OPTI-UPS Power PS1000C Manuel utilisateur

User Guide

Power Series

Models PS1000C, PS1250C, PS1500C

PS2000C, PS3000C

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

CAUTION (UPS Having Internal Batteries):Risk of electric

shock - Hazardous live parts inside this unit are energized from the battery

supply even when the input AC power is disconnected.

CAUTION (No User serviceable Parts): Risk of electric shock,

do not remove cover. No user serviceable parts inside. Refer servicing to

qualified service personnel.

CAUTION (Non-isolated Battery supply): Risk of electric

shock, battery circuit is not isolated from AC input, hazardous voltage may

exist between battery terminals and ground. Test before touching.

WARNING (Fuses): To reduce the risk of fire, replace only with the

same type and rating of fuse.

WARNING: Intend for installation in a controlled environment.

CAUTION: Do not dispose of batteries in a fire, the battery may explore.

CAUTION: Do not open or mutilate the battery, released electrolyte is

harmful to the skin and eyes.

CAUTION: A battery can present a risk of electric shock and high short

circuit current. The following precaution should be observed when working on

batteries

Remove watches, rings or other metal objects.

Use tools with insulated handles.

To reduce the risk of electric shock, disconnect the UPS from the mains

supply before installing a computer interface signal cable. Reconnect the

powers cord only after signaling interconnections have been made.

Servicing of batteries should be performed or supervised by personnel

knowledge of batteries and the required precautions. Keep unauthorized

personnel away from batteries

When replacing batteries, replace with four 12V/7Ah

TABLE OF CONTENTS

Important Safety Instructions .....................................................................................................2

Introduction.................................................................................................................................3

1. Presentation...........................................................................................................................5

2. Installation..............................................................................................................................8

3. Operation................................................................................................................................9

4. Alarm....................................................................................................................................10

5. Software and Interface Port .................................................................................................10

6. Maintenance and Storage....................................................................................................14

7. Battery and Battery Cabinet.................................................................................................14

Appendix A. Troubleshooting...................................................................................................15

Appendix B. Specification ........................................................................................................16

INTRODUCTION

SAVE THESE INSTRUCTIONS

Please read and save this manual!

Thank you for selecting this uninterruptible power system (UPS). It provides you with a

perfect protection for connected equipment. The manual is a guide to install and use the

UPS. It includes important safety instructions for operation and correct installation of the

UPS. If you should have any problems with the UPS, please refer to this manual before

calling customer service.

Please save or recycle the packaging materials!

The UPS‘s shipping materials are designed with great care to provide protection within

delivery. These materials are invaluable if you ever have to return the UPS for service.

Damage happened during transit is not covered under the warranty.

Intelligent microprocessor control

The product is an advanced line-interactive UPS based on microprocessor control. This

means that it operates with the newest technology, high performance and powerful function.

The line-interactive UPS is an intelligent protector and provides pure, reliable AC power to

the critical loads - protecting them from utility power blackout, swells, sags, surges and

interference. The loads could include sensitively medical instruments, computers,

telecommunication systems, and industrially automatic equipment. Under power normal

condition, the line-interactive design enables the system to adjust and filter power

fluctuations continuously and automatically. In the event of power failure, it can provide

immediately back-up power from the batteries without any interruption. Complete

transference will be achieved within 4m seconds, with no interruption.

Beside this, when the utility power is connected, the charger would work automatically even

under power switch is OFF. Furthermore, in order to save the battery energy, UPS can

automatically turn it off under backup mode if none of the connected loads is operating.

Advanced battery management

The visual and audible indications of the UPS present the battery’s status including capacity

degree and battery condition. Self-test function let UPS detect a weak battery before it is put

into service. The UPS normally perform a self-test at power up and manual self-test

condition. Self-test function can be conducted manually with the ON/TEST switch at any

time.

Advanced monitoring software

The line-interactive UPS and SENTINEL series monitoring software (optional kits) make

your computer operate intelligent and provide you with the ability of perfect protection of

your critical devices. The software is available for most operation systems and is supplied

with a communication cable that connects to the UPS.

