

does cause interference to radio or television reception, which can be

determined by disconnecting the RS-232 interface, the user is

encouraged to try to correct the interference by one or more of the

following measures: moving the computing equipment away from the

receiver, re-orienting the receiving antenna, and/or plugging the

receiving equipment into a different AC outlet (such that the computing

equipment and receiver are on different branches).

1.2 CE NOTICE

The CE symbol on your Patton Electronics equipment indicates

that it is in compliance with the Electromagnetic Compatibility (EMC)

directive and the Low Voltage Directive (LVD) of the Union European

(EU). A Certificate of Compliance is available by contacting Patton

Technical Support.

1.3 SERVICE

All warranty and non-warranty repairs must be returned freight

prepaid and insured to Patton Electronics. All returns must have a

Return Materials Authorization number on the outside of the shipping

container. This number may be obtained from Patton Electronics

Technical Service at (301) 975-1007; http://www.patton.com: or,

[email protected].

NOTE: Packages received without an RMA number will not be

accepted.

Patton Electronics' technical staff is also available to answer any

questions that might arise concerning the installation or use of your

Model 1009. Technical Service hours: 8AM to 5PM EST, Monday

through Friday.

2.0 GENERAL INFORMATION

Thank you for your purchase of this Patton Electronics product.

This product has been thoroughly inspected and tested and is

warranted for One Year parts and labor. If any questions or problems

arise during installation or use of this product, please do not hesitate to

contact Patton Electronics Technical Support at (301) 975-1007.

2.1 FEATURES

• Full duplex, asynchronous operation over 4 wires

• Data rates from 300 to 19,200 bps

• Ranges to 17 miles (27.2 km) using 19 AWG (0.9mm) wire

• No AC power required; draws necessary power from

RS-232 signals

• Ultra-miniature size (2.50" x 1.20" x 0.75") (6.4 x 3.0 x 1.9 cm)

• Twisted pair connection via strain relief, RJ-11 or RJ-45

• Compatible with Model 1000 and 1015 Short Hauls

• Made in the USA

2.2 DESCRIPTION

The Model 1009 Asynchronous Short Range Modem lets two

asynchronous RS-232 devices with DB-9 connectors communicate at

distances up to 17 miles. Operating full duplex over two unconditioned

twisted pair, the Model 1009 supports data rates from 300 to 19,200

bps. The Model 1009 draws all necessary operating power from the

RS-232 interface, and requires no AC power or batteries.

The Model 1009 has been designed to connect directly to IBM AT

compatibles, Unisys 6000/7000 Series, NCR "Towers" and other RS-

232 machines with DB-9 serial ports. Its ultra-miniature size (2.50" x

1.20" x 0.75") allows the Model 1009 to fit in very tight installation

spaces. Twisted pair connection can be made using RJ-11, RJ-45 or

terminal blocks with strain relief. For added flexibility, the Model 1009 is

compatible with Patton's Model 1000 and 1015 Short Hauls.

The Model 1009S uses the latest in bi-directional, clamping

transient suppressors to guard itself and connected equipment against

data line transients. For surge handling capability, the Model 1009S is

compliant with IEC 801.5, Level 2, 1kV. The Model 1009S is

recommended for environments prone to lightning storms, static

discharge and other forms of EMR.

3.0 INSTALLATION

The Model 1009 is easy to install and requires no pre-

configuration. This section tells you how to properly connect the Model

1009 to the twisted pair and RS-232 interfaces, and how to operate the

Model 1009.

3.1 CONNECTION TO THE TWISTED PAIR INTERFACE

The Model 1009 operates full duplex in point-to-point

environments. It passes data as well as X-ON/X-OFF (software)

handshaking signals. There are two essential requirements for

installing the Model 1009:

1. These units work in

pairs

. Therefore, you must have one Model

1009 at each end of a two twisted pair interface.

2. To function properly, the Model 1009 needs two twisted pairs of

metallic wire. These pairs must be

unconditioned

, dry, metallic wire,

between 19 and 26 AWG (the higher number gauges may limit distance

somewhat). Standard dial-up telephone circuits, or leased circuits that

run through signal equalization equipment, are

not acceptable

For your convenience, the Model 1009 is available with three

different twisted pair interfaces: RJ-11 jack, RJ-45 jack, and terminal

blocks with strain relief.

