NCR 7454 Manuel utilisateur

NCR 7454 Retail Terminal

Release 2.1

Hardware User’s Guide

18004

NCR

B005-0000-1256

Issue G

The products described in this book are licensed products of NCR Corporation.

NCR is a registered trademark of NCR Corporation.

Microtouch is a registered trademark of 3M.

Sound Blaster is a registered trademark of Creative Technology Ltd. in the United States and/or other

countries.

Intel, Pentium, and Celeron are registered trademarks of Intel Corporation.

Microsoft, Windows, Windows NT, and MS-DOS are either trademarks or registered trademarks of

Microsoft Corporation in the United States and/or other countries.

DiskOnChip is a trademark or registered trademark of M-Systems in the United States.

Novell and Netware are either registered trademarks or trademarks of Novell, Inc. in the United States and

other countries.

UNIX is a registered trademark of The Open Group in the United States and other countries.

Ghost is a registered trademark of Symantec Corporation in the United States and other countries.

It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software,

and firmware become available. NCR, therefore, reserves the right to change specifications without prior

notice.

All features, functions, and operations described herein may not be marketed by NCR in all parts of the

world. In some instances, photographs are of equipment prototypes. Therefore, before using this document,

consult with your NCR representative or NCR office for information that is applicable and current.

To maintain the quality of our publications, we need your comments on the accuracy, clarity, organization,

and value of this book.

Address correspondence to:

Manager, Information Products

NCR Corporation

2651 Satellite Blvd.

Duluth, GA 30096

By NCR Corporation

Dayton, Ohio U.S.A.

Preface

Audience

This book is written for hardware installer/service personnel, system

integrators, and field engineers.

Notice: This document is NCR proprietary information and is not to

be disclosed or reproduced without consent.

Safety Warnings

Fuse Replacement

Caution: For continued protection against risk of fire, replace only

with the same type and ratings of fuse.

Attention: Pour prévenir et vous protéger contre un risque de feu,

remplacer la fusible avec une autre fusible de même type, seulement.

Power Supply Cord Used as Disconnect Means

Caution: The power supply cord is used as the main disconnect

device. Ensure that the socket outlet is located/installed near the

equipment and is easily accessible.

Attention: Le cordon d'alimentation est utilisé comme interrupteur

général. La prise de courant doit être située ou installée å proximité du

matériel et être facile d'accés.

Warning: DO NOT connect or disconnect a printer, keyboard, or

any other terminal-powered peripheral while the terminal is

powered on. Doing so may result in peripheral or system damage.

Warning: The NCR 7454 must be mounted securely to prevent a

hazard. It must be installed in accordance with local building codes.

The post or wall on which the unit is mounted should be able to

withstand four times the weight of the unit, which is approximately

20 lbs. (9 kg).

Lithium Battery Warning

Caution: Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type as recommended by the

manufacturer. Discard used batteries according to the manufacturer’s

instructions.

Attention: Il y a danger d'explosion s'il y a remplacement incorrect de

la batterie. Remplacer uniquement avec une batterie du même type ou

d'un type recommandé par le constructeur. Mettre au rébut les

batteries usagées conformément aux instructions du fabricant.

Peripheral Usage

This terminal should only be used with peripheral devices that are

certified by the appropriate safety agency for the country of installation

(UL, CSA, TUV, VDE) or those which are recommended by NCR

Corporation.

Environmental Consciousness

NCR is demonstrating its concern for the environment by designing an

intelligent power management system into this terminal that operates

efficiently whether the system is in a stand-alone or network

environment.

iii

References

•NCR 7454 Retail Terminal Hardware Service Guide

(B005-0000-1342)

•NCR 7454 Retail Terminal Site Preparation Guide

(B005-0000-1257)

•NCR 7454 Retail Terminal Software User’s Guide

(B005-0000-1259)

•NCR 7401/7454 Retail Terminal Parts Identification Manual

(B005-0000-1072)

•NCR 7401/7454 Retail Terminal Diagnostics and Troubleshooting Guide

(B005-0000-1101)

•NCR FitClient Software User’s Guide

(B005-0000-1235)

Table of Contents

Chapter 1: Product Overview

Introduction......................................................................1-1

Serial Number/Model Number Label..........................1-2

Hardware Modules .........................................................1-3

Base Unit ....................................................................1-3

Hardware Options ....................................................1-4

Terminal Components not Supported...............1-6

System Configuration Diagram.....................................1-7

Hardware Module Descriptions....................................1-8

Processor Board.........................................................1-8

Processor/Chip Set...............................................1-8

Video Subsystem ..................................................1-8

Ethernet 10/100Base-T LAN

Communications...................................................1-9

Wireless LAN Communications.......................1-10

Universal Serial Bus ...........................................1-11

Serial Ports...........................................................1-12

Hardware Monitor .............................................1-13

PCI Expansion Header.......................................1-13

IDE Header..........................................................1-13

Audio....................................................................1-13

Magnetic Stripe Reader......................................1-14

Touch Screen Controller ....................................1-14

Processor Board Connectors .............................1-14

Flash Disk ............................................................1-15

NCR Retail Specific Hardware .........................1-15

Board BIOS ..........................................................1-18

BIOS Upgrades....................................................1-19

Operator Display.....................................................1-21

LCD Adapter Board ...........................................1-21

LCD Backlight Inverter Module .......................1-22

Touch Screen .......................................................1-22

NCR 7454 Integrated Customer Display .............1-23

NCR 5973 International VFD Customer Display1-24

Table Top Mount ................................................1-24

16" High Post Mount..........................................1-24

Features...........................................................................1-25

Magnetic Stripe Reader..........................................1-25

Printer Options........................................................1-26

7158 Printer..........................................................1-26

7166 Printer..........................................................1-27

7194 Printer..........................................................1-27

7196 Printer..........................................................1-28

2214 Printer..........................................................1-28

Other Integrated Devices and Indicators ............1-29

Hard Disk Drive..................................................1-29

Reset Switch.........................................................1-29

Internal Speaker..................................................1-29

POS Connector Board ........................................1-30

Motion Sensor .....................................................1-30

Power/Status LED .............................................1-31

Power OK LED....................................................1-31

LAN Status LEDs................................................1-31

Power Supply......................................................1-32

Integrated Speaker Module (Optional) ...........1-32

USB RS-232 Port Server......................................1-33

Additional Pentium III Connectors..................1-34

vii

Chapter 2: Hardware Installation

Introduction......................................................................2-1

Installation Summary ...............................................2-1

Installation Restrictions ..................................................2-2

Connecting the Cables ....................................................2-3

Accessing the Cable Connectors.............................2-3

Routing the Cables....................................................2-4

Identifying the Cable Connectors...........................2-5

Installing Peripherals ......................................................2-6

Installing a Transaction Printer...............................2-6

7158 Printer............................................................2-6

7166 Printer............................................................2-7

7194 Printer............................................................2-8

7196 Printer............................................................2-9

2214 Printer..........................................................2-10

Installing a Remote Customer Display ................2-11

7454-K453 Remote Customer Display .............2-11

5972-1100 Remote Customer Display ..............2-13

5973 International VFD Customer Display.....2-15

Installing a High-Post Integrated Customer

Display......................................................................2-17

Installing a Cash Drawer .......................................2-23

Installing a Second Cash Drawer .....................2-24

Mounting the 7454.........................................................2-25

Wall Mounting a Tilt Mount .................................2-26

Finalizing the Installation.............................................2-27

Completing the OS Installation (WinNT) .......2-27

Completing the OS Installation (Win98) .........2-27

Completing the OS Installation (Win95) .........2-28

Completing the OS Installation (DOS) ............2-28

Setting Auto-Logon (WinNT Terminal).....................2-29

viii

Installing a Serial Mouse ..............................................2-34

Guidelines for Calibrating the Touch Screen ............2-35

Calibration Procedure ............................................2-35

Summary..................................................................2-37

Out-of-Box Failures .......................................................2-37

Chapter 3: Setup

Introduction......................................................................3-1

Entering Setup Without a Keyboard......................3-1

Entering Setup Using a Keyboard ..........................3-2

How to Select Menu Options ..................................3-2

Restoring Factory Settings .......................................3-3

Setup Menus (Pentium)..................................................3-4

Main Menu.................................................................3-4

System Time and Date .........................................3-4

Legacy Diskette.....................................................3-4

Primary Master .....................................................3-5

Memory Cache......................................................3-6

Advanced Menu........................................................3-8

I/O Device Configuration ...................................3-8

Multiple ROM Menu..........................................3-12

Plug and Play O/S..............................................3-13

Reset Configuration Data ..................................3-14

PS/2 Mouse .........................................................3-14

Large Disk Access...............................................3-15

Secured Setup Configurations ..........................3-15

PCI Configuration ..............................................3-16

Security Menu Options ..........................................3-19

Set Supervisor/User Password ........................3-19

Password on Boot ...............................................3-20

Power Menu Options .............................................3-21

Autres manuels pour 7454

Table des matières

Autres manuels NCR Terminal tactile

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur

Prestel

Prestel VCS-G2PRO Manuel utilisateur