Note: There is no guarantee that interference to radio/TV will not occur in a particular

installation. If this UPS causes interference to radio or television reception, which can be

determined by turning the UPS off and on, the user is encouraged to try to correct the

interference by one or more of following measures:

1. Connect the equipment to an outlet at a circuit different from the connected radio/TV.

2. Increase the separation between the equipment and the receiver or reorient the receiving

antenna.

1. PRESENTATION

1.1 Front LED Panel

For 1-3KVA

n“ON/TEST” button:

With the UPS plugged in, press the ON/TEST button to turn on the UPS and power the

loads. ON/TEST also activates the UPS‘s self-test and utility line voltage displays.

o“OVERLOAD” indicator (RED LED):

The LED lights when the loads connected to the UPS exceed the UPS‘s capacity.

p“BACK UP” indicator (GREEN LED):

The LED illuminates when the UPS is supplying battery power to the loads.

q“REPLACE BATTERY” indicator (RED LED):

The LED illuminates when the UPS‘s battery is no longer useful and must be replaced.

Note: When replace battery, disconnect the utility power then open the case and take notice

of the battery‘s polarity while install the new battery to avoid short circuit.

r“BUCK AVR (VOLTAGE REDUCTION)” indicator (YELLOW LED):

The LED illuminates when the UPS is correcting a high utility voltage condition. The loads

receive normal power.

s“LINE NORMAL” indicator (GREEN LED):

The LED illuminate when the line input voltage is normal.

t“BOOST AVR (VOLTAGE BOOST)” indicator (YELLOW LED):

The LED illuminates when the UPS is correcting a low utility voltage condition. The loads

receive normal power.

_LOAD bar graph:

The display shows the power being drawn by the load.

`POWER bar graph (BATTERY CHARGE):

The display shows the present battery charge as a percentage of battery capacity.

a“OFF” button:

Press the OFF button to turn off the UPS and the loads.

Load Indicator

Light no.5

Light no.4

Light no.3

Light no.2

Light no.1

% of Load Value

over 96%

76-95 %

51-75 %

26-50 %

10-25 %

Battery Indicator

Light no.5

Light no.4

Light no.3

Light no.2

Light no.1

% of Bat Level

over 91 %

76-90 %

51-75 %

26-50%

0-25%

1.3 Rear Panel

For 1-2KVA

For 3KVA

nTEL/MODEM connector

Telecom transfer ports provide users to extend the applications.

CAUTION: To reduce the risk of fire, use only No. 26AWG or larger telecommunication

line cord.

oEXTERNAL BATTERY PACK CONNECTOR (optional)

CAUTION: Use only factory supplied or authorized connecting cable for external battery!

pOUTPUT POWER RECEPTACLES

qAC INPUT POWER RECEPTACLE

rINPUT CIRCUIT BREAKER

It trips when the connected loads exceed the protected receptacle‘s capacity, The center

plungers of the circuit breakers extend when tripped.

sRS232 INTERFACE

Provide both RS-232 and relay signal to support NOVELL, UNIX, DOS, WINDOWS and

other operating systems.

tSNMP INTERFACE PORT (optional)

Provide the SNMP adapters for 10-BaseT Ethernet and Token Ring connectors. Through the

SNMP adapter, your UPS becomes “SNMP manageable”. It provides a real time UPS and

power status information for the network manager.

CAUTION: Use only factory supplied or authorized SNMP monitoring cable!

_USB INTERFACE

Provide USB signal to support WINDOWS 98SE/Windows 2000/Widnows XP/Windows

NT4.0 operating systems.

2. INSTALLATION

Inspect the UPS upon receipt. The packaging is recyclable; keep it for reuse or be

disposed of properly.

2.1 Placement:

Install the UPS in a protected area with adequate flowing air and free of excessive dust.

Do not operate the UPS where the temperature and humidity is out of the specified limits.

2.2 Connect Computer Interface (optional):

SENTINEL series software (or other power management software) and an interface kits

can be used with this UPS. Use only kits supplied or approved by the manufacturer. If

used, connect the interface cable to the 9-pin computer interface port on the back panel of

the UPS.

Note: Computer interface connection is optional. The UPS works properly without a

computer interface connection.

CAUTION: Use only factory supplied or authorized UPS monitoring cable!

2.3 Connect external battery pack (optional):

Before connecting, make sure the external battery pack and the connector cable are

compatible.

Note: External battery connection is not necessary. The UPS works properly without

external battery pack connection. (Except AL models only)

CAUTION: Use only factory supplied or external battery connection cable!

2.4 Charge the battery:

The UPS charges its battery whenever it is connected to utility power. For best results,

charge the battery for 8 hours in the initial use.

2.5 Connect to Utility:

See figure a. Please check the following items to connect the AC input power to terminal

block and power up the UPS.

2.6 Connect the loads:

Connect the loads with the terminal block at the rear of the UPS. To use the UPS as a

master on/off switch, make sure all of the loads are switched on.

CAUTION: Never connect a laser printer or plotter to the UPS with other computer

equipment. A laser printer or plotter periodically draws significantly more

power than when its idle status, and may overload the UPS.

2.5cm (1 inch)

3. OPERATION

3.1 Switch on:

While utility input is connected to the UPS, press the "ON" button and keep

pressing over than 0.5 second. After that, connect the electrical cords of the

equipment that is going to be used such as computer or monitor with the terminal

on the rear panel of UPS.

Don't overload the machine with all the equipment used. The buzzer will beep continuously

to indicate overload status. UPS will shut down automatically to protect the machine.

Attention: If the power of UPS isn't supplied by utility but by the internal batteries to

engage the UPS, press the "ON" button and keep pressing for over 3 seconds.

CAUTION: Never connect a laser printer or plotter to the UPS with other computer

equipment. A laser printer or plotter periodically draws significantly more power than when

its idle status, and may overload the UPS.

3.2 Switch off:

By pressing and holding OFF button until the “LINE NORMAL” or “BACK UP” LED off.

3.3 Silence:

When UPS is under “BACKUP” mode, press “ON” button more than 1 second to silence

the audible alarm. (The function is disable when UPS is under condition of “LOW

BATTERY” or “OVERLOAD”)

Note: At back-up mode, UPS can be automatically turned off if none of the connected loads

is operating.

3.4 Self-test:

Use the self-test to verify both the operation of the UPS and the condition of the battery. In

normal utility power, push the ON/TEST button more than 1 second and UPS performs a

self-test function. During the self-test, the UPS operates a back up mode.

Note: During the self-test, the UPS briefly operates the loads on-battery (the on-battery LED

comes on).

If the UPS passed the self-test, it returns to line-interactive operation. The on-battery LED

goes off and the line-interactive LED goes on steadily. If the UPS is failed to pass the

self-test, it returns to line-interactive operation and lights the replace battery LED. The loads

are not affected. Recharge the battery overnight and perform the self-test again. If the

replace battery LED is still on, ask our nearest dealer to replace battery.

3.5 Load bar graph:

The 5-LED display shows the power drawn from the UPS by load. The display indicates the

percentage of the UPS‘s rated capacity. For example. If three LEDs are lit, the load is

drawing between 50% and 67% of the UPS’s capacity. If the UPS is overloaded, the

overload LED lights and alarm sounds.

3.6 Battery charge bar graph:

The 5-LED display shows the present charge of the UPS‘s battery as a percentage of the

battery capacity. When all five LEDs light, the battery is fully charged. When only two LED

lights, the battery can supply less than two minutes of run time for the load.

3.7 Cold start:

When the UPS is off and there is no utility power, use the cold start feature to apply power

to the loads from UPS‘s battery. Press the ON/TEST button until the UPS beeps.

3.8 Shutdown mode:

In shutdown mode the UPS stops supplying power to the load, waiting for return of utility

power. If there is no utility power present, external devices (e.g., servers) connected to the

computer interface can command the UPS to shutdown. This is normally done to preserve

battery capacity after the graceful shutdown of protected servers. The UPS will scroll the

front panel indicators sequentially in shutdown mode.

4.ALARM

4.1 “BACKUP”(slow alarm):

When the UPS is working under “BACKUP” mode, the UPS would emit audible alarm. The

alarm stops when the UPS is return to “LINE” mode operation. Anyone can stop the alarm

by press the “ON” button during backup mode.

Attention: The alarm of “BACKUP” is going to beep every four seconds. (Slow-speed

beep).

Attention: The UPS provides mute function for the warning. When the beeping sound

occurs, press "ON" to stop it; and press "ON" again to regain the sound.

4.2 “LOW BATTERY” (rapid alarm):

In the “BACKUP” mode, when the energy of battery becomes to lower level. (about

20%~30%) The UPS beeps rapidly until the UPS shuts down from battery exhaustion or

returns to “LINE” mode operation.

Attention: The alarm of the batteries caused by low voltage beeps every second.

(Fast-speed beep).

Attention: The rapid alarm under “LOW BATTERY” condition can't be erased.

When the UPS is working under overload condition (the connected loads exceed the

maximum rated capacity), the UPS will emit continuous alarm to warn an overload

condition. In order to protect the unit and the loads, the UPS will be automatic shutdown.

Disconnect nonessential devices from UPS to eliminate the overload alarm.

5. SOFTWARE AND INTERFACE PORT

5.1 Power Monitoring Software

The SENTINEL series software is applied standard RS-232 or USB interface to perform

monitoring functions, and then provides an orderly shutdown of a computer in the event of

power failure. Moreover, SENTINEL displays all the diagnostic symptoms on monitor,

such as Voltage, Frequency, Battery level and so on. For RS-232 interface, the software is

available for Windows 95, Windows 98, Windows Me, Windows 2000, Windows XP,

Windows NT 4.0 or later, Novell Netware, Linux, and others. For USB interface, the

software is available for Windows 98SE, Windows 2000, Windows Me, Windows XP,

Windows NT4.0 or later. Call your dealer for more information on computer OS

compatible solutions.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels OPTI-UPS UPS

OPTI-UPS

OPTI-UPS VS375C Manuel utilisateur

OPTI-UPS

OPTI-UPS Standby UPS System Manuel utilisateur

OPTI-UPS

OPTI-UPS Inverter Series IS1100LT Manuel utilisateur

OPTI-UPS

OPTI-UPS IS1100NR Manuel utilisateur

OPTI-UPS

OPTI-UPS Power PS500C Manuel utilisateur

OPTI-UPS

OPTI-UPS High-Frequency Online UPS DS1000E Manuel utilisateur

OPTI-UPS

OPTI-UPS VS375C Manuel utilisateur

OPTI-UPS

OPTI-UPS Thunder Shield TS500D Manuel utilisateur

OPTI-UPS

OPTI-UPS DS-D33 Manuel utilisateur

OPTI-UPS

OPTI-UPS On Line UPS Series DS100KC33 Manuel utilisateur

OPTI-UPS

OPTI-UPS High-Frequency Online UPS DS1000E Manuel utilisateur

OPTI-UPS

OPTI-UPS DC12V Manuel utilisateur

OPTI-UPS

OPTI-UPS ES1000C-RM Manuel utilisateur

OPTI-UPS

OPTI-UPS On Line UPS Series DS10000B Manuel utilisateur

OPTI-UPS

OPTI-UPS OD330 Manuel utilisateur

OPTI-UPS

OPTI-UPS Thunder Shield Manuel utilisateur

OPTI-UPS

OPTI-UPS PS650D Manuel utilisateur

OPTI-UPS

OPTI-UPS Excalibur 5000AL Manuel utilisateur

OPTI-UPS

OPTI-UPS Power PS800B Manuel utilisateur

OPTI-UPS

OPTI-UPS On Line UPS Series DS10KB-RM Manuel utilisateur

OPTI-UPS

OPTI-UPS IS1700NT Manuel utilisateur

OPTI-UPS

OPTI-UPS DS-I Series Manuel utilisateur

OPTI-UPS

OPTI-UPS DS-D33 Manuel utilisateur

OPTI-UPS

OPTI-UPS DS-C33 Series Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur