Norac UC4 Plus Rogator 64 Series Manuel utilisateur
UC4+ ROLL SENSOR UPGRADE KIT
Installation Manual
Spray Height Controller
Improving the competitiveness of Industry and Agriculture
throu
g
h Precision Measurement
Printed in Canada
Copyright 2005-08 by NORAC Systems International Inc.
Reorder P/N: 4473BC Rev D (UC4+ ROLL SENSOR UPGRADE KIT)
NOTICE
NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and without the requirement to
update products sold previously. Every effort has been made to ensure the accuracy of the information contained in this manual. The technical
information in this manual was reviewed at the time of approval for publication.
TABLE OF CONTENTS
1INTRODUCTION ................................................................................................................................................. 1
2GENERAL SYSTEM DESCRIPTION .................................................................................................................. 2
3PARTS LISTS......................................................................................................................................................... 3
4INSTALLATION PROCEDURE.......................................................................................................................... 4
4.1MAIN LIFT SENSOR ......................................................................................................................................... 4
4.2ROLL SENSOR INSTALLATION......................................................................................................................... 6
4.3ROLL SENSOR INSTALLATION (TRAPEZE STYLE BOOMS) .............................................................................. 7
4.3.1Boom Frame Roll Sensor Mounting 8
4.3.2Chassis Roll Sensor Mounting 9
4.4ROLL SENSOR INSTALLATION (CENTER PIVOT STYLE BOOMS) .................................................................. 10
4.4.1Boom Roll Sensor Mounting 11
4.4.2Chassis Roll Sensor Mounting 11
4.4.3Inverted Roll Sensor Mounting 12
4.5TEMPERATURE PROBE .................................................................................................................................. 13
4.6ELECTRICAL INSTALLATION ......................................................................................................................... 14
4.7COMPLETING THE INSTALLATION ................................................................................................................ 14
5ELECTRICAL REFERENCE – CABLE DRAWINGS....................................................................................... 15
5.1ITEM C02B: 44664 –CABLE UC4 CAN NODE DUAL.................................................................................. 15
1
1 INTRODUCTION
Congratulations on your purchase of the UC4+ Roll Sensor Upgrade Kit. Please take the time to read
this manual completely before attempting to install the system. A thorough understanding of this manual
will ensure that you receive the maximum benefit from the system.
YOUR INPUT CAN HELP MAKE US BETTER! If you find issues or have suggestions
regarding the parts list or the installation procedure, please don’t hesitate to contact.
IMPORTANT:
Please ensure that the software in your UC4+ panel has been updated to at least version 6.
The roll sensors included in this kit are designed to operate only with version 6 or newer in
the UC4+ panel.
2
2 GENERAL SYSTEM DESCRIPTION
Figure 1 depicts the general system layout of the UC4+ Spray Height Control system.
Figure 1 – System Components and General Location
NOTICE:
Every effort has been made to ensure the
accuracy of the information contained in this
manual. All parts supplied are selected specially
to fit the sprayer to facilitate a complete
installation. However, NORAC cannot
guarantee all parts fit as intended due to the
variations of the sprayer by the manufacturer.
Please read this manual in its entirety
before attempting installation.
3
3 PARTS LISTS
The parts that come with your UC4+ Roll Sensor Upgrade Kit are listed in Table 1.
Please ensure that all parts in your kit are present before proceeding with your installation.
Table 1 – UC4+ Roll Sensor Upgrade Kit
Item Part Number Name Quantity
C02B 44664 CABLE UC4 CAN NODE DUAL 1
E03 45000* UC4 PLUS ROLL SENSOR W TEMPERATURE PROBE VER. 2 1
E04 45001* UC4 PLUS ROLL SENSOR VER. 2 1
M01 446BC+MAN7 OPERATOR MANUAL UC4+ SPRAY HEIGHT CONTROL 1
M10 4473BC-INST MANUAL INSTALLATION UC4+ ROLL SENSOR UPGRADE KIT 1
* For systems purchased BEFORE October 1, 2011, the roll sensor part numbers are 44641 and 44642.
The parts that come with your UC4+ Roll Sensor Upgrade Kit are shown below in their
general installation configuration.
Figure 2 – UC4+ Roll Sensor Upgrade Kit
4
4 INSTALLATION PROCEDURE
4.1 MAIN LIFT SENSOR
With the UC4+ Roll Sensor Upgrade, the
aluminum target rod installed on the sprayer is
no longer required. Remove this rod from your
sprayer. The rod is found aligned under the
main lift sensor, which is usually mounted to the
left of the boom’s center section.
The main lift height sensor must also be moved.
Remove the main lift sensor bracket and follow
the steps below.
1. The bracket can be mounted to the lowest
frame member on the center section of the
sprayer. The bracket should be mounted so
the sensor mounting collar is in
approximately the center of the sprayer and
ahead of the boom (Figure 3 and Figure
5).
The sensor mounting collar must
not be behind the sprayer’s wheel.
The General Mounting Rules for
UC4+ Ultrasonic Sensors, listed on
the next page, must be followed.
Figure 3 – Main Lift Sensor Bracket Mounting Position
5
General mounting rules for UC4+
ultrasonic sensors:
a) In its lowest position, the sensor mouth
must be 9 inches or more from the ground.
b) The bottom of the sensor must be at least 9
inches in front of the spray nozzles.
c) The bottom of the sensor must be at least 9
inches above the spray nozzles.
d) Ensure that there are no obstructions within
a 12-inch diameter circle projected directly
below the center of the sensor.
e) The sensor should be approximately vertical
at normal operating heights.
Figure 4 - Sensor Mounting Guidlines
Figure 5 – Main Lift Sensor Mounted in
the Correct Location
A
B
B
D
C
Ultrasonic
Acoustic Cone
6
4.2 ROLL SENSOR INSTALLATION
Before installing the roll sensors you must
determine if your sprayer has a trapeze style or
center pivot style boom. For installation on a
trapeze style boom refer to Section 4.3. For
installation on a center pivot boom refer to
Section 4.4.
Figure 6 – Trapeze Style Boom
Figure 7 – Center Pivot Boom
Trapeze
Links
Center
Pivot
7
4.3 ROLL SENSOR INSTALLATION (TRAPEZE STYLE BOOMS)
Mount the roll sensors to the included roll
sensor brackets using the machine screws
and nylon lock nuts. (Figure 8)
The roll sensors must be mounted
tightly to the brackets.
Figure 8 – Mounting the Roll Sensor to
the Roll Sensor Mounting Bracket
When mounting the roll sensors, use the
following guidelines and refer to Figure 9.
a) The smaller the distance between Aand
Bin Figure 9, the better the
performance will be.
b) Ensure the roll sensors are sitting
relatively level when the sprayer chassis
and boom are level.
c) Both roll sensors must be mounted with
the circular AMP connector facing
towards the Right-Hand Wing (when
looking from the rear of the sprayer).
Figure 9 – General Roll Sensor Mounting Location on a Trapeze Style Boom
Connectors towards
Right-hand Wing
Autres manuels pour UC4 Plus Rogator 64 Series
5
Table des matières
Autres manuels Norac Contrôleurs
Norac
Norac UC4+ Mode d’emploi
Norac
Norac UC4+ Raptor Pro 1200 Manuel utilisateur
Norac
Norac UC4+ Manuel utilisateur
Norac
Norac UC4+ Manuel utilisateur
Norac
Norac UC4 Plus Rogator 64 Series Manuel utilisateur
Norac
Norac UC4+ Manuel utilisateur
Norac
Norac UC5 Topcon X30 Manuel utilisateur
Norac
Norac UC4.5 Manuel utilisateur
Norac
Norac UC5 Topcon X30 Manuel utilisateur
Norac
Norac UC5 Topcon X30 Manuel utilisateur
Norac
Norac Case AFS Pro 600 Manuel utilisateur
Norac
Norac UC5-BC-JD11 Manuel utilisateur
Norac
Norac UC4+ Manuel utilisateur
Norac
Norac UC4+ Manuel utilisateur
Norac
Norac UC4 Total Control Manuel utilisateur
Norac
Norac UC4 Plus Rogator 1286C Manuel utilisateur
Norac
Norac UC5 Topcon X30 Manuel utilisateur
Norac
Norac UC4+ Manuel utilisateur
Norac
Norac UC4+ Manuel utilisateur
Norac
Norac UC4 Plus Rogator 64 Series Manuel utilisateur
