Outback ONYX 4 Burner Manuel utilisateur
WARNING
• For outdoor use only.
• Read instructions before using the appliance. Failure to follow instructions could
result in death, serious bodily injury, and/or property loss.
• Warning: accessible parts may be very hot. Keep young children away.
• Do not move the appliance during use.
• Turn off the gas supply at the gas cylinder after use.
• Any modification of the appliance, misuse, or failure to follow the instructions
may be dangerous and will invalidate your warranty. This does not affect your
statutory rights.
• Retain these instructions for future reference.
• Leak test your barbecue annually. Check the hose connections are tight and leak
test them each time you reconnect the gas bottle.
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open barbecue lid or hood.
4. If odour continues, discontinue use and
contact your local dealer.
FOR YOUR SAFETY
1. Do not store or use petrol or other flammable
vapours or liquids in the vicinity of this or any
other appliance.
2. A gas cylinder not connected for use shall not
be stored in the vicinity of this or any other
appliance.
Photographs are not to scale.
Specifications subject to change
without prior notice.
Assembly and Operating Instructions for
ONYX 4 Burner with Side Burner Gas Barbecue
0359
2
Pre-Assembled Component
HQuantity varies according to model purchased
sAppearance, size, and construction may differ according to model purchased
CODE PART QTY ONYX 4 Burner with Side Burner
HOOD
A1 Hood (pre-assembled to body) 1 3
A2 Hood Handle 1 3
A3 Heat Indicator Assembly 1 3
A4 WarmingRack 1 3
BODY
B1 Barbecue Body 1 3
B2 Burner 4 3
B3 Control Panel 1 3
B4 Knob (four pre-assembled) 5 3
B5 Side Burner Valve/Hose/Regulator Assembly 1 3
B6 Flame Tamer 2 3
B7 Cooking Grill 1 3
B8 Cooking Griddle 1 3
B9 Ignition Button (one pre-assembled) 2 3
B10 Drip Tray Left Bracket 1 3
B11 Drip Tray Right Bracket 1 3
B12 Drip Tray Handle 1 3
B13 Drip Tray 1 3
TROLLEY
C1 Side Burner 1 3
C2 Side Burner Grid 1 3
C3 Side Burner Shelf 1 3
C4 Knob Bezel (four pre-assembled) 5 3
C5 Side Burner Drip Tray 1 3
C6 Side Shelf 1 3
C7 Cabinet Top Panel 1 3
C8 Cabinet Left Panel 1 3
C9 Cabinet Right Panel 1 3
C10 Cabinet Back Panel 1 3
C11 Cabinet Bottom Panel 1 3
C16 Door 2 3
C17 Door Retaining Spring Axle 2 3
C18 Door Retaining Axle 2 3
C19 Door Catch 2 3
C20 Wheel 2 3
C21 Short Axle 2 3
C22 Hubcap 2 3
C23 Lockable Caster 2 3
HARDWARE
D1 ST4.0X10 Screw 16 3
D2 M4x10 Bolt 4 3
D3 M5x15 Bolt 4 3
D4 M5x35 Bolt 8 3
D5 Ø5 Washer 4 3
D6 M5 Nut 12 3
D7 M6x15 Bolt 12 3
D8 M6x80 Bolt 8 3
D9 M6 Nut 8 3
D10 Body Spacer 8 3
D11
Wi N t
8
3
C12 Left Front Leg 1 3
C13 Left Rear Leg 1 3
C14 Right Front Leg 1 3
C15 Right Rear Leg 1 3
Parts List
Quantities vary according to model purchased. Specifications subject to change without prior notice.
3
Parts Diagrams
Quantities vary according to model purchased. Specifications subject to change without prior notice.
B3
C3
B10
A2
A1
A3
B1
B2
B6
B7
C6
C20 C23
D6
B4
A4
B5
B4
B8
B9
B11
B12
B13
C1
C2
C4
C5
C7
C8 C9
C10
C11
C12 C13
C14
C15
C16C17
C18
C19
C21
C22
4
Assembly
IMPORTANT!
• Tools Required: Medium size flat blade or Phillips/Crosspoint screwdriver, adjustable spanner or metric
spanner set
• The assembly of this barbecue requires 3 people.
• Carefully unpack the parts from the box and remove all internal packaging before commencing
assembly. All loose items including the grills, flame tamers and warming rack must be removed from the
body.
• Whilst every care is taken in the manufacture of this product, care must be taken during assembly in
case sharp edges are present.
1
2
Attach the Left and Right Legs (C12, C13, C14, C15) to the Cabinet Bottom Panel (C11) using
the M5x35 Bolts (D4) and M5 Nuts (D6) as shown. (The bottom panel with door catch
assembling hole should be located at front after assembly)
Insert Short Axles (C21) through Wheels (C20), Axle Washers (D12) and guide holes in left legs and
secure with M8 Nuts (D13). Screw the Lockable Caster (C23) into the end of the right legs and hand
tighten until it stops. Snap the Hubcaps (C22) into wheels.
L/H R/H
L/H R/H
5
Attach the Cabinet Back Panel (C10) onto rear legs using ST4.0x10 Screws (D1) as shown.
4
3
Attach the Cabinet Left Panel (C8) and Cabinet Right Panel (C9) onto the bottom panel
and legs using ST4.0x10 Screws (D1) as shown.
L/H R/H
ST4.0x10 Screw
ST4.0x10 Screw
L/H R/H
6
Attach the Cabinet Top Panel (C7) onto left panel and right panel using M6x15 Bolts
(D7) and M6 Nuts (D9).
6
5
Attach the Door Catches (C19) to the top and bottom panels using M6x15 Bolts (D7) and
M6 Nuts (D9).
7
Attach the Side Shelf (C6) and Side Burner Shelf (C3) using M6x15 Bolts (D7) as shown.
NOTE: Side table supports have slots for easy assembly.
Align guide holes in side table supports, holes in legs, then insert eight M6x80 Bolts
(D8) through the aligned holes, Body Spacers (D10). Do not let the bolts over the
spacers, it is easy to attach body to cabinet assembly.
Place hood and body assembly onto position, screw the bolts through both sidewall of
body and secure with Wing Nuts (D11) as shown. (Three people required)
8
7
R/H L/H
Body Spacer
8
Attach the valve of Side Burner Valve/Hose/Regulator Assembly (B5) and Knob Bezel (C4)
onto side burner shelf using M4x10 Bolts (D2) as shown.
10
9
Attach Drip Tray Right Bracket (B11) onto body using M5x15 Bolts (D3) , Ø5 Washers (D5)
and M5 Nuts (D6) as shown. Repeat for Drip Tray Left Bracket (B10). Make sure that the
tabs which stop drip tray should be located at front.
M5 Nut
9
12
11
Unscrew the retaining nut from Ignition Button (B9), insert the button through the hole beside
side burner knob and secure with the retaining nut.
Connect the ignition wire onto end of ignition button.
Feed the venturi tube of the Side Burner (C1) through the hole in the side burner shelf, and
slide the end of the venturi tube over the tip of the valve. Fix side burner onto bottom of side
burner shelf using a M4x10 Bolt (D2) as shown.
10
14
13
Place the Side Burner Grid (C2) onto the burner.
Press the Burner Knob (B4) on the vale stem.
Attach Side Burner Drip Tray (C5) onto bottom of side burner shelf using a M4x10 Bolt (D2).
Table des matières
Autres manuels Outback Gril
Outback
Outback RC4341C Manuel utilisateur
Outback
Outback Excel Onyx 2 Manuel utilisateur
Outback
Outback Phoenix 4 Burner Black Manuel utilisateur
Outback
Outback Mayfair Manuel utilisateur
Outback
Outback Omega 150 Manuel utilisateur
Outback
Outback EX200T Manuel utilisateur
Outback
Outback Senator 6 Manuel utilisateur
Outback
Outback Trooper Select 2 Manuel utilisateur
Outback
Outback Spectrum 2 Burner Manuel utilisateur
Outback
Outback Meteor Stainless Steel 4 Manuel utilisateur
Outback
Outback THG3302S Manuel utilisateur
Outback
Outback Omega 100 Manuel utilisateur
Outback
Outback Meteor MT-H4430-3 Manuel utilisateur
Outback
Outback RS4491A Manuel utilisateur
Outback
Outback Omega 201 Manuel utilisateur
Outback
Outback THG3302S-3 Manuel utilisateur
Outback
Outback Roast Box 500 Manuel utilisateur
Outback
Outback CK578T Manuel utilisateur
Outback
Outback Outback Excel 210 Manuel utilisateur
Outback
Outback Spectrum 2 Burner Manuel utilisateur