3.1.1 TWISTED PAIR CONNECTION USING RJ-11 OR RJ-45

The RJ-11 and RJ-45 connectors on the Model 1009's twisted pair

interface are pre-wired for a standard TELCO wiring environment. The

signal/pin relationships are shown below:

RJ-11 SIGNAL RJ-45 SIGNAL

1----------------GND* 1 --------------N/C

2----------------RCV- 2 --------------GND*

3----------------XMT+ 3 --------------RCV-

4----------------XMT- 4 --------------XMT+

5----------------RCV+ 5 --------------XMT-

6----------------GND* 6 --------------RCV+

7 --------------GND*

8 --------------N/C

* Connection to Ground is Optional

When connecting two Model 1009s it is necessary to use a "cross

over" cable. The diagram below shows how a cross over cable should

be constructed for an environment where both Model 1009s use a 6-

wire RJ-11 connector. Similar logic should be followed when using RJ-

45 connectors or a combination of the two.

SIGNAL PIN# COLOR COLOR PIN# SIGNAL

GND* 1 Blue** ------------White 6 GND

RCV- 2 Yellow------------Red 4 XMT-

XMT+ 3 Green ------------Black 5 RCV+

XMT- 4 Red---------------Yellow 2 RCV-

RCV+ 5 Black -------------Green 3 XMT+

GND 6 White-------------Blue 1 GND

*Connection to Ground is Optional

**Standard Color Codes - Yours may be different

3.1.2 TERMINAL BLOCK TWISTED PAIR CONNECTION

If your application requires you to connect one or two pairs of bare

wires to the Model 1009, you will need to access the internal terminal

blocks. The instructions on the following pages will tell you how to

open the case, connect the bare wires to the terminal blocks, and

fasten the strain relief collar in place so that the wires won't pull loose.

Note: The terminal block configurations are different for the 1009M

(male) and 1009F (female).

1. Open the unit by gently inserting a screw driver between the DB-

9 connector and the lip of the plastic case (See below). You don't have

to worry about breaking the plastic, but be careful not to bend the D-sub

connector.

Once the unit has been opened, you will be able to see the

terminal block located at the rear of the PC board.

2. Strip the outer insulation from the twisted pairs about one inch

from the end.

+- -+

XMT G RCV

+- -+

XMTGRCV

1009M 1009F

Figure 1: RJ-11 and RJ-45 Modular Pin Assignments

RJ-11 Jack RJ-45 Jack

Figure 2: 1009M and 1009F Terminal Block Signal Orientation

Figure 3: How to Use a Small Flathead Screwdriver to Begin to Open the Model 2070 Case

Figure 4: How to Use a Small Flathead Screwdriver to Finish Opening the Model 2070 Case

Figure 5: Stripping the Outer Insulation from the Twisted Pair

3. Strip back the insulation on each of the 2 twisted pair wires

about .25".

4. Connect

one pair

of wires to XMT+ and XMT- (transmit positive

and negative) on the terminal block, making careful note of which color

is positive, and which color is negative.

5. Connect the

other pair

of wires to RCV+ and RCV- (receive

positive and negative) on the terminal block, again making careful note

of which color is positive, and which color is negative.

Ultimately, you will want to construct a two pair cross over cable that

makes a connection between the Model 1009s as shown below:

6. If there is a shield around the telephone cable, it may be

connected to "G" on the terminal block. We recommend connecting the

shield at the computer end only to avoid ground loops. A ground wire is

not necessary

for proper operation of the Model 1009.

7. When you finish connecting the wires to the terminal block, the

assembly should resemble the diagram below:

8. Place the 2 halves of the strain relief assembly on either side of

the telephone wire and press together very lightly. Slide the assembly

so that it is about 2 inches from the terminal posts and press together

firmly. If your cable diameter is too small or too large for our strain

relief, please contact our technical support. We have strain relief

assemblies to accommodate most cable diameters.

9. Insert the strain relief assembly with the wire going through it

into the slot in the bottom half of the modem case and seat it into the

recess in the case. (If the telephone wire is too thin to be held by the

strain relief assembly, you will need to order a different sized strain

relief. Call Patton's Sales Department at (301) 975-1000.)

+RCV- G -XMT+ +RCV- G -XMT+

7 8

XMT + RCV+

XMT - RCV -

RCV - XMT -

RCV + XMT +

To Shield (Optional) }One Pair

}One Pair

Figure 6: Stripping the Inner Insulation from Each Twisted Pair

Figure 7: Proper Twisted Pair Connections to the Model 1009 Terminal Blocks

Figure 8: Re-connecting the Strain Relief Assembly

Figure 9: Positioning the Model 1000 Inside the Plastic Case

10. BEND the top half of the case as necessary to place it over the

strain relief assembly. Do not snap the case together yet.

11. Insert one captive screw through a saddle washer and then

insert the captive screw with the washer on it, through the hole in the

DB-25 end of the case. Snap that side of the case closed. Repeat the

process for the other side. This completes the cable installation

process.

3.2 CONNECTION TO THE RS-232 INTERFACE

The Model 1009 is configured as a DCE, and is designed to

connect to the DB-9 serial port of an RS-232 DTE (PC, laptop, host).

If you must use a cable to connect the Model 1009 to the DTE device,

make sure that it is a

straight through

cable of the shortest possible

length—we recommend 6 ft or less (See Appendix C).

Should you wish to connect a DTE to a DCE using short range

modems (ex. a PC/AT connecting to a multiplexer several hundred feet

away), we recommend using a Model 1009 for the DB-9 DTE

connection and a Patton Model 1000 for the DB-25 DCE connection.

These two short hauls

are compatible

. If you need to use a Model 1009

on both ends, connection to the DCE device will require a

cross over

RS-232 cable. Call Patton Technical Support at (301) 975-1007 for

more details.

3.3 OPERATING THE MODEL 1009

Once the Model 1009 is properly installed, it should operate

transparently—as if it were a standard cable connection. Operating

power is derived from the RS-232 data and control signals; there is no

"ON/OFF" switch. All data from the RS-232 interface, including

X-ON/X-OFF flow control information, is passed straight through. Any

hardware flow control signals are looped back at the interface and are

not passed between the short hauls.

APPENDIX A

PATTON MODEL 1009/1009S SPECIFICATIONS

Transmission Format: Asynchronous

Data Rate: 0 to 19,200 bps (no strapping)

Control Signal: CTS (Pin 8) turns ON immediately after the

terminal raises RTS (Pin 7). DSR (Pin 6)

and DCD (Pin 1) turn ON immediately after

the terminal raises DTR (Pin 4).

Transmit Line: 4 wire, unconditioned line (2 twisted pairs)

Transmit Mode: Full Duplex, 4-wire

Transmit Level: 0 dBm

Line Connection: RJ-11 or RJ-45 jack or 5 screw terminal

posts (4 wires and 1 ground) and a strain

relief insert. Works well with data signals

only.

Surge Protection: Compliant with IEC 801.5 level 2,

1kV (Model 1009S Only)

Power Supply: None required, uses ultra low power from

EIA data and control signals

Size: 2.50" x 1.2" x .75" (6.4 x 3.0 x 1.9 cm)

9 10

24 AWG

(0.5 mm) 26 AWG

(0.4 mm)

19 AWG

( 0.9 mm)

19,200 6.2(9.9) 3.7(5.9) 1.2(1.9)

9,600 7.5(12.0) 4.9(7.8) 2.5(4.0)

4,800 8.7(13.9) 5.6(9.0) 3.7(5.9)

2,400 11.8(18.9) 8.0(12.8) 4.9(7.8)

1,200 17.0(27.2) 11.8(18.9) 8.0(12.8)

Data Rate

(bps)

Model 1009 Distance Table in Miles (km)

Wire Gauge

Figure 10. Connecting the Case Halves

APPENDIX B

PATTON MODEL 1009 CABLE RECOMMENDATIONS

The Patton Model 1009 operates at frequencies of 20kHz or less

and has been performance tested by Patton technicians using twisted-

pair cable with the following characteristics:

Wire Gauge Capacitance Resistance

19 AWG/.9mm 83nf/mi or 15.72 pf/ft. .0163 Ohms/ft.

22 AWG/.6mm 83nf/mi or 15.72 pf/ft. .0326 Ohms/ft.

24 AWG/.5mm 83nf/mi or 15.72 pf/ft. .05165 Ohms/ft.

To gain optimum performance from the Model 1009 please keep the

following guidelines in mind:

•

Always

use twisted pair wire—this is not an option.

• Use twisted pair wire with a capacitance of 20pf/ft or less.

• Avoid twisted pair wire thinner than 26 AWG (i.e. avoid higher

AWG numbers than 26)

• Use of twisted pair with a resistance greater than the above

specifications may cause a reduction in maximum distance

obtainable. Functionality should not be affected.

• Environmental factors too numerous to mention can affect the

maximum distances obtainable at a particular site. Use “maximum

distance” figures as a general guideline only

APPENDIX C

PATTON MODEL 1009 PIN ASSIGNMENTS

(D-Sub 9 Connector, DCE Configuration)

1- (FG)Data Carrier Detect From Model 1009

2- (RD) Receive Data From Model 1009

3- (TD) Transmit Data To Model 1009

4- (DTR)Data Terminal Ready To Model 1009

5- (SG) Signal Ground -

From Model 1009 Data Set Ready (DSR) - 6

To Model 1009 Request To Send (RTS) - 7

From Model 1009 Clear to Send (CTS) - 8

DIRECTION STANDARD "DCE" CONFIGURATION DIRECTION

11 12

APPENDIX D

PATTON MODEL 1009/1009S BLOCK DIAGRAM Dear Valued Customer,

Thank you for purchasing Patton Electronics products! We do

appreciate your business. I trust that you find this user manual helpful.

We manufacture one of the widest selections of data

communications products in the world including CSU/DSU's, network

termination units, powered and self-powered short range modems, fiber optic

modems, interface converters, baluns, electronic data switches, data-line surge

protectors, multiplexers, transceivers, hubs, print servers and much more. We

produce these products at our Gaithersburg, MD, USA, facility, and can

custom manufacture products for your unique needs.

We would like to hear from you. Please contact us in any of the

following ways to tell us how you like this product and how we can meet your

product needs today and in the future.

Web: http://www.patton.com

Sales E-mail: [email protected]

Support E-mail: [email protected]

Phone - Sales (301) 975-1000

Phone - Support (301) 975-1007

Fax: (301) 869-9293

Mail: Patton Electronics Company

7622 Rickenbacker Drive

Gaithersburg, MD 20879 USA

We are committed to a quality product at a quality price. Patton

Electronics is BABT and ISO 9001 certified. We meet and exceed the highest

standards in the industry (CE, UL, etc.).

It is our business to serve you. If you are not satisfied with any

aspect of this product or the service provided from Patton Electronics or its

distributors, please let us know.

Thank you.

Burton A.Patton

Vice President

P.S. Please tell us where you purchased this product:

________________________________________________________

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Patton electronics Modem

Patton electronics

Patton electronics 1006 Manuel utilisateur

Patton electronics

Patton electronics MODEL 1075 Manuel utilisateur

Patton electronics

Patton electronics 12168 Manuel utilisateur

Patton electronics

Patton electronics 3012/V24, 3014/V24, 3018/V24 Manuel utilisateur

Patton electronics

Patton electronics 1140 Manuel utilisateur

Patton electronics

Patton electronics 1205 Manuel utilisateur

Patton electronics

Patton electronics OnSite 1069 Manuel utilisateur

Patton electronics

Patton electronics ParaLink 1225 Manuel utilisateur

Patton electronics

Patton electronics 1070RC Manuel utilisateur

Patton electronics

Patton electronics 1093 Manuel utilisateur

Patton electronics

Patton electronics 1012B Manuel utilisateur

Patton electronics

Patton electronics RocketLink-G 3088 Series Manuel utilisateur

Patton electronics

Patton electronics 1140A Manuel utilisateur

Patton electronics

Patton electronics 1088/C Manuel utilisateur

Patton electronics

Patton electronics 1089/C Manuel utilisateur

Patton electronics

Patton electronics 1092A Manuel utilisateur

Patton electronics

Patton electronics 1088/K Manuel utilisateur

Patton electronics

Patton electronics NetLink 1082 Manuel utilisateur

Patton electronics

Patton electronics 1015 Manuel utilisateur

Patton electronics

Patton electronics MODEL 1012AR Manuel utilisateur

Patton electronics

Patton electronics IM2RC/F-128K Manuel utilisateur

Patton electronics

Patton electronics 1203 Manuel utilisateur

Patton electronics

Patton electronics 1089/I Manuel utilisateur

Patton electronics

Patton electronics 1110ARC Manuel utilisateur

Manuels Modem populaires d'autres marques

Davicom

Davicom DM562AP Manuel utilisateur

EpiValley

EpiValley TATA indicom SXC-1080 Manuel utilisateur

Zte

Zte WiMAX Manuel utilisateur

Intelimax

Intelimax MA-2060 Manuel utilisateur

SMC Networks

SMC Networks D3CM1604V Manuel d'utilisation et d'entretien

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manuel utilisateur

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manuel utilisateur

Samsung

Samsung AceLink SAM-335A Manuel utilisateur

Enfora

Enfora Enabler-G Guide de configuration rapide

iRZ

iRZ ATM2-232 Manuel utilisateur

Zhone

Zhone 6310 Manuel utilisateur

Paradyne

Paradyne Hotwire 7976 Manuel utilisateur

US Robotics

US Robotics 3453C Manuel utilisateur

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manuel utilisateur

Zte

Zte MF823 Manuel utilisateur

Four-Faith

Four-Faith F1403 Manuel utilisateur

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manuel utilisateur

Gemtek

Gemtek WiMAX WIXFBR-103 Manuel utilisateur