Norac UC4.5 Manuel utilisateur

ohn Deere

(30 Series Main Lift Option)

Installation Manual

Printed in Canada

Reorder P/N: UC4.5-JD9-INST Rev A (John Deere 30 Series Main Lift Option)

NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and

without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information

contained in this manual. The technical information in this manual was reviewed at the time of approval for publication.

Contents

1Introduction................................................................................................................ 1

2Kit Parts ...................................................................................................................... 2

3Ultrasonic Sensor Installation .................................................................................. 5

4Hydraulic Installation ................................................................................................ 8

5Electrical Installation ............................................................................................... 10

6Software Setup......................................................................................................... 11

7Cable Drawings ........................................................................................................ 12

1Introduction

Congratulations on your purchase of the NORAC UC4.5 Spray Height Control System. This

system is manufactured with top quality components and is engineered using the latest

technology to provide operating reliability unmatched for years to come.

When properly used the system can provide protection from sprayer boom damage, improve

sprayer efficiency, and ensure chemicals are applied correctly.

Please take the time to read this manual completely before attempting to install the system. A

thorough understanding of this manual will ensure that you receive the maximum benefit from

the system.

Your input can help make us better! If you find issues or have suggestions regarding the parts

list or the installation procedure, please don’t hesitate to contact us.

Every effort has been made to ensure the accuracy of the information contained in

this manual. All parts supplied are selected to specially fit the sprayer to facilitate

a complete installation. However, NORAC cannot guarantee all parts fit as

intended due to the variations of the sprayer by the manufacturer.

Please read this manual in its entirety before attempting installation.

2Kit Parts

2.1 Hydraulic Plumbing

Figure 1: JD9 Hydraulic Plumbing

2.2 List of Parts

The following tables list the John Deere 30 Series main lift kit (JD9) specific parts of the

NORAC UC4.5 system. This kit is to be used when installing the proportional main lift option

with existing John Deere installations.

Item Part Number Name Quantity

B21 44973 SENSOR MOUNTING BRACKET LOW PROFILE 16 GA LARGE FLANGE 1

C07 43220-01 CABLE UC5 NETWORK 14 AWG 1M 1

C17 44658-45D CABLE UC4 VALVE MAIN DT 1

E05 43750 UC5 ULTRASONIC SENSOR 1

E12 43764 UC5 NETWORK COUPLER 2-WAY 1

H03 44863-23 HOSE ASSEMBLY 122R2-06 32IN L 6FORX 6FORX 1

H10 44865-37 HYDRAULICS FITTING KIT - JD9 1

M01 UC4.5-JD9-INST MANUAL INSTALLATION UC4.5 JOHN DEERE 30 SERIES PROP MAIN LIFT OPTION 1

V01 44962D VALVE ASSEMBLY EXPANSION DPOC PROP DT 4 BOLT 1

2.3 Hydraulic Fitting Kit Details (P/N: 44865-37)

Item Part Number Name Quantity Picture

F03 104586 TEE ADAPTER - 6FORXR 6MORT 1

F05 44917 MALE ADAPTER - 6MB 6MOR 1

*F08 44926 ORIFICE INSERT 3/64" 1

F09 104369 PLUG - 6MBP 1

6 M B - 6 M OR X 90

SIZE IN

1/16TH'S

GENDER: MALE

OR FEMALE

90° ANGLE

SWIVEL

TYPE

GENDER

SIZE

TYPE:

B - ORB

J - JIC

OR - FLAT

FACE

P - PIPE

Fitting Name

Example:

* Orifice F08 is not required when installing on a John Deere 4930.

The use of dielectric grease is not recommended on any NORAC electrical

connections.

To ensure all stainless steel hardware does not gall or seize apply a light coating of

the supplied Permatex Anti-seize grease to all threaded parts upon installation.

Permatex Anti-seize lubricant is preferred, but other similar anti-seize products

may be used.

3Ultrasonic Sensor Installation

3.1 Ultrasonic Sensor Mounting Guidelines

The following guidelines will ensure optimal sensor performance and prevent

sensor measurement error. These rules should be followed for both the wing

sensors and the main lift (middle) sensor.

1. In its lowest position, the sensor must be 9 inches (23 cm) or more from the ground.

2. Ensure that there are no obstructions within a 12-inch diameter circle projected directly

below the center of the sensor.

3. The sensor should be approximately vertical at normal operating heights.

Figure 2: Sensor Mounting Guidelines

3.2 Low Profile Bracket Mounting Guidelines

1. Minimize the distance between the bolts to prevent bending the bracket and prevent the

bracket from loosening over time.

2. Ensure the bracket is mounted tight against the bottom of the boom, minimizing the

distance between the boom structure and the angled flange.

Figure 3: Bracket Mounting Guidelines

A problem can arise if a sensor is not mounted correctly. It is possible for the

sensor to read off of the boom instead of the ground. This may only become

apparent once the control system is switched from soil to crop mode.

Also be careful that the sensor bracket does not collide with any other part of the

boom when the boom is folded to transport position. If possible, mount the sensor

brackets while the booms are folded to ensure they will not cause interference.

3.3 Main Lift Sensor Installation

1. The main lift mounting bracket (B21) is the bracket with the longer mounting flange.

2. There are a variety of ways to mount the main lift bracket on most sprayers. The bracket

should position the sensor approximately in the center of the sprayer, forward of the

boom. An example of this mounting is illustrated in Figure 5.

Figure 4: Bracket Mounting Example

3. Mount the ultrasonic sensor to the main lift bracket. Run the sensor cable through hole

and behind the bracket.

Figure 5: Example Mounting of the Main Lift Bracket

Avoid mounting the main lift sensor over or near a wheel-track. Measurements

from the wheel-track do not provide an accurate crop height and will cause

measurement and control error.

Ensure the bracket does not collide with any other part of the sprayer throughout

the full range of main lift motion.

Front

Autres manuels pour UC4.5

Table des matières

Autres manuels Norac Système de contrôle

Norac

Norac UC4+ Manuel utilisateur

Norac

Norac UC5 Topcon X30 Manuel utilisateur

Norac

Norac SPRA-COUPE 7000 Series Manuel utilisateur

Norac

Norac UC4 Total Control Manuel utilisateur

Norac

Norac UC5 HD12 Manuel utilisateur

Norac

Norac UC4.5 Manuel utilisateur

Norac

Norac PULSE UC5 Manuel d'utilisation et d'entretien

Norac

Norac UC5 CAN BUS Case IH 20 Series Manuel utilisateur

Norac

Norac UC4+ Manuel utilisateur

Norac

Norac UC5 Topcon X30 Guide de démarrage rapide

Norac

Norac UC4 Total Control Manuel utilisateur

Norac

Norac UC5 Topcon X30 Manuel utilisateur

Norac

Norac UC4.5 Manuel utilisateur

Norac

Norac UC5 Topcon X30 Manuel utilisateur

Norac

Norac RG11 Manuel utilisateur

Norac

Norac Active Roll Control UC5 Series Manuel utilisateur

Norac

Norac UC4 Plus Rogator 64 Series Manuel utilisateur

Norac

Norac UC4.5 Manuel utilisateur

Norac

Norac UC4+ Manuel utilisateur

Norac

Norac UC4+ Manuel utilisateur

Norac

Norac UC4.5 Manuel utilisateur

Norac

Norac UC7 Manuel utilisateur

Norac

Norac UC4 Total Control Manuel utilisateur

Norac

Norac UC4+ Manuel utilisateur

Manuels Système de contrôle populaires d'autres marques

Pentair Pool Products

Pentair Pool Products Compool Manuel utilisateur

ComfortNET

ComfortNET CTK04 Manuel utilisateur

Fireye

Fireye InSight II 95DSS3 Manuel utilisateur

CAME

CAME G3000 Manuel utilisateur

Idemia

Idemia MorphoAccess VP MD Manuel utilisateur

Axis

Axis P1445-LE-3 Manuel utilisateur

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuel utilisateur

CNC-Step

CNC-Step High-Z T-Series Manuel utilisateur

Doosan

Doosan DVF Series Manuel utilisateur

Honeywell

Honeywell KAP 140 Manuel utilisateur

Honeywell

Honeywell vk41 series Manuel utilisateur

AirBench

AirBench FPW Guide d'installation

Cypress

Cypress HHR-3160 Manuel utilisateur

CAME

CAME GLT40AOS Manuel utilisateur

Zonex

Zonex GEN II -VVT Guide de l'utilisateur

Altronics

Altronics K 9650 Manuel utilisateur

micro-trak

micro-trak RoadMaster Manuel utilisateur

micro-trak

micro-trak Calc-An-Acre II Manuel utilisateur