Milwaukee MC510 Manuel utilisateur

SPECIFICATIONS: MC510

RANGE ±1000 mV

RESOLUTION 1 mV

ACCURACY (@25°C) ±5 mV

SETPOINT 0 to 600 mV

ALARM active when the measure is

lower/higher than setpoint

depending on user selection

OUTPUT POWER SOCKET active when the measure is

higher/lower than selected setpoint

(5A max) depending on user selection

ORP ELECTRODE MA921B/2 (included)

ENVIRONMENT 0 to 50°C, 95% RH max.

POWER SUPPLY 12 VDC (included)

POWER DRIVERS 2A, 60Hz or 230VAC, 1A, 50Hz

DIMENSIONS 148.5 x 82.5 x 32 mm

WEIGHT 180 g (meter only)

OPTIONAL ACCESSORIES:

MA921B/2 ORP Electrode with BNC connector and 2m cable

M10000B Electrode rinse solution, 20 mL sachet (25 pcs)

MA9015 Electrode storage solution, 220 mL bottle

WARRANTY:

This instrument is warranted from all defects in materials and manufacturing for a period of two

years from the date of purchase. The electrode is warranted for a period of 6 months.

If during this period, the repair or replacement of parts is required, where the damage is not due to

negligence or erroneous operation by the user, please return the parts to either dealer or our office

and the repair will be effected free of charge

Note: We reserve the right to modify the design, construction and appearance of our products

without advance notice.

USER MANUAL

PORTABLE

ORP METER

MODEL: MC510

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com

OPERATION:

•Connect the supplied 12

VDC power adapter to the

meter and to the mains line.

•Connect the ORP electrode

to the BNC socket on the

bottom of the meter.

•Always remove the elec-

trode protective cap before

taking any measurement. If

the electrode has been left

dry, soak the tip (bottom 2.5

cm) in rinse solution

(M10000B) for a few minutes to reactivate it.

•Turn the instrument on by pressing the ON/OFF key.

•Allow the reading to stabilize and the meter will start continuous

monitoring.

•The meter is factory calibrated.

•A blinking alarm will indicate when the measured ORP value is lower or

higher than the setpoint, depending on user selection.

NOTE:

•The power contact is not protected by fuse inside the meter. It is

recommended to protect it outside, against failure.

•WARNING: when the alarm led is blinking, the mains voltage is

present in the output power socket.

SETPOINT:

•The setpoint can be selected by

adjusting the central front knob to the

desired value.

•The selectable range for MC510 is

from 0 to 600 mV.

•The nature of the setpoint can be selected by setting the switch to the

desired position (ABOVE or BELOW).

INSTALLATION PROCEDURE:

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com

Autres manuels Milwaukee Instrument de mesure

Milwaukee

Milwaukee MW700 Manuel utilisateur

Milwaukee

Milwaukee MW11 Manuel utilisateur

Milwaukee

Milwaukee MC110 Manuel utilisateur

Milwaukee

Milwaukee C 12 IC AVD Manuel utilisateur

Milwaukee

Milwaukee MW13 Manuel utilisateur

Milwaukee

Milwaukee MI 413 Manuel utilisateur

Milwaukee

Milwaukee SMS510 Manuel utilisateur

Milwaukee

Milwaukee 2231-20 Manuel utilisateur

Milwaukee

Milwaukee 2235-40 Manuel utilisateur

Milwaukee

Milwaukee MW11 Manuel utilisateur

Milwaukee

Milwaukee M12 3PL Manuel utilisateur

Milwaukee

Milwaukee Mi170 Manuel utilisateur

Milwaukee

Milwaukee EC40 Manuel utilisateur

Milwaukee

Milwaukee MW102 Manuel utilisateur

Milwaukee

Milwaukee MC310 Manuel utilisateur

Milwaukee

Milwaukee REDLITHIUM Manuel utilisateur

Milwaukee

Milwaukee M12 CLLP Manuel utilisateur

Milwaukee

Milwaukee MI408 Manuel utilisateur

Milwaukee

Milwaukee MW101 Manuel utilisateur

Milwaukee

Milwaukee PRO MI414 Manuel utilisateur

Milwaukee

Milwaukee CALIBRATION 2238-20 Mode d'emploi

Milwaukee

Milwaukee 3631-20 Manuel utilisateur

Milwaukee

Milwaukee MW180 MAX Manuel utilisateur

Milwaukee

Milwaukee pH54 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur