Norac UC4+ Manuel utilisateur
Summers Main Lift & Enhanced Stability Option
Installation Manual (3-bolt)
Spray Height Controller
Improving the competitiveness of Industry and Agriculture
throu
g
h Precision Measurement
Printed in Canada
Copyright 2010 by NORAC Systems International Inc.
Reorder P/N: UC4+SM3-3B-INST Rev B (Summers Main Lift and Enhanced Stability Kit
– 44952D)
NOTICE
NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and without
the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information
contained in this manual. The technical information in this manual was reviewed at the time of approval for publication.
TABLE OF CONTENTS
1INTRODUCTION ................................................................................................................................. 1
2PARTS LISTS......................................................................................................................................... 2
3HYDRAULIC INSTALLATION........................................................................................................... 5
4ELECTRICAL INSTALLATION.......................................................................................................... 7
4.1ROLL SENSOR INSTALLATION......................................................................................................... 7
4.2ELECTRICAL INSTALLATION ........................................................................................................... 8
5COMPLETING THE INSTALLATION............................................................................................... 9
6ELECTRICAL REFERENCE – CABLE DRAWINGS....................................................................... 10
6.1ITEM C05: 44674 –CABLE UC3 SENSOR ROLL BIAS .................................................................. 10
6.2ITEM C17: 44658-45D –CABLE VALVE UC4 BC MAIN DT........................................................ 11
1
1 INTRODUCTION
Congratulations on your purchase of the NORAC UC4+ Spray Height Controller. This system
is manufactured with top quality components and is engineered using the latest technology to
provide operating features and reliability unmatched for years to come.
When properly used the system can provide protection from sprayer boom damage, improve
sprayer efficiency, and ensure chemicals are applied correctly.
Please take the time to read this manual completely before attempting to install the system. A
thorough understanding of this manual will ensure that you receive the maximum benefit from
the system.
YOUR INPUT CAN HELP MAKE US BETTER! If you find issues or have
suggestions regarding the parts list or the installation procedure, please don’t
hesitate to contact us.
NOTICE:
Every effort has been made to ensure the
accuracy of the information contained in
this manual. All parts supplied are selected
specially to fit the sprayer to facilitate a
complete installation. However, NORAC
cannot guarantee all parts fit as intended
due to the variations of the sprayer by the
manufacturer. Please read this manual
in its entirety before attempting
installation.
ATTENTION:
When installing the UC4+ Spray Height
Control system please be aware that at a
point in the installation your sprayer booms
will be inoperative until the installation is
complete. Any installation procedure
requiring boom movement will need
to be done first. Once the hydraulics
have been disconnected you must complete
the electrical installation before the booms
become operative.
2
2 PARTS LISTS
The parts that come with your Summers Main Lift and Enhanced Stability System are listed in Table 1.
The item number on the left side of this table references each part.
Please ensure that all parts in your kit are present before proceeding with your installation.
Table 1 – Summers Main Lift and Enhanced Stability System Parts
Item Part Number Name Quantity
C05 44674 CABLE UC3 SENSOR ROLL BIAS 1
C17 44658-45D CABLE VALVE UC4 BC MAIN LIFT 1
E01 45001* UC4 PLUS ROLL SENSOR VER. 2 1
H01 44863-01 HOSE ASSEMBLY 122R2-06 36 IN L 6FJX 6FJX 1
H20 44865-50 HYDRAULICS FITTING KIT - SM3 1
M01 44706-01 KIT CABLE TIE BLACK 10 PCS 21 IN 150 PCS 7.5 IN 1
M10 UC4+SM3-3B-INST
MANUAL INSTALLATION UC4+ SUMMERS MAIN LIFT & ENHANCED STABILITY KIT - 44952D
1
V01 44952D VALVE ASSEMBLY SINGLE STATION EXPANSION PROPORTIONAL 1
* For systems purchased BEFORE October 1, 2011, the roll sensor part number is 44642.
3
Table 2 - 44865-50 (Rev A) - Hydraulics Fittings Kit Details
Item Part Number Name Quantity
Picture
F02 103839 TEE - 6FJXR 6MJT 1
F03 104369 PLUG - 6MBP 1
F04 103312 MALE ADAPTER - 6MB 6MJ 1
6 M B - 6 M OR X 90
SIZE IN
1/16TH'S
GENDER: MALE
OR FEMALE
90° ANGLE
SWIVEL
TYPE
GENDER
SIZE
TYPE:
B - ORB
J - JIC
OR - FLAT
FACE
P - PIPE
Fitting Name
Example:
The use of dielectric grease is not recommended on any NORAC electrical connections.
To ensure all stainless steel hardware does not gall or seize apply a light coating of the
supplied Permatex Anti-seize grease to all threaded parts upon installation. Permatex
Anti-seize lubricant is preferred, but other similar anti-seize products may be used.
4
Figure 1 - Hydraulic Plumbing Schematic
5
3 HYDRAULIC INSTALLATION
WARNING!
The hydraulic system creates very
high pressure. Before disconnecting
any hydraulic lines ensure all pressure
has been bled from the system.
IMPORTANT:
Component failure due to oil
contamination is not covered under
the UC4+ Spray Height Control
system warranty. It is recommended
that a qualified technician does the
hydraulic installation.
1. On a clean surface remove all plastic
plugs from the NORAC expansion valve
block (V01).
2. Install the 6MBP (F03) into the A port
of the expansion block (Figure 2).
3. Install the 6MB 6MJ fitting (F04) into
the B port of the expansion block
(Figure 2).
Figure 2 - Third Station Expansion
Block Assembly
4. Remove the three 4MBP plugs from the
UC4+ 2 station valve block.
5. Coat the three o-rings in hydraulic oil
and install them into the expansion
block.
Make sure the o-rings are
properly seated.
Figure 3 - Expansion Valve O-Ring
Placement
6. Thread the 4.5” studs into the UC4+
block.
Figure 4 - Expansion Valve Stud
Insertion
7. Attach the expansion block to the
UC4+ block using the included spring
washers and nuts.
8. Tighten the nuts on the studs to 31 ft-
lbs Torque.
6
Figure 5 - Expansion Valve Final
Assembly
9. If the valve block is not already installed
on the sprayer, install it as outlined in
the UC4+ Spray Height Control kit
installation manual.
10. Attach hose H01 to port B on the
expansion block. Route the free end of
the hose (H01) to the Summers valve
block.
11. Remove the main lift hose from the
Summers valve block.
12. Place the 6FJXR 6MJT tee fitting (F02)
on the main lift fitting in the Summers
block.
13. Attach the Summers main lift hose and
hose H01 to the tee fitting.
You must ensure no hydraulic
components will interfere with
any sprayer parts or be pulled
tight at any time.
7
4 ELECTRICAL INSTALLATION
4.1 ROLL SENSOR INSTALLATION
1. Mount the roll sensor (E01) to the
included roll sensor bracket using the
machine screws and nylon lock nuts, as
illustrated in Figure 6.
The roll sensors must be
mounted tightly to the
brackets.
Figure 6 - Mounting the Roll Sensor to
the Roll Sensor Mounting Bracket
2. The roll sensor included in this kit is to
be mounted on the chassis as shown in
Figure 7. Ensure that the roll sensor
cabling is pointing to the right side of
the sprayer (when looking from the
rear).
3. Ensure that the roll sensor is relatively
level when the chassis is level.
4. Ensure that the chassis (Reference
Frame) roll sensor has the highest roll
sensor serial number (not including the
roll sensor with the temperature
probe).
Figure 7 – Chassis Roll Sensor
Mounting Location
5. Ensure the sensor is mounted
adequately and that the cable provides
enough slack.
Autres manuels pour UC4+
41
Table des matières
Autres manuels Norac Contrôleurs
Norac
Norac UC5 Topcon X30 Manuel utilisateur
Norac
Norac UC4+ Manuel utilisateur
Norac
Norac UC4 Plus Rogator 64 Series Manuel utilisateur
Norac
Norac UC4 Plus Rogator 1286C Manuel utilisateur
Norac
Norac UC4+ Manuel utilisateur
Norac
Norac UC4+ Manuel utilisateur
Norac
Norac UC4+ Manuel utilisateur
Norac
Norac UC4+ TA 1200 Manuel utilisateur
Norac
Norac UC5 Topcon X30 Manuel utilisateur
Norac
Norac UC5 Topcon X30 Manuel utilisateur
Norac
Norac UC5 Topcon X30 Manuel utilisateur
Norac
Norac UC4+ 1200/1600 Manuel utilisateur
Norac
Norac UC4+ SPRA-COUPE 7000 Series Manuel utilisateur
Norac
Norac UC5 Topcon X30 Manuel utilisateur
Norac
Norac NITRO Manuel utilisateur
Norac
Norac UC5 Topcon X30 Manuel utilisateur
Norac
Norac UC5 Topcon X30 Manuel utilisateur
Norac
Norac UC5 Topcon X30 Manuel utilisateur
Norac
Norac UC4+ Manuel utilisateur
Norac
Norac UC5 Topcon X30 Manuel utilisateur
