Moxa Technologies VPort 66-2MP Series Manuel utilisateur
P/N: 1802000661010
*1802000661010*
VPort 66-2MP Series
Quick Installation Guide
Edition 1.0, September 2015
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
+86-21-5258-9955
Fax:
+86-21-5258-5505
Moxa Europe:
Tel:
+49-89-3 70 03 99-0
Fax:
+49-89-3 70 03 99-99
Moxa Asia-Pacific:
Tel:
+886-2-8919-1230
Fax:
+886-2-8919-1231
Moxa India:
Tel:
+91-80-4172-9088
Fax:
+91-80-4132-1045
2015 Moxa Inc. All rights reserved.
- 2 -
Overview
The VPort 66-2MP is a vandal-proof, IP66-rated, PTZ speed dome IP
camera for use in harsh, outdoor environments. With a 360° endless PAN,
-6 to 96° TILT, 22X/30X optical/20X digital zoom, H.264/MJPEG triple
video streams, day-and-night camera lens, and -40 to 65°C operating
temperature, the VPort 66-2MP is especially well-suited for outdoor video
surveillance applications.
Package Checklist
Moxa’s VPort 66-2MP is shipped with the following items. If any of these
items is missing or damaged, please contact your customer service
representative for assistance.
•1 × VPort 66-2MP
Model
Lens
Power
Ethernet
VPort 66-2MP-CAM22X f=4.3 mm (wide)
to 94.6 mm (tele),
24 VDC/VAC RJ45
VPort 66-2MP-CAM30X
f=4.3 mm (wide)
to 129.0 mm (tele)
24 VDC/VAC
RJ45
•Screw handle accessory package
Torx screw driver for
attaching/detaching the top
cover.
3.5 mm power jack to 2-pin
terminal block connector for
2-wire power line connection.
Silica gel dry bag (silica gel
desiccant)
for absorbing moisture
inside the camera.
Hook-and-loop fasteners for
attaching the dry bag inside the
camera.
•Quick Installation Guide
•Documentation and software CD (includes user’s manual, Quick
Installation Guide, and utility)
•Warranty card
NOTE
Check the model name on the VPort’s side label to determine if
the model name is correct for your order.
- 3 -
NOTE
This product must be installed in compliance with your local laws
and regulations.
Features
•Maximum 60 FPS @ full HD (1080P, 1920x1080) resolution (only in
single stream mode)
•22X/30X optical and 20X digital zoom (22X: 4.3 to 94.6 mm,
30X: 4.3 to 129 mm)
•Supports MJPEG and H.264 dual codecs
•Supports Full HD/SXGA/WXGA/720P/SVGA/ Full D1/ 4CIF/ VGA/
CIF/QVGA resolution
•TCP, UDP, and HTTP network transmission modes
•Supports QoS (ToS) for transmission priority
•Supports RTSP streaming
•Supports multicast (IGMP) video streaming
•Supports SNMP (V1/V2C/V3) for network system integration and
management
•Accessible IP filtering
•UPnP supported
•Built-in web server for easy configuration
•360° endless pan and -6° to +96° tilt
•Manual max pan speed of 120°/s; Preset max of 255°/s; Alarm
Trigger max of 360°/s*
•Supports PTZ movement calibration
•Minimum illumination up to 0.4 lux (color) and 0.03 lux (B/W)
•Built-in tamper alarm and Video Motion Detection (VMD)
•-40 to 65°C operating temperature
•1 10/100BaseT(X) port with RJ45 connector
•IP66 protection and NEMA Type 4X form factor
•SDXC slot for local event / disconnected recording
•CBR Pro for flexible flow control
•DynaStream™ for network efficiency with dynamic frame rate change
•EN50121-4 compliance
•Supports ONVIF Profile S for multiple video stream profiles
•24 VDC/VAC power input
•Supports NTCIP 1205
•EN 62262 IK10 level vandal resistance
•CE, FCC, UL 60950-1
•Pre, Trigger, and post snapshot images supported
•Sequential snapshot images supported
•Supports SMTP and FTP for alarm message transmission
•Supports HTTP event server
•3-year warranty for product, and 1-year warranty for moving parts**
*
When the temperature is under -10°C, the maximum PT speed will be
reduced to a max. of 130°/sec.
**
The following moving parts come with a 1-year warranty:
•
Fan
•
Shutter
•
Zoom lens
•
DC-Iris, P-Iris lens
•
PAN, TILT and lens motors/ mechanism
•Slip ring
- 4 -
VPort 66-2MP Product Description
Appearance
•Top cover screws: Four screws used to secure the top cover.
•Top cover: The top cover can be removed to take out the camera
body for installing or re-installing the SD card.
•Zoom Lens: The VPort 66-2MP-M12 supports 2 lenses with different
optical zoom specs:
22X: f = 4.3 mm (wide) to 94.6 mm (tele), F1.6 to F4.5
30X: f = 4.3 mm (wide) to 129.0 mm (tele), F1.6 to F4.7
•Dome cover: The VPort 66-2MP has a vandal-proof PC dome cover,
satisfying EN 62262 (IEC 62262) class IK10 level.
•Mounting kit: For installing the VPort 66-2MP on a wall or pole. The
mounting kit is not included as a standard accessory with the VPort
66-2MP; it must be ordered and purchased separately. Refer to the
ordering information on the VPort 66-2MP’s datasheet or webpage for
mounting accessory information.
NOTE
The color of the dome cover can be customized based on your
installation environment. Please contact your Moxa sales
representative for information about this customization service.
Note that the color of the dome cover could decrease the light
transmittance of the video image. The darker the dome cover,
the greater the decrease of light transmittance.
Inside the camera
•Camera module: The main body of the VPort 66-2MP.
•Camera module connector: A patented connector for connecting
the camera module with the external connectors with cables.
- 5 -
•SD card socket (SDXC): The VPort 66-2MP supports the SDXC
interface, which can use SD cards with more than 64 GB of memory
for local storage of video recordings (by event or continuous
recording).
NOTE
Since video recording requires a high frequency of read and write
actions
, we recommend using high performance,
high reliability
SD cards, such as Sca
ndisk or Transcend high-end SD cards.
Most important
ly, we highly recommend backing up videos
recorded
on an SD card to a
video recorder, hard disk, or other
more permanent storage media.
External cables and connectors
•Power connector: The VPort 66-2MP supports one 24 VDC or 24
VAC power input, with a 3.5 mm power jack male connector. You can
use a standard 24 VDC/VAC power adapter (3 A min.) to power the
VPort 66-2MP. In addition, a 3.5 mm power jack to 2-pin terminal
block connector is included as a standard VPort 66-2MP accessory for
direct power line connections.
VPort 66-2MP Power Consumption Information
Heater/Fan
Operation
PTZ
Operation
Temp. (inside
the camera)
Power
consumption
Heater/Fan off
Off
0 to 35°C
19 watts
Heater/Fan off
Operating
27 watts
Heater/Fan on
Off
-40 to 0°C
67 watts
Heater/Fan on
Operating
71 watts
Heater off / Fan on
Off
≥35°C
24 watts
Heater off / Fan on
Operating
31 watts
- 6 -
NOTE
•The heater and fan will be enabled when the internal
temperature is under -
10°C, and disabled when above 0°C.
The fan will be enabled when the internal temperature is
above 50°C, and disabled when under 35°C.
•
When using the 3.5 mm power jack to 2-pin terminal block
connector for a direct power line connection, be sure to pay
attention to the “+” and “-“ pin assignments on the
connector.
•
The power input rating of the VPort 66-
2MP is 24 VDC (21.6
to 26.4 VDC) or 24 VAC (21.6 to 26.4 VAC).
•Reset button: For rebooting and restoring factory defaults.
Reboot: Press the button once.
Factory default: Press and hold the button for at least 10
seconds.
•RJ45 Ethernet connector: The RJ45 Ethernet port is for 10/100
Mbps network transmission.
•5-pin terminal block connector for DI/Relay: The VPort 66-2MP
supports 1 DI (digital input) and 1 relay output.
Relay
Output
N.C.
(normal close)
Max. 1 A, 24 VDC
Initial status is
Normal Open
COM (common)
NO
(normal open)
DI DI: I+
High:
+13 V to +30 V
Low:
-30 V to +3 V
GND:
⊥
•4-pin terminal block for audio input/output: The VPort 66-2MP
supports 1 audio input and 1 audio output for an external microphone
and external speaker.
Audio input
IN +
Audio input +
IN -
Audio input -
Audio output
OUT -
Audio output -
OUT +
Audio output +
•Grounding: Attach the grounding cable with attachment ring to the
mounting kit’s grounding screw (inside the mounting kit box) to
ground the VPort 66-2MP.
- 7 -
•Safety Rope: For easier installation, use the safety rope to hook the
camera to the mounting kit buckle.
Hardware Installation
A mounting kit is required to install the VPort 66-2MP. Below we use the
VP-520LB to illustrate; the installation method of other accessories is
similar.
Step 1: Open and remove the top cover.
Use the security torx to loosen the 4 top cover screws.
Step 2: Installing an SD card requires removing the camera
module.
1. Loosen the 2 anti-drop Phillips screws, which hold the camera
module in place.
- 8 -
2. Pull the camera module a little and turn it clockwise to remove the
camera module from the camera module connector.
3. Insert the SD card, and then install the camera module by rotating
the camera module connector counterclockwise. Screw in the 2
anti-drop Phillips screws.
NOTE
If you have difficulty removing the camera module from the
camera module connector,
position the camera module in a
downwards direction. Doing so will make it easier to turn the
camera module clockwise.
Step 3: Install the sunshield (VP-SH1) if required
The VP-SH1 sunshield can be used with the VPort 66-2MP to prevent
direct sunlight from shining on the housing. Using the sunshield could be
warranted since sunlight can affect the heat dissipation mechanism.
1.
Loosen the 4 security screws
on the top of the camera.
- 9 -
2. Remove the black mount kit
and put the VP-SH1 on the
housing. Use the 3 small
Phillips screws in the
VP-SH1’s package to fix the
VP-SH1 to the housing.
3. Replace the black mount kit
tighten the 4 security screws
.
Step 4: Fasten the dry bag inside the housing
Use the hook-and-loop fastener to attach the dry bag to the camera
housing.
1.
Remove the dry bag from the package stick it
to the hook fastener.
2.
Attach the other side of the hook fastener to
the internal wall of the camera housing. Be
sure not to place
the dry bag on top of the 2
Phillips screws since the dry bag
will block the
way when removing the camera module.
- 10 -
Step 5: Close the top cover and screw in the 4 top cover screws
immediately (5.5 kgf-cm torque is recommended)
NOTE
The dry bag will absorb moisture inside the camera to prevent
m
oisture from condensing on the inside of the
transparent dome
when
the camera is used in low temperature environments.
Install the dry bag and replace the camera’s top cover
immediately after o
pening the dry bag and exposing it to the
atmosphere.
Step 6: Install the VPort 66-2MP on the VP-520LB mounting kit
1. Loosen the 3 socket set screws on the VP-520LB tube.
2. Loosen the 4 Phillips screws on the front cover, the stud bolts inside
the front cover, and the ground screw inside the box, and then pull
the bolt from the hinge to separate the front cover and the box.
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Moxa Technologies Matériel informatique
Moxa Technologies
Moxa Technologies ThinkCore DA-660-16-LX Manuel utilisateur
Moxa Technologies
Moxa Technologies RKP-A110 Series Manuel utilisateur
Moxa Technologies
Moxa Technologies CCG-1500 Series Manuel utilisateur
Moxa Technologies
Moxa Technologies UC-8100 Series Manuel utilisateur
Moxa Technologies
Moxa Technologies CP-118U Series Manuel utilisateur
Moxa Technologies
Moxa Technologies THINKCORE W311 Manuel utilisateur
Moxa Technologies
Moxa Technologies MAR-2000 Instructions d'utilisation
Moxa Technologies
Moxa Technologies THINKCORE W311 Manuel utilisateur
Moxa Technologies
Moxa Technologies WAPN008-1 Manuel utilisateur
Moxa Technologies
Moxa Technologies DA-661 Manuel utilisateur
Moxa Technologies
Moxa Technologies ioLogik 2500 Series Manuel utilisateur
Moxa Technologies
Moxa Technologies Industio CI-132 Series Manuel utilisateur
Moxa Technologies
Moxa Technologies CP-118U Series Manuel utilisateur
Moxa Technologies
Moxa Technologies ABC-02-USB Manuel utilisateur
Moxa Technologies
Moxa Technologies WAPN008 Manuel utilisateur
Moxa Technologies
Moxa Technologies UPort 200A Series Manuel utilisateur
Moxa Technologies
Moxa Technologies MPC-2101 Series Manuel utilisateur
Moxa Technologies
Moxa Technologies ABC-02-USB-T Manuel utilisateur
Moxa Technologies
Moxa Technologies C168P Manuel utilisateur
Moxa Technologies
Moxa Technologies CP-102N-T Manuel utilisateur
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
