Milwaukee MW500 Manuel utilisateur

USER MANUAL

PORTABLE

ORP METER

MODEL: MW500

Smart ORP Meter

ISTMW500 01/10

SPECIFICATIONS:

MW500

RANGE ±1000 mV

RESOLUTION 1 mV

ACCURACY (@25°C) ±5 mV

TYPICAL EMC DEVIATION ±5 mV

ORP ELECTRODE MA921B/1 (included)

ENVIRONMENT 0 to 50°C, 95% RH max.

BATTERY TYPE 9V alkaline (included)

BATTERY LIFE approximately 300 hours of use

DIMENSIONS 143 x 80 x 32 mm

WEIGHT 220 g (with battery) meter only

OPTIONAL ACCESSORIES:

M10000B Electrode rinse solution, 20 mL sachet (25 pcs)

MA9015 Electrode storage solution, 220 mL bottle

MA9020 200-275 mV ORP solution, 220 mL bottle

MA921B/1 Platinum ORP electrode with 1 m cable

WARRANTY:

This instrument is warranted from all defects in materials and manufacturing

for a period of two years from the date of purchase.

The electrode is warranted for a period of six months.

If during this period, the repair or replacement of parts is required, where the

damage is not due to negligence or erroneous operation by the user, please

return the parts to either dealer or our office and the repair will be effected

free of charge.

Note: We reserve the right to modify the design, construction and appearance

of our products without advance notice.

Milwaukee

OPERATION:

• The meter is supplied complete with a 9V battery. Slide off

the battery compartment cover located on the back of the

meter. Install the battery into the battery clip connector

while observing polarity.

• Always remove the electrode protective cap before taking

any measurement. If the electrode has been left dry, soak

the tip in storage solution for a few minutes to reactivate it.

• Connect the ORP electrode to the BNC socket on the top

of the meter.

• Immerse the tip (2.5 cm) of

the ORP electrode into the

sample.

• Turn the instrument on by

pressing the ON/OFF key.

• Allow the reading to stabilize

before taking measurements.

• After use, switch the meter

off and store the electrode

with a few drops of storage

solution in the protective

cap.

• The meter is factory

calibrated. ORP electrodes

are interchangeable and no

mV calibration is needed

when they are replaced.

MAINTENANCE:

• The surface of the ORP electrode must always be clean.

Use M10000B rinse solution for this purpose. If needed,

clean the Platinum tip with very fine abrasive paper.

• When not in use, the tip (reference junction) of the electrode

should always be kept moist and safe from any mechanical

stress.

BATTERY REPLACEMENT:

When the battery becomes weak the meter will display " ",

the low battery indicator. The battery has about 50 hours of working

time left. A low battery will result in unreliable measurements.

Prompt battery replacement is required.

Battery replacement must only take place in a non hazardous

area using an alkaline 9V battery.

Turn the meter off, slide the battery compartment cover located

at the rear of the meter off and replace the 9V battery with a

new one. Make sure the battery contacts are fully engaged in

the connector, seat the battery in its compartment and replace

the cover.

Autres manuels Milwaukee Instrument de mesure

Milwaukee

Milwaukee 2205-40 Manuel utilisateur

Milwaukee

Milwaukee 2217-40 Manuel utilisateur

Milwaukee

Milwaukee MW301 Manuel utilisateur

Milwaukee

Milwaukee 2205-20 Manuel utilisateur

Milwaukee

Milwaukee MW806 MAX Manuel utilisateur

Milwaukee

Milwaukee M12 3PL Manuel utilisateur

Milwaukee

Milwaukee MW100 Manuel utilisateur

Milwaukee

Milwaukee MW803 Manuel utilisateur

Milwaukee

Milwaukee 3631-20 Manuel utilisateur

Milwaukee

Milwaukee SM101 Manuel utilisateur

Milwaukee

Milwaukee pH52 Manuel utilisateur

Milwaukee

Milwaukee LDM 30 Manuel utilisateur

Milwaukee

Milwaukee 2235-20 Manuel utilisateur

Milwaukee

Milwaukee MW11 Manuel utilisateur

Milwaukee

Milwaukee MC110 Manuel utilisateur

Milwaukee

Milwaukee PH55 Manuel utilisateur

Milwaukee

Milwaukee MR32ATC Manuel utilisateur

Milwaukee

Milwaukee MA888 Manuel utilisateur

Milwaukee

Milwaukee MI 404 Manuel utilisateur

Milwaukee

Milwaukee CALIBRATION 2238-20 Manuel utilisateur

Milwaukee

Milwaukee C65 Manuel utilisateur

Milwaukee

Milwaukee MC510 Manuel utilisateur

Milwaukee

Milwaukee PRO Lux MW700 Manuel utilisateur

Milwaukee

Milwaukee HEAVY DUTY 7,5 m LED Tape Measure Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur