Milwaukee MC110 Manuel utilisateur

SPECIFICATIONS:

MC110 MC120 MC122

RANGE 0.0 to 14.0 pH

RESOLUTION 0.1 pH

ACCURACY (@25°C) ±0.2 pH

SETPOINT 3.5 to 7.5 pH 5.5 to 9.5 pH

ALARM active when measure is

higher/lower than selected setpoint

depending on user selection

OUTPUT POWER SOCKET active when measure is

(for MC122 only) higher/lower than selected setpoint (5A max)

depending on user selection

POWER DRIVERS 115VAC, 2A, 60Hz or 230VAC, 1A, 50Hz

(for MC122 only)

pH ELECTRODE MA911B/2 (included)

ENVIRONMENT 0 to 50°C, 95% RH not condensing

POWER SUPPLY 12 VDC (included)

DIMENSIONS 148.5 x 82.5 x 32 mm

WEIGHT MC110, MC120 160 g (meter only)

MC122 180 g

OPTIONAL ACCESSORIES:

M10004B pH 4.01 buffer solution, 20 ml sachet (25 pcs)

M10007B pH 7.01 buffer solution, 20 ml sachet (25 pcs)

M10010B pH 10.01 buffer solution, 20 ml sachet (25 pcs)

M10000B Electrode rinse solution, 20 ml sachet (25 pcs)

MA9015 Electrode storage solution, 20 ml sachet (25 pcs)

WARRANTY:

These instruments are warranted from all defects in materials and manufacturing for a

period of two years from the date of purchase. The electrode is warranted for a period

of 6 months.

If during this period, the repair or replacement of parts is required, where the damage is

not due to negligence or erroneous operation by the user, please return the parts to

either dealer or our office and the repair will be effected free of charge.

Note: We reserve the right to modify the design, construction and appearance of ourproducts without

advance notice.

MANUAL

PORTABLE pH METER

MODELS: MC110 -MC120 -MC122

OPERATION

• Connect the supplied 12VDC power

adapter to the meter and to the

mains line.

• Connect the pH-electrode to the

BNC socket on the bottom of the

meter.

• Always remove the electrode

protective cap before taking any

measurement. If the electrode has

been left dry, soak the tip (bottom

2.5 cm) in M10000B rinse solution

for a few minutes to reactivate it 12VDC O" RELAY OUTPUT

12VDC pH RELAY

ADAPTER ELECTRODE OUTPUT

• Make sure that the meter has been calibrated before taking any

measurements (see Calibration Procedure).

• Immerse the tip (2.5 cm) of the pH-electrode into the sample.

• Turn the instrument on by pressing the ON/OFF key.

• Allow the reading to stabilize and the meter will start continuous

monitoring.

• A blinking alarm will indicate when the measured pH value is higher or

lower than selected setpoint, depending on user selection.

NOTE.The output power contact (MC122 only) has no protection fuse

inside the meter. It is recommended to protected it outside, against

failure.

SETPOINT

The setpoint can be selected by

adjusting the central front knob to the

desired value.

• The selectable range is from 3.5 to

7.5 pH for MC110; from 5.5 to 9.5 pH

for MC120 and MC122.

• The nature of the setpoint can be

selected by setting the switch to the

desired position (ABOVE or BELOW).

CALIBRATION PROCEDURE

•Remove the protective cap from the electrode.

•Immerse the electrode tip into a new sachet of pH 7

calibration solution and allow the reading to stabilize.

•Adjust the pH7 calibration trimmer (on the front) to

display "7.0 pH".

•Open a new sachet of pH 4 calibration solution and

use a small quantity to rinse the electrode.

•Immerse the electrode tip into the pH 4 sachet and

allow the reading to stabilize.

•Adjust the pH4/10 calibration trimmer (on the front) to

display "4.0 pH".

•The calibration is now complete and the meter is

ready to take measurements.

•It is suggested to recalibrate the meter at least

once a month, after a prolonged stocking time

and after pH-electrode replacement.

INSTALLA TION PROCEDURE

(for MC122 only) :

Ce manuel convient aux modèles suivants

Autres manuels Milwaukee Instrument de mesure

Milwaukee

Milwaukee REDLITHIUM L4 CLL, REDLITHIUM L4 CPL Manuel utilisateur

Milwaukee

Milwaukee REDLITHIUM Manuel utilisateur

Milwaukee

Milwaukee MW 14 Manuel utilisateur

Milwaukee

Milwaukee MI 106 Manuel utilisateur

Milwaukee

Milwaukee 48-22-9801 Manuel utilisateur

Milwaukee

Milwaukee 2205-20 Manuel utilisateur

Milwaukee

Milwaukee MW190 Manuel utilisateur

Milwaukee

Milwaukee Mi 150 Manuel utilisateur

Milwaukee

Milwaukee 3631-20 Manuel utilisateur

Milwaukee

Milwaukee 2280-20 Manuel utilisateur

Milwaukee

Milwaukee 2217-40 Manuel utilisateur

Milwaukee

Milwaukee 2270-20 Manuel utilisateur

Milwaukee

Milwaukee MI 413 Manuel utilisateur

Milwaukee

Milwaukee MI413 PRO Manuel utilisateur

Milwaukee

Milwaukee MW10 Manuel utilisateur

Milwaukee

Milwaukee MI 404 Manuel utilisateur

Milwaukee

Milwaukee CD600 Manuel utilisateur

Milwaukee

Milwaukee MW100 Manuel utilisateur

Milwaukee

Milwaukee CALIBRATION 2238-20 Manuel utilisateur

Milwaukee

Milwaukee MW803 Manuel utilisateur

Milwaukee

Milwaukee SM801 Manuel utilisateur

Milwaukee

Milwaukee Heavy Duty 2270-20 Manuel utilisateur

Milwaukee

Milwaukee pH54 Manuel utilisateur

Milwaukee

Milwaukee SMS510 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur