Paradyne COMSPHERE 3610 Manuel utilisateur
COMSPHERE
3600 SERIES
DATA SERVICE UNITS
TIME DIVISION MULTIPLEXER,
MULTICHANNEL MULTIPOINT,
AND DIGITAL BRIDGE OPTIONS
QUICK REFERENCE
Document No. 3610-A2-GL12-00
Copyright 1998 Paradyne Corporation.
All rights reserved.
Printed in U.S.A.
Notice
This publication is protected by federal copyright law. No part of this publication may be
copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated
into any human or computer language in any form or by any means, electronic,
mechanical, magnetic, manual or otherwise, or disclosed to third parties without the
express written permission of Paradyne Corporation, 8545 126th Ave. N., Largo,
FL 33773.
Paradyne Corporation makes no representation or warranties with respect to the
contents hereof and specifically disclaims any implied warranties of merchantability or
fitness for a particular purpose. Further, Paradyne Corporation reserves the right to
revise this publication and to make changes from time to time in the contents hereof
without obligation of Paradyne Corporation to notify any person of such revision or
changes.
Changes and enhancements to the product and to the information herein will be
documented and issued as a new release to this manual.
Warranty, Sales, and Service Information
Contact your local sales representative, service representative, or distributor directly for
any help needed. For additional information concerning warranty, sales, service, repair,
installation, documentation, training, distributor locations, or Paradyne worldwide office
locations, use one of the following methods:
Via the Internet: Visit the Paradyne World Wide Web site at
http://www.paradyne.com
Via Telephone: Call our automated call system to receive current information via
fax or to speak with a company representative.
— Within the U.S.A., call 1-800-870-2221
— Outside the U.S.A, call 1-727-530-2340
Document Feedback
We welcome your comments and suggestions about this document. Please mail them
to Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773,
document in your correspondence. Please include your name and phone number if you
are willing to provide additional clarification.
Trademarks
All products and services mentioned herein are the trademarks, service marks,
registered trademarks or registered service marks of their respective owners.
TM
1
COMSPHERE 3600 Series Data Service Units
Time Division Multiplexer, Multichannel Multipoint,
and Digital Bridge Options
Quick Reference
Document Number 3610-A2-GL12-00
November 1998
Product Documentation on the World Wide Web
We provide complete product documentation at www.paradyne.com. This lets you
search the documentation for specific topics and print only what you need, reducing the
waste of surplus printing. It also helps us maintain competitive prices for our products.
Select
Service & Support
→
Technical Manuals
→
Subrate Digital Access Devices
.
Then select the following documents:
3610-A2-GB46
COMSPHERE 3600 Series Data Service Units,
Models 3610 and 3611, User’s Guide
3610-A2-GB48
COMSPHERE 3600 Series Data Service Units,
Models 3610 and 3611 Time Division Multiplexer, Multichannel Multipoint, and
Digital Bridge Options, Supplement
To request a paper copy of a Paradyne document:
Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)
Outside the U.S.A., call 1-727-530-8623
Things to Know Before Installation
The COMSPHERE Model 3610 DSU with the TDM or MCMP option is delivered with
default hardware settings, factory default configuration option settings, and
factory-installed software.
Port 1 of the DSU is preconfigured to operate with the TDM or MCMP capability
enabled. The DSU includes the factory default configuration option settings for
FacT with some defaults based on hardware.
For the Model 3610, all additional ports are disabled and preconfigured for EIA-232
port interface operation. Each port configured for V.35 needs an interconnect cable
(Feature Number 3000-F1-510).
Once a DSD model is powered up, you can verify the port interface switch setting
through the right side of the back panel.
— If set for EIA-232, you will see a green light.
— If set for V.35, you will see a yellow light.
496-15149
2
Installing the DSU
The Model 3610 DSU is designed for desktop operation.
Place the DSU in the planned location.
Allow 1 to 2 feet of clearance for cable connections, space for the ventilation slots
on the sides, and clearance at the rear for the cable connections.
Hardware Settings
!HANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICES
This product is designed to protect sensitive components from
damage due to electrostatic discharge (ESD) during normal
operation. When performing installation procedures,
however, take proper static control precautions to
prevent damage to equipment. If you are not sure
of the proper static control precautions, contact
your nearest sales or service representative.
TDM/Flex and MCMP/Flex models are available with two or six ports. When your
firmware version is 6.33 or greater, each port can be set individually for either EIA-232
or V.35 using the front panel, an async terminal, or an NMS.
Based on your model, you may need to perform one of following procedures. Use ID
from the Status branch to obtain the firmware version.
If your
model is a
6-port . . .
And the
EIA-232
setting . . . Then . . .
TDM/Flex or
MCMP/Flex Is correct Go to
Powering Up the DSU
, page 9.
MCMP/Flex
with firmware
6.33 or
greater
Needs to be
changed Go to
Powering Up the DSU
, page 9, and
Reconfiguring Ports
, page 10.
TDM/Flex or
MCMP/Flex
Is correct Go to
Powering Up the DSU
, page 9.
MCMP/Flex
with firmware
less than
6.33
Needs to be
changed Change the S1 switch setting on the TDM/Flex or
MCMP/Flex circuit card to the On position for V.35 or
Off position for EIA-232.
TDM/DSD or
Is correct Go to
Powering Up the DSU
, page 9.
TDM/DSD or
MCMP/DSD Needs to be
changed Change the option card to set all six ports. Start with
the next section,
Opening the DSU
.
3
Opening the DSU
NOTE:
If the unit is already installed, disconnect all cables, including the power source,
before opening the DSU.
Opening a Model 3610 DSU without MUX
Follow this procedure to separate the DSU cover from the base.
Procedure
1. Turn the unit upside down and release the four snap tabs using a small flat-blade
screwdriver. Tabs release when you push in and up with the screwdriver.
2. Turn the unit upright and bring the cover toward the front panel. Do not allow any
cables to pull free from the inside front panel connectors.
496-14706-02
Snap Tabs
R
UL
R
THISDIGITAL APPARATUSDOES NOT EXCEED THE CLASS A LIMITS FOR RADIO NOISE
EMISSIONSFROM DIGITAL APPARATUSSET OUT IN THE RADIO INTERFERENCE
REGUAALTIONSOF THE CANADIAN DEPARTMENT OF COMMUNICATIONS
FOR USE WITHA CERTIFIED CLASS 2 POWER SUPPLY FOUR UTILISER AVEC LINE
ALIMENTATIONCERTIFEE
EN CLASSE 2.
THISDEVICE COM;OIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO
THEFOLLOWING TWO CONDITIONS (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCEAND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED
INCLUDINGINTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
FCC ID: NOTAPPLICABLE
PEC MFGDATE
MODEL
NO. SER.NO
COMMCODE
MADE IN USA
Snap Tabs
Snap
Tabs
COMSPHERE 3610
4
Opening a Model 3610 DSU with MUX
Follow this procedure to separate the MUX DSU cover from the base and to separate
the DSU circuit card from the MUX circuit card.
Procedure
1. Use a small flat-blade screwdriver to release the four snap tabs holding the base in
place. Tabs release when you push in and up with the screwdriver. Remove the
cover toward the front panel. Do not allow any cables to pull free from the inside
front panel connectors.
496-14707-01
With TDM
or MCMP
Snap Tabs
COMSPHERE 3610
2. Disconnect the LCD flat cable by working the cable free of the connector.
3. Disconnect the keypad flat cable from the DSU circuit card by
squeezing the
latches
on each side of the cable connection and pulling up on the keypad flat
cable.
4. Disconnect the TDM/MCMP flat cable.
5. Unscrew the three screws holding the DSU circuit card in place.
6. Lift the DSU circuit card from the base and set aside.
5
LCD
Flat
Cable
Keypad
Flat
Cable
DSU
Circuit
Card
Expanded
Base
Snap
Tabs
TDM or MCMP
Flat Cable
Screw
98-13846d
Snap
Tabs
Screw
Screw
Assembling and Disassembling a TDM or MCMP DSU
6
Changing the EIA-232 or V.35 Interface
Follow this section to change a TDM/DSD or MCMP/DSD model from:
HEIA-232 interface to V.35 interface, or
HV.35 interface to EIA-232 interface
Separating the DSU from the TDM or MCMP
Follow this procedure to separate the DSU circuit card from the TDM or MCMP.
"Procedure
1. Disconnect the keypad flat cable from the DSU circuit card by
squeezing the
latches
on each side of the cable connection and pulling up on the keypad flat
cable.
