Linksys LNE100M Manuel utilisateur

Instant EtherFast®Series

EtherFast®10/100

Managed Network

Adapter

Use this guide to install: LNE100M User Guide

are registered trademarks of Linksys. Microsoft, Windows, and the Windows logo are reg-

istered trademarks of Microsoft Corporation. All other trademarks and brand names are

the property of their respective proprietors.

LIMITED WARRANTY

Linksys guarantees that every EtherFast®10/100 Managed Network Adapter is free from

physical defects in material and workmanship for the lifetime of the Adapter, when used

within the limits set forth in the Specifications section of this User Guide. If the product

proves defective during this warranty period, call Linksys Technical Support in order to

obtain a Return Authorization number. BE SURE TO HAVE YOUR PROOF OF PUR-

CHASE ON HAND WHEN CALLING. RETURN REQUESTS CANNOT BE PROCESSED

WITHOUT PROOF OF PURCHASE. When returning a product, mark the Return

Authorization number clearly on the outside of the package and include a copy of your

original proof of purchase. All customers located outside of the United States of America

and Canada shall be held responsible for shipping and handling charges.

IN NO EVENT SHALL LINKSYS LIABILITY EXCEED THE PRICE PAID FOR THE

PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES RESULTING FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING

SOFTWARE, OR ITS DOCUMENTATION. Linksys makes no warranty or representation,

expressed, implied, or statutory, with respect to its products or the contents or use of this

documentation and all accompanying software, and specifically disclaims its quality, per-

formance, merchantability, or fitness for any particular purpose. Linksys reserves the right

to revise or update its products, software, or documentation without obligation to notify

any individual or entity. Please direct all inquiries to:

Linksys P.O. Box 18558, Irvine, CA 92623.

FCC STATEMENT

The EtherFast®10/100 Managed Network Adapter has been tested and complies with the

specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a res-

idential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used according to the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which is found by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following meas-

ures:

 Reorient or relocate the receiving antenna

 Increase the separation between the equipment or device

 Connect the equipment to an outlet other than the receivers

 Consult a dealer or an experienced radio/TV technician for assistance

UG-LNE100M-090602NC KL

Instant EtherFast

Series EtherFast

10/100 Managed Network Adapter

CChhaapptteerr77::MMaannuuaallIInnssttaallllaattiioonn

aannddSSeettuuppffoorrWWiinnddoowwssNNTT2277

Overview 27

Installing NT Networking and the Adapter’s Driver 28

Installing the Adapter’s Driver if Networking is Already Installed 33

CChhaapptteerr88::MMaannuuaallIInnssttaallllaattiioonn

aannddSSeettuuppffoorrWWiinnddoowwss220000003366

Overview 36

Installing the Adapter's Driver 36

CChhaapptteerr99::MMaannuuaallIInnssttaallllaattiioonn

aannddSSeettuuppffoorrWWiinnddoowwssXXPP4400

Overview 40

Installing the Adapter's Newest Driver 40

CChhaapptteerr1100::CCoonnffiigguurriinnggtthheeAAddaapptteerr4422

Overview 42

General Tab 43

Advanced Tab 44

Driver Tab 48

Resources Tab 49

Power Management Tab 49

CChhaapptteerr1111::UUssiinnggtthheeAAddaapptteerr’’ss

NNIICCCCoonnttrroollSSeettaannddDDiiaaggnnoossttiiccTToooollss5500

Running the Control Set 50

General Tab 51

Setting Tab 52

Statistics Tab 57

Diagnostics Tab 62

Table of Contents

CChhaapptteerr11::IInnttrroodduuccttiioonn11

The EtherFast®10/100 Managed Network Adapter 1

Features 1

Package Contents 2

Minimum Requirements 2

CChhaapptteerr22::GGeettttiinnggttooKKnnoowwtthhee

EEtthheerrFFaasstt®®1100//110000MMaannaaggeeddNNeettwwoorrkkAAddaapptteerr33

LEDs 3

The RJ-45 Port 3

CChhaapptteerr33::IInnssttaalllliinnggtthheeAAddaapptteerr44

Overview 4

Installing the Adapter and Cabling 4

CChhaapptteerr44::IInnssttaalllliinnggtthheeAAddaapptteerr’’ssDDrriivveerrsswwiitthhtthhee

SSeettuuppUUttiilliittyyCCDD77

Overview 7

Using the Setup Utility 7

CChhaapptteerr55::MMaannuuaallIInnssttaallllaattiioonn

aannddSSeettuuppffoorrWWiinnddoowwss9988SSEE1100

Overview 10

Installing the Adapter's Driver 10

Network Component Configuration 14

CChhaapptteerr66::MMaannuuaallIInnssttaallllaattiioonn

aannddSSeettuuppffoorrWWiinnddoowwssMMee1199

Overview 19

Installing the Adapter's Driver 19

Network Component Configuration 22

AAppppeennddiixxJJ::TThheeSSeettuuppUUttiilliittyyCCDD9933

AAppppeennddiixxKK::GGlloossssaarryy9944

AAppppeennddiixxLL::SSppeecciiffiiccaattiioonnss110033

Environmental 103

AAppppeennddiixxMM::WWaarrrraannttyyIInnffoorrmmaattiioonn110044

AAppppeennddiixxNN::CCoonnttaaccttIInnffoorrmmaattiioonn110055

Instant EtherFast

Series

AAppppeennddiixxAA::TTrroouubblleesshhoooottiinngg6644

Common Problems and Solutions 64

Running the Adapter's Diagnostics 68

AAppppeennddiixxBB::MMaannaaggiinnggtthheeAAddaapptteerr

tthhrroouugghhSSNNMMPPaannddtthheeRRMMOONNAAggeenntt6699

Overview 69

Installing SNMP for Windows 98SE and Me 69

Installing SNMP for Windows NT 72

Installing SNMP for Windows 2000 and XP 74

Adding the Adapter’s SNMP Agent 76

Utilizing the Adapter’s SNMP Agent 76

AAppppeennddiixxCC::SShhaarriinnggYYoouurrFFiilleessaannddPPrriinntteerrss7788

Overview 78

Enabling File Sharing 78

Enabling Printer Sharing 79

AAppppeennddiixxDD::WWiinnddoowwss9988aannddMMeeCClliieenntt

ffoorrWWiinnddoowwssDDoommaaiinnSSeerrvveerr8800

AAppppeennddiixxEE::SSttaarrttiinnggOOvveerriinn

WWiinnddoowwss9988,,MMee,,22000000,,oorrXXPP8822

Starting Over in Windows 98 or Me 82

Starting Over in Windows 2000 or XP 84

AAppppeennddiixxFF::MMaannuuaallllyyIInnssttaalllliinnggtthheeNNeettwwoorrkk

CCoommppoonneennttssiinnWWiinnddoowwss9988aannddMMee8866

AAppppeennddiixxGG::IInnssttaalllliinnggtthheeNNeettwwoorrkkPPrroottooccoollss

ffoorrWWiinnddoowwss9988aannddMMee8888

AAppppeennddiixxHH::AAbboouuttPPlluugg--aanndd--PPllaayyTTeecchhnnoollooggyy9900

AAppppeennddiixxII::UUnniinnssttaalllliinnggtthheeDDrriivveerrss

wwiitthhtthheeIInnssttaallllWWiizzaarrdd9922

EtherFast

10/100 Managed Network Adapter

• One EtherFast®10/100 Managed Network Adapter

• One Setup Utility CD

• One User Guide (included on the Setup Utility CD)

• One Registration Card (not shown)

• Quick Install for Windows Operating Systems (not shown)

• 200MHz or Faster CPU

• Available PCI 2.2 Slot

• CD-ROM Drive

• Windows 98/Me/NT 4.0/2000/XP

Instant EtherFast

Series

Chapter 1: Introduction

This powerful auto-negotiating 10/100 Mbps Ethernet interface card features

network management functions to save you time and hassle. Configure, check

error rates, and keep an inventory of your network resources from one central-

ized location.

The Wake-On-LAN function remotely "wakes up" any PC on the network, so

you can handle maintenance chores during off-hours. The 802.1Q support lets

you optimize your network traffic by dividing the network into smaller Virtual

LANs, while packet delivery is prioritized using 802.1P signaling.

• Easy to Use Plug-and-Play 10/100 PCI Network Adapter

• Adapter settings can be managed via SNMP using standard MIB browser

• Full Duplex Capability at Up To 200Mbps

• Connects to Both 10Mbps Ethernet and 100Mpbs Fast Ethernet Networks

• Power On your PC from anywhere on the network with Wake-On-LAN

Management

• Complete 802.1Q VLAN support for use in segmented networks

• Support for IP Checksum offloading built-into the adapter driver

• 802.1p tagging support for Quality of Service (QoS)

• Configuration utility allows for complete management of the network

adapter settings

Package Contents

Features

The EtherFast®10/100 Managed Network Adapter

Minimum Requirements

EtherFast

10/100 Managed Network Adapter

Figure 1-1

Chapter 3: Installing the Adapter

Each Adapter is equipped with an RJ-45 port that automatically adjusts to

either 10Mbps or 100Mbps speeds, allowing your PC to attach to either Fast

Ethernet (also known as 100BaseTX) or regular 10BaseT Ethernet network

segments without additional hardware or software.

The Adapter should only be used with twisted-pair cabling. 10BaseT and

100BaseTX cabling is available in a number of different grades. For best

results, use 8-wire, UTP Category 5 unshielded twisted-pair for both 10BaseT

and 100BaseTX network segments, although UTP Category 3 can be used for

10BaseT segments. The cable that runs from the Adapter to your network

should not exceed 100 meters (328 feet).

1. Power off your PC and any peripheral equipment attached to it. Unplug

your PC’s power cable.

2. Remove your computer's outside cover.

Overview

Installing the Adapter and Cabling

Instant EtherFast

Series

Chapter 2: Getting to Know the

EtherFast®10/100 Managed

Network Adapter

100 Yellow. The 100 LED will illuminate when the Adapter is operat-

ing at 100Mbps. If the 100 LED is not illuminated and the PC is

powered on, the card is operating at 10Mbps.

Link/Act Green. The Link LED will illuminate when the Adapter has been

successfully connected to a network and flicker when data is being

transmitted or received over the network.

COL Green. The COL LED will illuminate when the Adapter experi-

ences any collisions.

FDX Green. The FDX LED will illuminate when the Adapter is operat-

ing in full duplex mode.

The RJ-45 Port is where you will connect your Category 5 Ethernet Network Cable

or better network cabling.

LEDs

The RJ-45 Port

3 4

EtherFast

10/100 Managed Network Adapter

Figure 2-1

6. Plug one end of a

twisted-pair network

cable into the

Adapter's RJ-45 port,

as shown in Figure 3-

7. Plug the other end of

the cable into a net-

work device, such as

a hub or switch, DSL

modem, cable

modem, router, etc.

8. Reconnect your PC’s

power, then power on

your computer. Your

computer will auto-

matically recognize

the Adapter and

assign it a unique

IRQ ("interrupt") and

I/O address.

TheAdapter’s installation is complete. Next, to install theAdapter’s device

drivers, turn to Chapter 4: Installing theAdapter’s Drivers with the Setup

Utility CD. If your operating system will not install the drivers using the

Setup Utility on the CD or if you’d rather install the drivers manually, turn

to the chapter appropriate to your Operating System.

Instant EtherFast

Series

3. Open your computer and locate the PCI slot(s) on your motherboard. PCI

slots are easily identified by their beige or white color. Remove the metal

slot cover on the back of the PC, then insert the Adapter into an empty PCI

slot, as shown in Figure 3-1.

4. Once the Adapter is firmly in place, secure its fastening tab to your PC's

chassis with a mounting screw.

5. Replace your PC's cover.

Important: When installing the Adapter, be sure to press it solidly into the

PCI slot. The Adapter are built to resist the pressure necessary to insert it

correctly in the PCI slot. Avoid a call to technical support by making sure

that the Adapter is inserted all the way into your PCs network slot! You will

know this has occurred when the Adapters faceplate is flush with your

computers slot.

Figure 3-1

Important: If you intend to use both 10Mbps and 100Mbps

components on your network, you will need an auto-sensing

hub or switch. For more information on auto-sensing hubs or

switches, go to the Linksys website at www.linksys.com.

Figure 3-2

EtherFast

10/100 Managed Network Adapter

3. Click the Install

tab, as shown in

Figure 4-2, and

the installation

process will

begin.

4a. If you are using

Windows 98,

Me or 2000,

the screen

shown in

Figure 4-3 will

appear.

On this screen, you will need to type your computer’s name and your group,

or workgroup, name in the appropriate fields. Then, click the Driver Install

button to continue.

Instant EtherFast

Series

Chapter 4: Installing the Adapter’s

Drivers with the Setup Utility CD

The Adapter’s drivers can easily be installed with the Setup Utility included on

the Setup Utility CD after theAdapter is physically installed into your PC. This

chapter will describe the steps necessary to do this.

The Install Wizard works for installing the drivers under Windows 98, Me,

2000, and XP. To manually install and setup the Adapter on aWindows NT PC,

refer to Chapter 7: Manual Installation and Setup for Windows NT.

1. Start your PC. Windows will automatically detect the presence of the

Adapter in your PC and bring up the Add New Hardware Wizard screen.

Since you will be installing the drivers through the Install Wizard, click the

Cancel button on this screen.

2. Insert the Setup Utility CD into your CD-ROM drive. The Setup Utility’s

Welcome screen, shown in Figure 4-1, will come up automatically and iden-

tify the version

of Windows you

are using.

Figure 4-2

Figure 4-3

Overview

Using the Setup Utility

Figure 4-1

EtherFast

10/100 Managed Network Adapter

Instant EtherFast

Series

4b. If you are using Windows

2000 or XP, the screen

shown in Figure 4-4 will

appear.

5. On this screen, you will need to type your computer’s name in the appro-

priate field. Then, click the Driver Install button to continue. Once the

driver is installed, the NIC Control Set will automatically be installed. This

NIC Control Set is a utility for managing the Adapter.

6. When installation is com-

plete, you will be asked

to restart your computer.

(See Figure 4-5.) Restart

your computer now.

Driver installation is complete!

Chapter 5: Manual Installation and

Setup for Windows 98SE

After physically installing the Adapter in your computer, follow these instruc-

tions to manually install the network device driver. The installation procedure

for the network driver will vary depending on which version of Windows 98

you are using, and on your current system configuration. If at any time during

the installation you encounter problems, refer to the Troubleshooting section.

1. Start up your PC in Windows 98.

2. Windows 98 will automatically detect the presence of the Adapter in your

PC.

3. Insert the Setup Utility CD into your CD-ROM drive while the Add New

Hardware Wizard window is visible. When the screen shown in Figure 5-1

appears, click the Next button.

Installing the Adapter’s Driver

Overview

Figure 5-1

Important: The directions in this Chapter only apply if you

have not already installed the drivers with the Setup Utility CD.

Figure 4-4

Figure 4-5

EtherFast

10/100 Managed Network Adapter

Instant EtherFast

Series

4. Select Search for the best driver for your device (Recommended), as

shown in Figure 5-2, and click the Next button.

5. Select Specify a location and type D:\drivers\win98 in the drop-down box,

as shown in Figure 5-3. Then, click the Next button.

6. A window will open, notifying you that Windows is searching for the

EtherFast 10/100 Managed NetworkAdapter driver.When the window noti-

fies you that it is ready to install the driver, as shown in Figure 5-4, click

the Next

button.

7. Windows will begin copying the Adapter’s driver files to your PC. Refer to

the chart below to help guide you through the process.

 If your PC asks for the Linksys

Setup Utility CD

 If you are asked to supply your

Windows 98 Installation Files

or Disks

 If you are asked for a file that

includes LNE100M or WIN-

NDI.DLL in its name

 If you receive a Version

Conflict error

1. Click OK.

2. Verify that the Setup Utility CD is in your PCs CD-

ROM drive.

3. Type d:\Drivers\Win98 in the Copy files from: box.

4. Click OK.

1. Click OK.

2. If you have a Windows 98 CD-ROM, type d:\win98

in the Copy files from: box, where d: is your CD-

ROM drive.

3. If you dont have a Windows 98 CD-ROM, type

c:\windows\options\cabs.

4. Click OK.

1. Insert the Setup Utility CD into your PCs CD-ROM

drive.

2. Type d:\Drivers\WIN98 in the Copy files from: box.

3. Click OK

1. Choose to keep the newest version of the file by

clicking Yes.

If you press Skip or Cancel, the drivers will not be installed!

Figure 5-4

Figure 5-2

Figure 5-3

EtherFast

10/100 Managed Network Adapter

Autres manuels pour LNE100M

Table des matières

Autres manuels Linksys Carte réseau

Linksys

Linksys WCF11 - Wireless CompactFlash Card Type II Instructions d'utilisation d'origine

Linksys

Linksys EG1064 Instructions d'utilisation d'origine

Linksys

Linksys LNE100M Manuel utilisateur

Linksys

Linksys ProConnect USBHUB04 Manuel utilisateur

Linksys

Linksys EG1064 Manuel utilisateur

Linksys

Linksys EG1032 Instructions d'utilisation d'origine

Linksys

Linksys EG1032 Manuel utilisateur

Linksys

Linksys PAP2 Manuel utilisateur

Linksys

Linksys EC1000 Manuel utilisateur

Linksys

Linksys WCF11 - Wireless CompactFlash Card Type II Manuel utilisateur

Linksys

Linksys WUSB54GSC Instructions d'utilisation d'origine

Linksys

Linksys Wireless USB Network Adapter Instructions d'utilisation

Linksys

Linksys PCMLM56 - EtherFast - 56 Kbps Network Manuel utilisateur

Linksys

Linksys WUSB54GR Manuel utilisateur

Linksys

Linksys EG1032 Instructions d'utilisation d'origine

Linksys

Linksys WDT11 Manuel utilisateur

Linksys

Linksys HomeLink HPN100 Manuel utilisateur

Linksys

Linksys EG1064 Manuel utilisateur

Linksys

Linksys USB200M Manuel utilisateur

Linksys

Linksys EC2T Manuel utilisateur

Linksys

Linksys USB200M Instructions d'utilisation d'origine

Linksys

Linksys WUSBF54G Manuel utilisateur

Linksys

Linksys EC2T Instructions d'utilisation d'origine

Linksys

Linksys HomeLink HPN100 Instructions d'utilisation d'origine

Manuels Carte réseau populaires d'autres marques

FirstComm

FirstComm OBiWiFi5G Manuel utilisateur

Sun Microsystems

Sun Microsystems Interface Adapter Manuel utilisateur

TRENDnet

TRENDnet TU2-ETG Manuel utilisateur

YASKAWA

YASKAWA SI-EN3 Manuel utilisateur

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manuel utilisateur

Belkin

Belkin F5D7050 Manuel utilisateur

3Com

3Com EtherLink 3C509B Manuel utilisateur

TRENDnet

TRENDnet TEG-PCITX Manuel utilisateur

Cisco

Cisco MC16E Manuel utilisateur

Delta Electronics

Delta Electronics Braking Modules VFDB Series Manuel utilisateur

TwinMOS

TwinMOS Booming Manuel utilisateur

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Manuel utilisateur

Buffalo

Buffalo AirStation WLI-PCM-L11GP Manuel utilisateur

National Instruments

National Instruments NI 9234 Manuel utilisateur

Hama

Hama 49276 Manuel utilisateur

Compaq

Compaq Wireless LAN 100 Manuel utilisateur

Bose

Bose PowerMatch Dante Manuel utilisateur

TRENDnet

TRENDnet TEG-PCITXR Manuel utilisateur