Norac UC5 Topcon X30 Manuel utilisateur

ohn Deere GS2 2600, 1800 and GS3

2630

JD 4630 Display Kit

Installation Manual

GS2-SP02

Printed in Canada

Reorder P/N: 54VT-GS2-SP02-INST Rev D (John Deere GS2 2600, 1800 and GS3 2630 JD

4630 Display Kit)

NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and

without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information

contained in this manual. The technical information in this manual was reviewed at the time of approval for publication.

Contents

1INTRODUCTION .............................................................................................2

1.1List of Parts................................................................................................................................................................. 2

2TECHNICAL SPECIFICATIONS ....................................................................3

3INSTALLATION ...............................................................................................4

3.1CANbus Interface Installation................................................................................................................................. 4

3.2Switch Box Installation ............................................................................................................................................. 5

4CABLE DRAWINGS.........................................................................................6

4.1Item C25: 44602-01 – Switch Remote Hand Control ..................................................................................... 6

4.2Item C26: 43240-26 – Cable UC5 Switch Box.................................................................................................. 7

4.3Item C40: 43260-08 – Cable UC5 CANbus 4 Pin DT..................................................................................... 8

4.4Item C41: 43210-01 - Cable UC5 Network 18 AWG - 1M............................................................................ 9

1Introduction

The John Deere GS2 2600, 1800 and GS3 2630 Display Kit Manual is intended to be used in

conjunction with the UC5 Spray Height Control Installation Manual. This manual provides

instructions to interface the UC5 Control Module to the John Deere GS2 2600, 1800 and GS3

2630 Display. For installation of the rest of the UC5 Spray Height Control System please refer

to the sprayer specific manual provided with the kit.

1.1 List of Parts

Item Part Number Name Quantity

C25 44602-01 BOX SWITCH UC4 REMOTE HAND CONTROL VER.1 RMR 1

C26 43240-26 CABLE UC5 SWITCH BOX 1

C40 43260-08 CABLE UC5 INTERFACE CAN BUS 4 PIN DT 1

C41 43210-01 CABLE UC5 NETWORK 18 AWG 1M 1

E12 43764 UC5 NETWORK COUPLER 2-WAY 1

M01 UC5-BC-MANUAL-ECHO-VT MANUAL UC5 OPERATORS - ECHO/VT 1

M04 54VT-GS2-SP02-INST MANUAL UC5 DISPLAY KIT JOHN DEERE GS2 2600, 1800 and GS3 2630 (JD 4630) 1

2Technical Specifications

CAN ICES-3(A)/NMB-3(A)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interference at their

own expense.

This Class A digital apparatus complies with Canadian ICES-003.

Pursuant to EMC Directive – Article 9, this product is not intended for residential use.

Table 1: System Specifications

Supply Voltage (rated)

12VDC

Supply Current (rated)

Hydraulic Pressure (maximum)

3300 psi

Baud Rate 250 kbps

Clock Frequency (maximum)

96 MHz

Solenoid Valve PWM Frequency

300 Hz

Ultrasonic Sensor Transmit Frequency

50 kHz

Operating Temperature Range

0°C to 80°C

3Installation

3.1 CANbus Interface Installation

1. Securely mount the control module (E01) inside the sprayer cab.

2. Tee the CANbus interface cable (C40) in to the John Deere CANbus. The John Deere

CANbus connection can be found in the right hand armrest. The connector is a 4 pin

Deutsch plug labeled “CAN 2”.

3. Connect the 6 pin Deutsch plug on cable C40 to the 2-way coupler (E12). Connect cable

C41 between the 2-way coupler (E12) and the end of the control module with only one

Deutsch connector. C41 and E12 may not be required.

Figure 1: CANbus Interface Installation

3.2 Switch Box Installation

1. This step of the installation assumes that the input module and all required cables are

installed.

2. Disconnect cable C20 (Thru 2 connector) from the Input Module (E03). Remove the wedge

from the face of the 12 pin Deutsch plug. The wedge is removed by inserting a small flat

implement underneath the wedge and lifting it up.

3. Insert the Roll CW pin from C26 into position 3 of the 12 pin plug on C20. Insert the Roll

CCW pin from C26 into position 4 of the 12 pin plug on C20. Insert the wedge back into

the plug. Connect C20 to the Thru 2 connector on the Input Module.

4. Connect the 12 pin Deutsch plug on C26 to the OEM 3 connector on the input module.

Route the other end of the cable to the hitch of the sprayer (pull type) or to the cab (self

propelled).

5. Attach the switch box (C25) inside the cab and connect it to cable C26. An extra label is

provided with the switch box if you prefer to remove the switches from the housing and

mount them in the existing sprayer switch panel.

* Some sprayer types may not use all the switch functions.

Figure 2: Switch Box Installation

4Cable Drawings

4.1 Item C25: 44602-01 – Switch Remote Hand Control

4.2 Item C26: 43240-26 – Cable UC5 Switch Box

4.3 Item C40: 43260-08 – Cable UC5 CANbus 4 Pin DT

Autres manuels pour UC5 Topcon X30

Table des matières

Autres manuels Norac Contrôleurs

Norac

Norac Case AFS Pro 600 Manuel utilisateur

Norac

Norac UC5 Topcon X30 Manuel utilisateur

Norac

Norac UC5 Topcon X30 Manuel utilisateur

Norac

Norac UC5 Topcon X30 Manuel utilisateur

Norac

Norac UC4+ Hardi OEM Manuel utilisateur

Norac

Norac UC5 Topcon X30 Manuel utilisateur

Norac

Norac UC4+ Apache 1010 2005+ Manuel utilisateur

Norac

Norac UC4 Plus Rogator 64 Series Manuel utilisateur

Norac

Norac UC4+ Roll Control Manuel utilisateur

Norac

Norac UC4+ Manuel utilisateur

Norac

Norac UC4+ Manuel utilisateur

Norac

Norac UC5 Topcon X30 Manuel utilisateur

Norac

Norac UC5 Topcon X30 Manuel utilisateur

Norac

Norac UC4+ Manuel utilisateur

Norac

Norac UC5 Topcon X30 Manuel utilisateur

Norac

Norac UC4+ Mode d’emploi

Norac

Norac UC4+ Manuel utilisateur

Norac

Norac UC4 Plus Rogator 74 Series Manuel utilisateur

Norac

Norac UC4+ Manuel utilisateur

Norac

Norac UC5 Topcon X30 Manuel utilisateur

Norac

Norac UC4+ Manuel utilisateur

Norac

Norac UC4 Plus Rogator 64 Series Manuel utilisateur

Norac

Norac UC5 Topcon X30 Manuel utilisateur

Norac

Norac UC5 Topcon X30 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur