Norac UC5 Topcon X30 Manuel utilisateur
Trimble FMX
Display Kit
In
sta
ll
at
i
o
n
M
a
n
ua
l
54VT-TB-FMX
Printed in Canada
Copyright 2015 by NORAC Systems International Inc.
Reorder P/N: 54VT-TB-FMX-INST Rev B (Trimble FMX Display Kit)
NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and
without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information
contained in this manual. The technical information in this manual was reviewed at the time of approval for publication.
1
Contents
1INTRODUCTION ...................................................................................................... 2
1.1List of Parts..........................................................................................................................................................................2
1.2Alternate Cabling................................................................................................................................................................2
2INSTALLATION ........................................................................................................ 3
2.1Self-Propelled.......................................................................................................................................................................3
2.2Pull Type...............................................................................................................................................................................4
2.3Switch Box Installation ......................................................................................................................................................7
3CABLE DRAWINGS.................................................................................................. 8
3.1ITEM C25: 44602-01 – Switch Remote Hand Control .............................................................................................8
3.2ITEM C26: 43240-26 – Cable UC5 Switch Box..........................................................................................................9
3.3ITEM C40: 43260-30 – Cable UC5 Interface DTM 4 Pin 12in Stub.................................................................... 10
3.4ITEM C41: 43220-03 - Cable UC5 Network 14 AWG - 3M ............................................................................... 11
2
1Introduction
The Trimble FMX Display Kit Manual is intended to be used in conjunction with the UC5 Spray
Height Control Installation Manual. This manual provides instructions to interface the UC5
Control Module to the Trimble FMX Display. For installation of the rest of the UC5 Spray
Height Control System please refer to the sprayer specific manual provided with the kit.
1.1 List of Parts
Item Part Number Name Quantity
C25 44602-01 BOX SWITCH UC4 REMOTE HAND CONTROL VER.1 RMR 1
C26 43240-26 CABLE UC5 INTERFACE SWITCH BOX 1
C40 43260-30 CABLE UC5 INTERFACE DTM 4 PIN 12 IN STUB 1
C41 43220-03 CABLE UC5 NETWORK 14 AWG 3M 1
E12 43764 UC5 NETWORK COUPLER 2-WAY 1
M01 UC5-BC-MANUAL-ECHO-VT MANUAL UC5 OPERATORS - ECHO/VT 1
M04 54VT-TB-FMX-INST MANUAL UC5 DISPLAY KIT TRIMBLE FMX 1
Trimble FMX version must be 8.0 or higher.
Trimble part numbers are subject to change without notice.
1.2 Alternate Cabling
If the control module is mounted on the sprayer of a pull-type sprayer (non-ISOBUS ready
tractor) (Section 2.2.3), cable C42 is required to replace C40. This cable can be ordered from
NORAC.
Item Part Number Name Quantity
C42 43260-29 CABLE UC5 INTERFACE DT 4 PIN 12 IN STUB 1
3
2Installation
The following instructions are for installation on a self-propelled sprayer (Section 2.1) or pull
type sprayer (Section 2.2).
2.1 Self-Propelled
1. Securely mount the control module (E01) inside the sprayer cab.
2. Tee the CANbus interface cable (C40) between the Trimble cable 75834 and the ISOBUS
trunk cable that runs to the back of the sprayer.
3. Connect the 6 pin Deutsch plug on cable C40 to the end of the control module with only
one Deutsch connector.
4. Connect cable C01 to the other CANbus connector and route the cable towards the rear
of the sprayer.
Note: Not all cables listed in the List of Parts (Section 1.1) are used for this type of installation.
Figure 1: Self Propelled Sprayer Installation
4
2.2 Pull Type
2.2.1 Control Module on Tractor (Non-ISOBUS Ready Tractor)
1. Securely mount the control module (E01) inside the tractor cab.
2. Tee the CANbus interface cable (C40) between Trimble cable 75834 and Trimble cable
77368.
3. Connect the 6 pin Deutsch plug on cable C40 to the end of the control module with only
one Deutsch connector.
4. Connect cable C41 to the CANbus connector and route the cable to the hitch of the
tractor. Connect the two-way coupler (E12) to the end of cable C41.
5. Connect cable C01 to the coupler (E12) and route towards the rear of the sprayer. The
two-way coupler (E12) will provide the hitch disconnect.
Figure 2: Pull Type with Control Module on Non-ISOBUS Ready Tractor Installation
5
2.2.2 Control Module on Tractor (ISOBUS Ready Tractor)
1. Securely mount the control module (E01) inside the tractor cab.
2. Tee the CANbus interface cable (C40) between Trimble cable 75407 and Trimble cable
92752.
3. Connect the 6 pin Deutsch plug on cable C40 to the end of the control module with only
one Deutsch connector.
4. Connect cable C41 to the CANbus connector and route the cable to the hitch of the
tractor. Connect the two-way coupler (E12) to the end of cable C41.
5. Connect cable C01 to the coupler (E12) and route towards the rear of the sprayer. The
two-way coupler (E12) will provide the hitch disconnect.
Figure 3: Pull Type with Control Module on ISOBUS Ready Tractor Installation
6
2.2.3 Control Module on Sprayer (Non-ISOBUS Ready Tractor)
Cable C42 is required for this type of installation. Please order the following cable from
NORAC:
Item Part Number Name Quantity
C42 43260-29 CABLE UC5 INTERFACE DT 4 PIN 12 IN STUB 1
1. Securely mount the control module (E01) on the sprayer near the CANbus connection.
2. Tee the CANbus interface cable (C42) between Trimble cable 77368 and the IBRC
connector.
3. Connect the 6 pin Deutsch plug on cable C42 to the end of the control module with only
one Deutsch connector.
4. Connect cable C01 to the other CANbus connector and route the cable towards the rear
of the sprayer.
Note: Not all cables listed in the List of Parts (Section 1.1) are used for this type of installation.
Figure 4: Pull Type with Control Module on Sprayer (Non-ISOBUS Ready Tractor) Installation
7
2.3 Switch Box Installation
The switch box is an optional component to make the operation of the UC5 easier. An extra
label is provided if the operator would like to remove the switches from the box and mount
them in another location.
1. Disconnect cable C20 (Thru 2 connector) from the Input Module (E03). Remove the wedge
from the face of the 12 pin Deutsch plug.
2. Insert the Roll CW pin from C26 into position 3 of the 12 pin plug on C20. Insert the Roll
CCW pin from C26 into position 4 of the 12 pin plug on C20. Insert the wedge back into
the plug. Connect C20 to the Thru 2 connector on the Input Module.
3. Connect the 12 pin Deutsch plug on C26 to the OEM 3 connector on the input module.
Route the other end of the cable to the hitch of the sprayer (pull type) or to the cab (self
propelled).
4. Attach the switch box (C25) inside the cab and connect it to cable C26. An extra label is
provided with the switch box if you prefer to remove the switches from the housing and
mount them in the existing sprayer switch panel.
* Some sprayer types may not use all the switch functions.
Figure 5: Switch Box Installation
8
3Cable Drawings
3.1 ITEM C25: 44602-01 – Switch Remote Hand Control
Autres manuels pour UC5 Topcon X30
55
Table des matières
Autres manuels Norac Système de contrôle
Norac
Norac RG11 Manuel utilisateur
Norac
Norac UC4+ Manuel utilisateur
Norac
Norac UC4+ Manuel utilisateur
Norac
Norac UC5 HD12 Manuel utilisateur
Norac
Norac UC5 Topcon X30 Manuel utilisateur
Norac
Norac UC4+ Manuel utilisateur
Norac
Norac PULSE UC5 Manuel d'utilisation et d'entretien
Norac
Norac UC5 Topcon X30 Manuel utilisateur
Norac
Norac UC5 Topcon X30 Manuel utilisateur
Norac
Norac SPRA-COUPE 7000 Series Manuel utilisateur
Norac
Norac UC4.5 Manuel utilisateur
Norac
Norac UC4+ Manuel utilisateur
Norac
Norac UC5 MAX Manuel utilisateur
Norac
Norac UC4.5 Manuel utilisateur
Norac
Norac UC4.5 Manuel utilisateur
Norac
Norac John Deere 4720 Manuel utilisateur
Norac
Norac UC4.5 Manuel utilisateur
Norac
Norac UC4+ Manuel utilisateur
Norac
Norac UC4+ Manuel utilisateur
Norac
Norac UC7 Manuel utilisateur
