NXP Semiconductors SLN-VIZNLC-IOT Manuel utilisateur

SLN-VIZNLC-IOT-GSG

SLN-VIZNLC-IOT Getting Started Guide

Rev. 0 — 10 March 2023 User guide

Document information

Information Content

Keywords SLN-VIZNLC-IOT-GSG, Smart Lock, IoT

Abstract This guide walks you through the process of getting up and running with your SLN-VIZNLC-IOT

board

NXP Semiconductors SLN-VIZNLC-IOT-GSG

SLN-VIZNLC-IOT Getting Started Guide

1 Plug it in

Welcome to the SLN-VIZNLC-IOT Getting Started Guide.

This guide walks you through the process of getting up and running with your SLN-VIZNLC-IOT board. This

guide takes you through the steps of unboxing your kit, running the out-of-box smart lock demo application, as

well as downloading, modifying, and debugging the firmware source code for your kit.

Before we begin, make sure to check the box your kit came in for any marks or other damages, and should you

find anything, be sure to report it to your local NXP representative.

2 Smart Lock

2.1 Unbox

The box your kit arrives in should contain a few different things, including:

•A packing list paper

•Fully assembled VIZNLC kit

•USB-A > USB-C Cable (x1)

•Jumpers (x2)

Figure 1. Items inside the box

2.2 Power on

Before we begin, put a jumper on J3 (pin 2 and 3 on the left side) as shown in the yellow highlighted box in

Figure 35. Then remove the protective film from the RGB and IR camera as shown in Figure 2. This protective

film is used to protect the lens of each camera during transport. However, failure to remove may cause the

image capture not to work correctly.

User guide Rev. 0 — 10 March 2023

2 / 23

NXP Semiconductors SLN-VIZNLC-IOT-GSG

SLN-VIZNLC-IOT Getting Started Guide

Figure 2. Protective film covering the two cameras: RGB and IR

To get started, follow the steps below:

1. Take the USB-A > USB-C cable provided inside the kit. Plug the USB-A end into USB port on your computer

and the USB-C end into the USB port of the kit. The USB connector of the kit supplies power to the board

and supports data transfer capabilities for Mass Storage Device (MSD) programming and virtual serial port

communication.

Figure 3. Power on the SLN-VIZNLC-IOT kit

2. Once the application is ready, your computer detects a new USB COM device, and automatically installs the

required drivers. A message confirms when the installation is completed.

3. After powering on, the onboard TFT screen streams video directly from the RGB camera alongside a GUI

overlay, providing information such as:

•Locked/Unlocked status whether a face is recognized

•Current App Type (Smart Lock/Access)

•ON/OFF status of Wi-Fi and Bluetooth LE

•Number of registered users

User guide Rev. 0 — 10 March 2023

3 / 23

NXP Semiconductors SLN-VIZNLC-IOT-GSG

SLN-VIZNLC-IOT Getting Started Guide

Figure 4. The screen with video preview

2.3 Register and recognize a face

Let us get started with a demonstration of the out-of-box features of this application.

To use the recognition feature of the SLN-VIZNLC-IOT, a face must be registered in the local face database of

the kit. To begin registering a new face, press the Manual Registration button (SW4) on the kit.

Figure 5. Manual Registration button (SW4)

Once pressed, a message indicating registration is taking place pops up at the top of the screen. The speaker

plays an audio message confirming that the registration has started.

User guide Rev. 0 — 10 March 2023

4 / 23

NXP Semiconductors SLN-VIZNLC-IOT-GSG

SLN-VIZNLC-IOT Getting Started Guide

Figure 6. Registering screen

Figure 6 shows that while registration is taking place, the GUI displays:

•A “Registering” message

•Face alignment guidelines

•A countdown timer bar

The guidelines help you align your face correctly during registration, and the countdown timer bar indicates how

much longer it takes until the registration process times out and fails.

Figure 7. Registration Timeout

As an additional measure to help with registering your face, the kit even plays a warning audio prompt if too

much of the side of your face is exposed during the registration process, saying “Look at Camera”. The kit plays

this warning audio until your face is properly pointed toward the camera.

Should your face fails to register, simply press the SW4 button again to retry.

Once your face is successfully registered, the kit displays the message "Registration Successful", and a unique

identifier is assigned to your face. The number of registered users is also updated automatically.

User guide Rev. 0 — 10 March 2023

5 / 23

NXP Semiconductors SLN-VIZNLC-IOT-GSG

SLN-VIZNLC-IOT Getting Started Guide

Figure 8. Registration Successful

Once registered, the kit displays the message “Recognition Successful” and plays a corresponding audio file

when a recognized face is detected.

Figure 9. Recognition Successful

2.4 Liveness detection and anti-spoofing

The Liveness detection and anti-spoofing features of the SLN-VIZNLC-IOT are switched ON by default.

Therefore, enabling the system to distinguish between your actual face and a printout or phone display image of

your face.

This feature helps to defend against some of the most frequent face recognition "spoof" attacks.

One such spoof attack is when a malicious actor uses a picture of someone to gain access to their face-

protected materials. The malicious actor does this spoof by requiring an actual face of the user to unlock the

system rather than simply a picture of their face.

User guide Rev. 0 — 10 March 2023

6 / 23

NXP Semiconductors SLN-VIZNLC-IOT-GSG

SLN-VIZNLC-IOT Getting Started Guide

Figure 10. Printed picture and phone display spoof attack

As shown in Figure 10 using a phone display or a printed picture of a face does not trigger the “Recognition

Successful” message.

2.5 Connect to serial CLI

The Smart Lock software installed by default on the SLN-VIZNLC-IOT kit provides a convenient serial-based

CLI. This CLI is used to retrieve useful runtime data and configure various application settings. Connecting to

the serial-based CLI of the kit can be done using a serial terminal emulator program like PuTTY or Tera Term.

Before we begin, make sure that you have a serial terminal emulator like PuTTY or Tera Term installed on your

computer.

Figure 11. PuTTY and Tera Term

Note: If you are using a Windows machine, we recommend Tera Term for its ability to discover connected COM

devices automatically. Additionally, if there is a disconnect, Tera Term reconnects to a device.

Establish a serial connection with your device by entering the serial settings as shown in Figure 12. Ensure to

replace the COM port setting with the COM port associated with your kit.

User guide Rev. 0 — 10 March 2023

7 / 23

NXP Semiconductors SLN-VIZNLC-IOT-GSG

SLN-VIZNLC-IOT Getting Started Guide

Figure 12. Serial port setup

Once connected, a blank terminal screen appears that echoes back any characters that you type. Typing the

help command prints a list of all available commands and a brief description of their functionalities.

Figure 13. Help menu

3 Build and run

3.1 Getting MCUXpresso IDE

The MCUXpresso IDE brings developers an easy-to-use eclipse-based development environment for NXP

MCUs based on Arm Cortex-M cores, including its general-purpose crossover and wireless-enabled MCUs.

User guide Rev. 0 — 10 March 2023

8 / 23

NXP Semiconductors SLN-VIZNLC-IOT-GSG

SLN-VIZNLC-IOT Getting Started Guide

The MCUXpresso IDE offers advanced editing, compiling, and debugging features. It also offers MCU-specific

debugging views, code trace and profiling, multicore debugging, and integrated configuration tools.

To download MCUXpresso IDE, follow the steps below:

1. Go to MCUXpresso IDE homepage and click the Downloads button.

Figure 14. MCUXpresso IDE homepage

2. The Downloads page appears. Next, click the Download button.

Figure 15. Downloads page

3. The Sign In page appears. Login with your credentials.

Figure 16. Sign In page

User guide Rev. 0 — 10 March 2023

9 / 23

NXP Semiconductors SLN-VIZNLC-IOT-GSG

SLN-VIZNLC-IOT Getting Started Guide

4. Once you have signed in, select Version 11.6.1 or newer from the list.

Figure 17. Select Version page

5. The Software Terms and Conditions page appears. Read the conditions and click the I Agree button.

Figure 18. Software terms and conditions page

6. The Product Download page appears from where you can download the MCUXpresso IDE. Download the

appropriate version for your system.

Figure 19. Product Download page

User guide Rev. 0 — 10 March 2023

10 / 23

Table des matières

Autres manuels NXP Semiconductors Matériel informatique

NXP Semiconductors

NXP Semiconductors RD9Z1-638BJBEVM Manuel utilisateur

NXP Semiconductors

NXP Semiconductors freescale MC9S12G128 MCU Manuel utilisateur

NXP Semiconductors

NXP Semiconductors i.MX 8M Manuel d'installation

NXP Semiconductors

NXP Semiconductors PowerQUICC MPC8308_RDB Manuel utilisateur

NXP Semiconductors

NXP Semiconductors SABRE i.MX 6 Series Instructions de montage

NXP Semiconductors

NXP Semiconductors PN7150 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors MCU-SMHMI-UG Manuel utilisateur

NXP Semiconductors

NXP Semiconductors OM15080-K32W Manuel utilisateur

NXP Semiconductors

NXP Semiconductors AN11211 Guide de dépannage

NXP Semiconductors

NXP Semiconductors MPC5775B Manuel utilisateur

NXP Semiconductors

NXP Semiconductors UM10301 PCA2125 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors QorIQ LS1028A Manuel utilisateur

NXP Semiconductors

NXP Semiconductors i.MX 8QuadXPlus Manuel utilisateur

NXP Semiconductors

NXP Semiconductors S32G-VNP-EVB3 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors FRDM-MCXN947 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors UM11653 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors KTTWR17510EVBUG Manuel utilisateur

NXP Semiconductors

NXP Semiconductors MR-CANHUBK344 Instructions d'utilisation

NXP Semiconductors

NXP Semiconductors HVP-56F80748-UM Manuel utilisateur

NXP Semiconductors

NXP Semiconductors UM10694 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors MSC8113 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors freescale MCF5225X Manuel utilisateur

NXP Semiconductors

NXP Semiconductors OM11058 Manuel utilisateur

NXP Semiconductors

NXP Semiconductors AN12398 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur