NCR 7460 Manuel utilisateur

NCR 7460 Retail Terminal

Release 1.2

Hardware User’s Guide

B005-0000-1280

Issue D

The products described in this book are licensed products of NCR Corporation.

NCR is a registered trademark of NCR Corporation.

Pentium is a registered trademark of Intel Corporation.

It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software,

and firmware become available. NCR, therefore, reserves the right to change specifications without prior

notice.

All features, functions, and operations described herein may not be marketed by NCR in all parts of the

world. In some instances, photographs are of equipment prototypes. Therefore, before using this document,

consult with your NCR representative or NCR office for information that is applicable and current.

To maintain the quality of our publications, we need your comments on the accuracy, clarity, organization,

and value of this book.

Address correspondence to:

Manager, Information Products

NCR Corporation

2651 Satellite Blvd.

Duluth, GA 30096

By NCR Corporation

Dayton, Ohio U.S.A.

Preface

Audience

This book is written for hardware installer/service personnel, system

integrators, and field engineers.

Safety Warnings

Warning: No user serviceable parts. Servicing should only be

performed by a qualified service technician.

Caution: For continued protection against risk of fire, replace only

with the same type and ratings of fuse.

Attention: Pour prévenir et vous protéger contre un risque de feu,

remplacer la fusible avec une autre fusible de même type, seulement.

Power Supply Cord Used as Disconnect Means

Caution: The power supply cord is used as the main disconnect

device. Ensure that the socket outlet is located/installed near the

equipment and is easily accessible.

Attention: Le cordon d'alimentation est utilisé comme interrupteur

général. La prise de courant doit être située ou installée å proximité du

matériel et être facile d'accés.

Warning: DO NOT connect or disconnect a printer, keyboard, or

any other terminal-powered peripheral while the terminal is

powered on. Doing so may result in peripheral or system damage.

Fuse Replacement

Caution: Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type as recommended by the

manufacturer. Discard used batteries according to the manufacturer’s

instructions. Switzerland (only) refer to Anex 4.10 of SR 814.013.

Attention: Il y a danger d'explosion s'il y a remplacement incorrect de

la batterie. Remplacer uniquement avec une batterie du même type ou

d'un type recommandé par le constructeur. Mettre au rébut les

batteries usagées conformément aux instructions du fabricant.

Recycling

Contact local NCR representative for information regarding proper

disposal and recycling of equipment.

Attention: Pour prévenir et vous protéger contre un risque de feu,

remplacer la fusible avec une autre fusible de même type, seulement.

Peripheral Usage

This terminal should only be used with peripheral devices that are

certified by the appropriate safety agency for the country of installation

(UL, CSA, TUV, VDE) or those which are recommended by NCR

Corporation.

Environmental Consciousness

NCR is demonstrating its concern for the environment by designing an

intelligent power management system into this terminal that operates

efficiently whether the system is in a stand-alone or network

environment.

References

•NCR 7460 Retail Terminal Site Preparation Guide

(B005-0000-1281)

•NCR FitClient Software User’s Guide

(B005-0000-1235)

•NCR 7460 Retail Terminal Parts Identification Manual

(B005-0000-1282)

•NCR 7460 Retail Terminal Service Guide

(B005-0000-1338)

iii

Table of Contents

Chapter 1: Product Overview

Introduction......................................................................1-1

Serial Number Labels......................................................1-2

Hardware Modules .........................................................1-3

Base Unit ....................................................................1-3

Hardware Options ....................................................1-4

Terminal Components not Supported...............1-5

System Configuration Diagram.....................................1-6

Hardware Module Descriptions....................................1-7

Processor Board.........................................................1-7

Processor/Chip Set...............................................1-7

Video Subsystem ..................................................1-7

Ethernet 10/100Base-T LAN

Communications...................................................1-8

Universal Serial Bus .............................................1-9

Serial Ports.............................................................1-9

Hardware Monitor .............................................1-10

Mini PCI Expansion Header .............................1-10

IDE Header..........................................................1-10

Touch Screen Controller ....................................1-10

Processor Board Connectors .............................1-11

Flash Disk ............................................................1-11

NCR Retail Specific Hardware .........................1-12

Board BIOS ..........................................................1-14

Operator Display.....................................................1-16

LCD Adapter Board ...........................................1-16

LCD Backlight Inverter Module .......................1-16

Touch Screen .......................................................1-16

NCR 7460 Integrated Customer Display .............1-17

Features...........................................................................1-18

Magnetic Stripe Reader..........................................1-18

Printer Options........................................................1-19

NCR 7194 Printer................................................1-19

7158 Printer..........................................................1-19

7194 Printer..........................................................1-20

7196 Printer..........................................................1-20

NCR 5972 2x20 Customer Display .......................1-21

Features................................................................1-22

NCR 5973 International VFD Customer Display1-23

Other Integrated Devices and Indicators ............1-24

Hard Disk Drive..................................................1-24

Power/Status LED .............................................1-24

LAN Status LEDs................................................1-25

Power Supply......................................................1-25

Chapter 2: Hardware Installation

Introduction......................................................................2-1

Installation Summary ...............................................2-1

Installation Restrictions ..................................................2-2

Connecting the Cables ....................................................2-3

Accessing the Cable Connectors and Routing

Cables..........................................................................2-3

Identifying the Cable Connectors...........................2-4

Installing Peripherals ......................................................2-5

Installing a Transaction Printer...............................2-5

7158 Printer............................................................2-5

7194 Printer............................................................2-6

Serial Modem for 7194 Printers...............................2-7

Installation Procedures ........................................2-7

7196 Printer............................................................2-8

Installing a Remote Customer Display ................2-10

NCR 5972-1000/1100 Remote Customer

Display .................................................................2-10

5973 International VFD Customer Display.....2-12

Mounting Considerations ............................................2-14

Wall Mounting the 7460 ...............................................2-15

Wall Mounting the Base Unit................................2-16

Wall Mounting the LCD Operators Display.......2-17

Installing a Cash Drawer .......................................2-19

Installing a Second Cash Drawer .....................2-20

Mini PCI 56KB Modem (7460-F210)...........................2-21

Installing the Modem .............................................2-21

Finalizing the Installation.............................................2-22

Completing the OS Installation (WinNT) .......2-22

Completing the OS Installation (Win98) .........2-23

Completing the OS Installation (Win95) .........2-24

Completing the OS Installation (DOS) ............2-24

Installing a Serial Mouse ..............................................2-25

Guidelines for Calibrating the Touch Screen ............2-26

Calibration Procedure ............................................2-26

Summary..................................................................2-28

Out-of-Box Failures .......................................................2-28

Powering Down the Terminal .....................................2-28

Chapter 3: BIOS Setup

Introduction......................................................................3-1

Entering Setup Using a Keyboard ..........................3-1

How to Select Menu Options ..................................3-1

Restoring Factory Settings .......................................3-2

Setup Menus.....................................................................3-3

Main Menu.................................................................3-3

System Time and Date .........................................3-3

Legacy Diskette.....................................................3-3

Primary Master .....................................................3-4

Advanced Menu........................................................3-5

Installed OS ...........................................................3-6

Reset Configuration Data ....................................3-6

Cache Memory......................................................3-7

PS/2 port..............................................................3-11

Large Disk Access Mode ...................................3-23

Local Bus IDE adapter .......................................3-24

Advanced Chipset Control................................3-24

PCI Configuration ..............................................3-25

System Monitors .................................................3-28

Multiple ROM Menu..........................................3-29

QuickBoot Mode.................................................3-31

After Power Failure............................................3-31

Continuous POST ...............................................3-32

Boot menu retry ..................................................3-32

LCD contrast and LCD Brightness

(Advanced Menu)...............................................3-32

Beep Error Codes (Advanced Menu)...............3-32

Security Menu Options ..........................................3-33

Set Supervisor/User Password ........................3-33

Password on Boot ...............................................3-34

Power Menu Options .............................................3-35

Power Savings.......................................................3-35

Resume On Time ................................................3-37

Resume Time.......................................................3-38

Resume On Modem Ring ..................................3-38

vii

Boot Menu Options.................................................3-39

System Boot Sequence........................................3-39

Exit Menu Options..................................................3-40

BIOS Default CMOS Values ..................................3-41

Main Values.........................................................3-41

Advanced ValuesI/O Device Configuration..3-43

PCI Configuration ..............................................3-43

I/O Addresses ...............................................................3-44

Interrupt Levels .............................................................3-46

Memory Map..................................................................3-47

Chapter 4: Operating System Recovery

Introduction......................................................................4-1

Prerequisites ..............................................................4-1

Updating Procedures................................................4-2

Completing the OS Installation (Win2000) .......4-5

Completing the OS Installation (WinNT) .........4-6

Completing the OS Installation (Win98) ...........4-6

Completing the OS Installation (Win95) ...........4-7

Completing the OS Installation (DOS) ..............4-7

Gold Disk Contents.........................................................4-8

Microsoft Operating System License

Agreements................................................................4-8

NCR 7460 Win 2000 Operating System

Recovery Software (LPIN: D370-0505-0100) .........4-9

NCR 7460-NT Operating System Recovery

Software (LPIN: D370-0496-0100).........................4-10

NCR 7460-Win98 Operating System Recovery

Software (LPIN: D370-0497-0100).........................4-11

NCR 7460-Win95 Operating System Recovery

Software (LPIN: D370-0498-0100).........................4-12

viii

NCR 7460 DOS Operating System Recovery

Software (LPIN: D370-0499-0100).........................4-12

OS Recovery from a Larger Disk Image.....................4-13

Chapter 5: BIOS Updating Procedures

Introduction......................................................................5-1

Prerequisites ..............................................................5-1

Updating Procedures................................................5-2

BIOS Crisis Recovery ......................................................5-3

Recovery Procedures ................................................5-5

Cable/Connector Pin-Out Information........................5-7

Chapter 6: NCR 7460 2x20 Customer Display

Introduction......................................................................6-1

Viewing Area.............................................................6-1

Diagnostics.................................................................6-1

Command Descriptions..................................................6-2

Structure/Logic Description ...................................6-2

Integrated Display Interface....................................6-2

Character Map...........................................................6-4

Appendix A: Cables

Appendix B: Kits

Autres manuels pour 7460

Table des matières

Autres manuels NCR Terminal tactile

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur

Prestel

Prestel VCS-G2PRO Manuel utilisateur