Paradyne 5030 Manuel utilisateur
TM
1
HotWire 5030 POTS Splitter Customer Premises
Installation Instructions
Document Number 5030-A2-GN10-10
October 1997
Before You Begin
Verify that:
The local loop POTS service is connected to the POTS/DSL network at the
punchdown block or network interface device (NID).
New or existing unshielded twisted-pair wiring (CAT3 or better) is used with
this product. The CAT3 wiring must meet EIA/TIA-568 specifications with
24 AWG (.5 mm) or 26 AWG (.4 mm).
For RADSL (Rate Adaptive Digital Subscriber Line) RTU installation information, refer to
the appropriate RTU document:
Document Number Document Title
5216-A2-GN10
HotWire 5216 Remote Termination Unit (RTU)
Customer Premises Installation Instructions
5246-A2-GN10
HotWire 5246 Remote Termination Unit (RTU)
Customer Premises Installation Instructions
5446-A2-GN10
HotWire 5446 Remote Termination Unit (RTU)
Customer Premises Installation Instructions
Package Checklist
Verify that your package contains the following:
POTS splitter and housing with closure screw
Small plastic bag with two 8–15 x 1″Type A combination Phillips/slotted-head
screws and two 1″plastic anchors
Warranty card
Tools Required
Flat-blade screwdriver to tighten terminal screws
3/8″nut driver to close housing securely
Phillips-head or combination Phillips/slotted-head screwdriver to mount the housing
Drill and 3/16″drill bit to mount the housing in cement or cinder block
2
What Does the POTS Splitter Do?
The POTS splitter and HotWire Remote Termination Unit (RTU) are components in the
RADSL Access System. This system provides high-speed Internet or corporate LAN
access over traditional twisted-pair copper telephone wiring.
The POTS splitter filters out the DSL signal and allows the POTS frequencies to pass
through. The RADSL RTU and telephone can function simultaneously over the same
pair of copper wires at the customer premises when a POTS splitter is used at both
ends of the local loop.
Copper pairs run from the central office to the customer premises to create the local
loop. The local loop terminates on the customer premises at the demarcation point in a
punchdown block or NID.
Wiring is connected from the demarcation point to the POTS splitter and to the DSL
jack. Wiring also connects the demarcation point to an RJ11 wall jack for DSL access
by the RTU.
97-15346-01
Punchdown
Block or NID
DSL
Jack RTU
New Wiring Connections Existing Wiring (POTS)
Customer Premises (CP)
DSL
Ethernet
Crossover
Cable Ethernet
Cable
or
Central
Office
(CO)
Demarcation
Point
Local Loop
HUB
CP
POTS
Splitter
DSL - Digital Subscriber Line POTS - Plain Old Telephone Service
NID - Network Interface Device RTU - Remote Termination Unit
POTS
End-user
Systems
Network
Service
Provider
(NSP)
97-15247
POTS Splitter Housing
3
Mounting the POTS Splitter Housing
The POTS splitter can be placed:
HOn the outside of the structure near the NID or punchdown block, or
HInside the building.
When mounted outside, the POTS splitter must be installed at or above the height of
the NID, and should be a minimum of three feet above ground.
At the front of the housing, align the housing to open from the right with the rubber
grommet for cable access facing downward. Place the housing upright as shown. Use a
Phillips-head or combination Phillips/slotted-head screwdriver and the screws included
in the package.
If mounting to:
HCement or cinder block: use a drill and
and 3/16″masonry drill bit to install the
two plastic anchors first. Then, install the
two 8–15 x 1″Type A screws.
HWood: install only the two 8–15 x 1″
Type A screws and discard the
plastic anchors.
97-15437-01
Lever
Closure
Screw
4
Preparing the POTS Splitter
"Procedure
1. Unscrew the closure screw and open
the housing by pressing on the lever
on the right above the closure screw.
2. Remove the rubber grommet at the base
of the POTS splitter.
3. Make a small diagonal cut in the rubber
grommet to feed the wiring through.
4. Replace the rubber grommet at the
base of the POTS splitter.
P1 P2 P3 P4
97-15256
Rubber
Grommet
Base of
POTS Splitter
5
Installing the POTS Splitter Wiring
The local loop ends at the punchdown block or NID. Wiring must be connected from the
customer premises (CP) side of the punchdown block or NID to the DSL jack. Typically,
the punchdown block is installed in commercial locations and the NID is installed in
residential locations.
The following is an example of a punchdown block.
ABCD
DSL/POTS
From Local
Loop
Wiring to
DSL Jack
Bridge Clip
Punchdown Block
97-15349
Jumper
Wiring to
POTS Splitter
for POTS
Demarcation Point
Customer Premises
"Procedure
1. Access the punchdown block or NID.
2. Disconnect the POTS access wiring from the local loop.
!WARNING:
Do not continue unless the DSL access line from the local loop has been
disconnected at the NID or punchdown block. Refer to
Important Safety
Instructions,
page 10.
Green (T1) and Red (R1) are the standard pair wiring colors used in the next two
NID illustrations for Tip (T1) and Ring (R1). Your wiring may differ.
6
DSL/POTS
From Local
Loop
Telephone Network Interface Device (NID)
Ground
Tip
T1
(Green)
Ring
R1
(Red)
97-15502
Existing POTS
Wiring to
Telephone
Demarcation Point
Customer Premises
3. Disconnect the POTS wiring to the telephone from the T1/R1 connectors on the
customer premises side.
4. Feed the disconnected POTS wiring through the POTS splitter rubber grommet
access opening created at the base of the POTS splitter. Connect the wiring to the
right side labeled PHONE. Attach green to P3 and red to P4. Tighten both terminal
screws with a flat-blade screwdriver.
97-15257a
P1 P2 P3 P4
LINE PHONE
Red
Green
To
Telephone
POTS Splitter
7
Reconnecting to the Local Loop
"Procedure
1. Feed new jumper wiring through the POTS splitter rubber grommet. Remove the
insulation at the end of the wiring.
2. On the left side labeled LINE, attach red to terminal screw P1 and green to terminal
screw P2. Tighten both terminal screws with a flat-blade screwdriver.
97-15257-01
P1 P2 P3 P4
LINE PHONE
Red Red
Green
Green
New Wiring from
Punchdown
Block or NID
To
Telephone
POTS Splitter
97-15251
Lever
Closure
Screw
8
3. Locate the T1/R1 connectors on the customer premises side of the punchdown
block or NID where the existing POTS wiring was removed in Step 3 on page 6.
Attach the jumper pair from P1/P2 labeled LINE in the POTS splitter to the T1/R1
connectors.
DSL/POTS
From Local
Loop
Wiring to
DSL Jack
Telephone Network Interface Device (NID)
Ground
Tip
T1
(Green)
97-15341
Jumper Wiring to
POTS Splitter
for POTS
Demarcation PointCustomer Premises
Ring
R1
(Red)
4. Snap the lever shut to
close the POTS splitter.
5. Use the 3/8″nut driver
on the closure screw to
securely close the housing.
9
DSL Access Wiring
"Procedure
1. Attach new wiring to the T1/R1 connectors that will go to the DSL jack from the
punchdown block or NID.
2. Tighten the T1/R1 terminal screws with a flat-blade screwdriver.
97-15485
DSL
RJ11
Jack
Central
Office
Punchdown
Block or NID
Customer Premises
POTS/DSL
Local Loop
Demarcation Point
Twisted
Pair Wiring
POTS Splitter
You are now ready to run the specified wiring to the RTU location and install a DSL wall
jack. To install an RTU, refer to the
HotWire 5446 Remote Termination Unit (RTU)
Customer Premises Installation Instructions.
If the RTU is not being installed at this time, reconnect the local loop wiring at the
demarcation point.
10
5030 POTS Splitter Technical Specifications
Item Specification*
Height x Width x Depth 6.65″x 5.44″x 2.25″(16.89 cm x 13.82 cm x 5.72 cm)
Weight 10.2 ounces (289.2 grams)
Approvals
FCC Part 68
Safety Certifications
Refer to the equipment’s label for Registration Number.
Refer to the equipment’s label for approvals on product.
Physical Environment
Operating temperature
Storage temperature
Relative humidity
Shock and vibration
–40°F to 140°F (–40°C to 60°C)
–40°F to 158°F (–40°C to 70°C)
5% to 95% (noncondensing)
Withstands normal shipping and handling
Interface Connectors Four terminal screws
*Technical Specifications subject to change without notification.
Autres manuels pour 5030
2
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Paradyne Matériel réseau
Paradyne
Paradyne Hotwire 8775 Manuel utilisateur
Paradyne
Paradyne COMSPHERE 3610 Manuel
Paradyne
Paradyne COMSPHERE 3610 Manuel utilisateur
Paradyne
Paradyne iMarc FLEX 9123 Manuel utilisateur
Paradyne
Paradyne 3163 Manuel utilisateur
Paradyne
Paradyne 8310 MVLt Manuel utilisateur
Paradyne
Paradyne ACCULINK 316x Manuel
Paradyne
Paradyne 9126 Manuel utilisateur
Paradyne
Paradyne HotWire 7924 Manuel utilisateur
Paradyne
Paradyne COMSPHERE 3550 Series Manuel utilisateur
Paradyne
Paradyne COMSPHERE 3610 Manuel d'exploitation et d'entretien
Paradyne
Paradyne BitStorm IP DSLAM 1900 Manuel du produit
Paradyne
Paradyne Micro Interface Module MIM-2000F Manuel utilisateur
Paradyne
Paradyne BitStorm 2600 Manuel utilisateur
Paradyne
Paradyne Single T1 Network Access Module (NAM)... Manuel utilisateur
Paradyne
Paradyne 7511 Manuel utilisateur
Paradyne
Paradyne HotWire 7924 Manuel utilisateur
Paradyne
Paradyne 7915-A1 E1 SDSL Manuel utilisateur
Paradyne
Paradyne Hotwire 5620 Manuel utilisateur
Paradyne
Paradyne 7510 DSU Manuel d'installation
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