2. Disconnect the LCD flat cable by working the cable free of the connector.
3. Disconnect the TDM or MCMP flat cable.
4. Unscrew the three screws holding the DSU circuit card in place.
5. Lift the DSU circuit card from the base and set aside.
Changing the DSD Option Card Setting
For the TDM/DSD or MCMP/DSD model, use the following procedure to change the
setting from EIA-232 to V.35 or from V.35 to EIA-232.
"Procedure
1. Work the option card free of its connector.
Option
Card
Rear
Panel LED 2
(Yellow
V.35)
LED 1
(Green
EIA-232)
496-13845-03
THIS SIDE FACES REAR FOR V.35
S1
S2
2. Turn the card around and re-insert. In the example above, the card reads THIS
SIDE FACES REAR FOR V.35.
7
Adding the MCMP/TDM Flex Option to a
Model 3610 DSU
An MCMP/TDM circuit card assembly (CCA) can be added to an installed DSU. The
MUX CCA must be physically and electrically connected to the DSU. The Model 3610 is
installed into a larger base.
The MCMP/TDM Flex model is designed so that each port can be set individually to
either EIA-232 or V.35 by using either the front panel, an async terminal, or an NMS.
The firmware version must be 6.33 or greater.
Adding a MUX CCA
To upgrade a 3610 DSU with a MUX CCA:
Procedure
1. Fold the TDM/Flex or TDM/Flex flat cable over the side of the new expanded base.
2. Position the DSU over the expanded base.
3. Proceed to
Reassembling the DSU
on page 8.
Replacing an Installed MUX CCA
To replace an existing MUX CCA:
Procedure
1. Release the two snaplocks holding the MUX CCA in the base. Remove the MUX
CCA.
Snaplocks
496-15229
TDM/MCMP
Flat Cable
2. Place the new CCA into the two snaplocks in the base.
8
3. Connect the 40-pin TDM/MCMP flat cable to the new MUX CCA. Fold the flat cable
out over the side of the new expanded base.
4. Proceed to
Reassembling the DSU
.
40-Pin
TDM/MCMP
Flat Cable
496-15230
Snap
Tabs
Reassembling the DSU
Procedure
1. Secure the DSU to the expanded base using the two #4 thread-cutting screws at
the front corners, and the #4 screw with the captive lock-washer at the back corner.
2. Connect the flat cable’s 40-position header to the DSU as shown on page 5.
3. Connect the keypad flat cable by inserting the cable into its connector as far as it
will go, then pushing down on the latching mechanism.
4. Being careful not to bend the pins, align the LCD flat cable with its connector. Push
the cable into place.
5. Align the rear panel and four snap tabs. Replace the cover over the expanded
base, allowing the four tabs to snap into place.
Autres manuels pour COMSPHERE 3610
13
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Paradyne Matériel réseau
Paradyne
Paradyne ACCULINK 3163 DSU Manuel utilisateur
Paradyne
Paradyne 7915-A1 E1 SDSL Manuel utilisateur
Paradyne
Paradyne 5030 Manuel utilisateur
Paradyne
Paradyne COMSPHERE 6700 Series Manuel utilisateur
Paradyne
Paradyne Hotwire 5446 Manuel utilisateur
Paradyne
Paradyne 12000E Manuel utilisateur
Paradyne
Paradyne iMarc DSL 9720 CSU/DSU Manuel utilisateur
Paradyne
Paradyne JetFusion 2208 Manuel utilisateur
Paradyne
Paradyne GranDSLAM 4200 Manuel utilisateur
Paradyne
Paradyne M/HDSL Standalone Termination Unit HOTWIRE... Manuel utilisateur
Paradyne
Paradyne 3163 Manuel utilisateur
Paradyne
Paradyne 3151 Manuel technique
Paradyne
Paradyne Hotwire 5620 Manuel utilisateur
Paradyne
Paradyne COMSPHERE 3810 Manuel utilisateur
Paradyne
Paradyne 8310 MVLt Manuel utilisateur
Paradyne
Paradyne Hotwire 6210 Manuel utilisateur
Paradyne
Paradyne Hotwire 8784 Manuel utilisateur
Paradyne
Paradyne Comsphere 3510 Manuel utilisateur
Paradyne
Paradyne Hotwire 5620 Manuel utilisateur
Paradyne
Paradyne COMSPHERE 6700 Series Manuel utilisateur
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
