Lilin iMegapro IPR7722ESX Manuel utilisateur
IPR7722ESX / LR7722EX
D/N 1080P HD Vari-Focal Infrared IP Camera
66-IPR7722CSM
Quick Installation Guide
CAUTION
Do not drop or strike this equipment
Do not install the equipment near any naked flames or heat
sources
Do not expose this unit to rain, moisture, smoke or dust
environment
Do not cover the opening of the cabinet with cloth and plastic or
to install this unit in poor ventilated places. Allow 10cm between
this unit and its surroundings
Do not continue to operate the unit under abnormal conditions
such as detection of smoke, strange smell or no display on
screen while power is turned on
Do not touch the power connection with wet hands
Do not damage the power cord or leave it under pressure
Do not operate this unit near magnet, speaker system, etc., to
avoid unnecessary magnetic interference
onnection cables should be grounded properly
Part Description & Dimension
Sun Shield
Top over
Bottom hassis
Bracket
Pan Adjustment Screw
Tilt Adjustment Screw
Lens
English
- 1 -
Installation
1. Take out the bracket from the box. Put the D 12V power cable
and network cable through the bracket and then fix it to the wall
(FIG.1 & FIG.2).
2. Take out the camera body and open the top cover with screw
driver (FIG.3).
3. Put the D 12V power cable and network cable through the
bracket rubber and then pull the cables through the bottom of
camera body (FIG.4). onnect the D 12V power cable to the
terminal and connect the network cable to RJ-45 slot of the
camera (FIG.5).
English
- 2 -
4. Use the provided M5.0x10 screws (2 silver ones) to fix the
camera body on the bracket with screw driver (FIG.6).
5. Loose the pan and tilt adjustment screws on the bracket to turn
the camera body to the desired angle and then tighten the
screws (FIG.7).
6. Adjust the lens on focus and zoom for recording clear video
image. After that, tighten the screws (FIG.8).
7. Replace the top cover and tighten the screws (FIG.9 & FIG.10).
English
- 3 -
System Overview
Top View
Input/Output Device Component Description
Alarm In/Out & Audio In/Out onnector
SD ard onnector
RJ-45 Jack
Video Out Jack
Load Default Button
D 12V Power Input onnector
English
- 4 -
System Architectures
For connecting HD IP cameras to the network, please follow one of
the system architectures:
(1). Use D 12V power adapter and a network switch to connect to
the network.
(2). Use a PoE network switch to connect to the network.
(3). Use a PoE power injector and a network switch to connect to
the network.
English
HD IP CAMERA
HD IP CAMERA
HD IP CAMERA
- 5 -
Emergency Factory Default
To restore factory default settings by hardware, please follow these
steps:
1. Hold “RESET Key” for 10 seconds, then release.
2. After about 40 seconds, the network LED light should turn off,
and the back on again.
3. This camera has completed the factory default settings, and can
then reboot.
4. Search for the IP device using the IPScan software.
5. Start the IP device via Internet browser.
6. Enter the default username “admin” and password “pass” to
operate.
NOTE: For user convenience, restoring the factory default settings
will revert to the default IP address 192.168.0.200.
Before Accessing IP Cameras
Before accessing the IP camera, make sure that the camera’s RJ-45
network, audio, and power cables are properly connected. To set the
IP address, consult your network administrator for an available IP
address. The default IP address for each IP camera is 192.168.0.200.
Users can use the default IP address for verifying the camera’s
network connection.
Software Requirements
Merit LILIN Universal ActiveX software components are required for
web interface display of JPEG or H.264 Full HD video. When you login
to the IP camera by Internet Explorer, the security warning dialog box
will prompt the installation of the LILIN Universal ActiveX. lick Install
to download it.
English
- 6 -
Configuring IP Addresses by IPScan Software
To configure an IP address using the IP scan tool, you can copy the
IPScan software from the installation D, and paste to your computer.
Alternatively, you can execute the IPScan software from the
installation D, or download the software from the Merit LILIN
website (www.meritlilin.com). To change the settings of the IP
address, subnet mask, gateway, or HTTP port, you can follow the
steps below:
1. Run the IPScan software.
2. lick Refresh. All available devices should be listed in the device
list.
3. Select your device from the list provided.
4. hange the IP address, subnet mask, gateway, or HTTP port for
the IP camera.
5. lick Apply to submit the settings.
6. lick Refresh to verify the settings.
English
- 7 -
Ce manuel convient aux modèles suivants
1
Table des matières
Langues :
Autres manuels Lilin Caméra de sécurité
Lilin
Lilin 7000MPG4OOE Manuel utilisateur
Lilin
Lilin D/N HD IR IP CAMERA Manuel utilisateur
Lilin
Lilin PSD4624EX20 Manuel utilisateur
Lilin
Lilin MR6322 Manuel utilisateur
Lilin
Lilin IPS6228E Manuel utilisateur
Lilin
Lilin CMG176 Series Manuel utilisateur
Lilin
Lilin Z2R8122X-P Manuel utilisateur
Lilin
Lilin PIH-7635DH Series Manuel utilisateur
Lilin
Lilin PIH-0746XW Manuel utilisateur
Lilin
Lilin ST1358 series Manuel utilisateur
Lilin
Lilin CMW158X2.2 Manuel utilisateur
Lilin
Lilin Z2R8852AX Manuel utilisateur
Lilin
Lilin PIH 7000IP Manuel utilisateur
Lilin
Lilin 66-8322CSB-1B Manuel utilisateur
Lilin
Lilin Z2R8852AXK Manuel utilisateur
Lilin
Lilin AHD DOME IR CAMERA Manuel utilisateur
Lilin
Lilin iMEGAPRO LD2122E Manuel utilisateur
Lilin
Lilin P2 Series Manuel utilisateur
Lilin
Lilin iMEGAPRO IPR7922E Manuel utilisateur
Lilin
Lilin CMD6182X Manuel utilisateur
