Milwaukee MW100 Manuel utilisateur

USER MANUAL

MW100

PRO pH Meter

milwaukeeinstruments.com (USA & CAN)

milwaukeeinst.com

SPECIFICATIONS

RANGE 0.0 to 14.0 pH

RESOLUTION 0.1 pH

ACCURACY (@25°C) ±0.2 pH

TYPICAL

EMC DEVIATION

±0.1 pH

pH ELECTRODE SE-220 (included)

ENVIRONMENT 0 to 50°C, 95% RH max.

BATTERY TYPE 1 x 9V alkaline (included)

BATTERY LIFE

approximately 300 hours

of use

DIMENSIONS 143 x 80 x 32 mm

WEIGHT 220 g (with battery)

meter only

CERTIFICATION

Milwaukee Instruments conform to the

CEEuropean Directives.

Disposal of Electrical & Electronic

Equipment. Do not treat this product as

household waste. Hand it over to the

appropriate collection point for the recycling of

electrical and electronic equipment.

Disposal of waste batteries. This product

contains batteries. Do not dispose of them

with other household waste. Hand them

over to the appropriate collection point for recycling.

Please note: proper product and battery disposal

prevents potential negative consequences for human

health and the environment. For detailed information,

contact your local household waste disposal service or

go to www.milwaukeeinstruments.com (USA & CAN)

or www.milwaukeeinst.com.

RECOMMENDATION

Before using this product, make sure it is entirely

suitable for your specific application and for the

environment in which it is used. Any modification

introduced by the user to the supplied equipment

may compromise the meter’s performance. For your

and the meter’s safety do not use or store the meter in

hazardous environment. To avoid damage or burn, do

not perform any measurement in microwave ovens.

WARRANTY

This instrument is warranted against defects in

materials and manufacturing for a period of 2years

from the date of purchase. Probe is warranted for

6 months. This warranty is limited to repair or free

of charge replacement if the instrument cannot be

repaired. Damage due to accidents, misuse, tampering

or lack of prescribed maintenance is not covered by

warranty. If service is required, contact your local

Milwaukee Instruments Technical Service. If the repair

is not covered by the warranty, you will be notified of

the charges incurred. When shipping any meter, make

sure it is properly packaged for complete protection.

Milwaukee Instruments reserves the right to make

improvements in design, construction and appearance

of its products without advance notice.

SATISFACTION

GUARANTEED

ISTMW100 07/20

OPERATION

yThe meter is supplied complete with a 9V battery.

Slide o the battery compartment cover on the back

of the meter. Install the battery into the battery clip

connector while observing polarity.

yAlways remove the electrode protective cap before

taking any measurement. If the electrode has been

left dry, soak the tip (bottom 2.5 cm) in rinse solution

(M10000B) for a few minutes to reactivate it.

yConnect the pH electrode to the BNC socket on the

top of the meter.

yMake sure that the meter has been calibrated

before taking any measurements (see Calibration

Procedure).

yImmerse the tip (2.5 cm) of the pH electrode into the

sample.

yTurn the instrument on by pressing the ON/OFF key.

yAllow the reading to stabilize before taking

measurements.

yAfter measurements, switch the meter o and store

the electrode with a few drops of storage solution

(SE-220) in the protective cap.

CALIBRATION PROCEDURE

yRemove the protective cap from the electrode.

yRinse tip o with distilled water or a small quantity

of pH 7.

yImmerse the electrode tip into a new sachet of pH7

calibration solution and allow the reading to stabilize.

yAdjust the pH7 (OFFSET) calibration trimmer to display

“7.0pH”.

yOpen a new sachet of pH4 calibration solution and

use a small quantity to rinse the electrode.

yImmerse the electrode tip inside the pH4 sachet and

allow the reading to stabilize.

yAdjust the pH4/pH10 (SLOPE) calibration trimmer to

read “4.0 pH”.

yThe calibration is now complete and the meter is

ready to take measurements.

yIt is suggested the meter be calibrated at least once a

month, after a prolonged period of inactivity, and after

electrode replacement.

BATTERY REPLACEMENT

When the battery becomes weak the meter will

display “ “.

When the low battery indicator appears, the battery has

only about 50 hours of working time left. A low battery will

result in unreliable measurements.

Prompt battery replacement is required. Battery

replacement must only take place in a non-hazardous

area using an alkaline 9V battery.

Turn the meter o, slide the battery compartment

cover located at the rear of the meter o and replace

the 9V battery with a new one. Make sure the battery

contacts are fully engaged in the connector, seat the

battery in its compartment and replace the cover.

OPTIONAL ACCESSORIES

M10004B pH 4.01 buer solution,

20 mL sachet (25 pcs)

M10007B pH 7.01 buer solution,

20 mL sachet (25 pcs)

M10010B pH 10.01 buer solution,

20 mL sachet (25 pcs)

M10000B Electrode rinse solution,

20 mL sachet (25 pcs)

MA9015 Electrode storage solution,

220 mL bottle

MA950 Portable meter wall mounting kit

SE-220

pH electrode with BNC connector and

1 m cable

Autres manuels Milwaukee Instrument de mesure

Milwaukee

Milwaukee L4 CLL Manuel utilisateur

Milwaukee

Milwaukee MI406 Manuel utilisateur

Milwaukee

Milwaukee pH52 Manuel utilisateur

Milwaukee

Milwaukee PH55 Manuel utilisateur

Milwaukee

Milwaukee MW190 Manuel utilisateur

Milwaukee

Milwaukee 48-22-9802 Manuel utilisateur

Milwaukee

Milwaukee PRO Lux MW700 Manuel utilisateur

Milwaukee

Milwaukee MW14 Manuel utilisateur

Milwaukee

Milwaukee MI806 Manuel utilisateur

Milwaukee

Milwaukee MA882 Manuel utilisateur

Milwaukee

Milwaukee MI407 Manuel utilisateur

Milwaukee

Milwaukee MI411 Manuel utilisateur

Milwaukee

Milwaukee SM500 Manuel utilisateur

Milwaukee

Milwaukee M12 SPL Manuel utilisateur

Milwaukee

Milwaukee MI 806 Manuel utilisateur

Milwaukee

Milwaukee M12 CLLP-301C Manuel utilisateur

Milwaukee

Milwaukee MW700 Manuel utilisateur

Milwaukee

Milwaukee MW180 MAX Manuel utilisateur

Milwaukee

Milwaukee 2270-20 Manuel utilisateur

Milwaukee

Milwaukee CALIBRATION 2238-20 Manuel utilisateur

Milwaukee

Milwaukee 2217-40 Manuel utilisateur

Milwaukee

Milwaukee PH55 Manuel utilisateur

Milwaukee

Milwaukee MA872 Manuel utilisateur

Milwaukee

Milwaukee ORP 57 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur