Lightspeed Redcat media Manuel utilisateur

Supplied and Serviced by Roberts audio Solutions LTD

User guide – RedCat (Access)

Prioryfield House, 20 Canon Street, Taunton, Somerset, TA1 1SW |

www.robertsaudiosolutions.co.uk |info@robertsaudiosolutions.co.uk |

| 01823 323363

Tel:%07910035358%|%01823323363

Main Unit

Front Panel Indicators

1. Power on indicators: The power LED will glow Blue when

power is supplied

2. MIC 1 & MIC 2: Mic link and registration indicators 2

a. Flashing Amber indicates registration is in process.

b. Solid Green indicates a link has been established

Top Panel Controls

1. MIC VOLUME: Controls the volume level of

the microphones.

2. TONE CONTROL: Adjusts the audio tone,

adding more bass or treble for a more rich

or crisp sound

Side Panel Controls

1. REGISTRATION: Press this button if there is a new component, such

as a microphone, to be registered

2. AUDIO INPUT JACK & VOLUME CONTROL:

3.5mm stereo connector for connecting classroom audio sources to the

Redcat Access. Controls the volume level of the audio input from the

connected audio source.

3. AUDIO OUTPUT JACK & VOLUME

CONTROL: 3.5mm stereo connector for connecting to an assisted

listening device (ALD) or to a computer for recording. Controls the volume

level of the audio output.

4. POWER BUTTON:

This button is used to turn the Redcat Access on or off. The front panel

blue light will glow when power is on.

5. DC INPUT JACK: Plug the power supply (16V/2.0A) into this jack

Page 1

Teachers microphone (Flexmike)

1. POWER/MUTE SWITCH: press and hold to power on,

press to mute, press and hold to power off

2. MIC 1 STATUS: lighted to indicate microphone is

registered as MIC 1

- Blue: solid = normal operation; Blue: flashing =

linking in process

- Red: solid = muted; Red: flashing = muted while

linking in process

3. MIC 2 STATUS: when using a second microphone,

this LED is lighted to indicate microphone is registered

as MIC 2 (same

behaviour as MIC 1 status light above)

4. EARBUD CONNECTION*: connect the earbud for

monitoring

(*for use with Flexcat Pods only)

5. CHARGING/LOW BATTERY INDICATOR: lights Red

when charging, Green when fully charged. When in

operation, turns red to indicate low battery

6. MICROPHONE VOLUME UP/DOWN

7. AUDIO INPUT: Connect audio source to send Redcat

Access

8. LANYARD INTERFACE: insert the lanyard into this

hook to wear the Flexmike.

9. BATTERY DOOR: remove the battery door to replace

the rechargeable battery pack

10. REGISTRATION: (inside battery compartment - not

shown) only used when adding or replacing Flexmike

Operating the Flexmike

The Flexmike will automatically power on and mute when it is

removed from the charger. This will automatically

power on the Redcat Access as well.

While speaking in a normal voice, fine-tune the microphone

volume on top of the Redcat Access up or down. Proper

volume level should be as follows:

- Your voice should be heard by another person on the

other side of the room

- You should barley be able to hear your own voice

- There should not be any audio “feedback” or

squealing outside of 2-3 feet. If there is turn the main

volume down slightly

Page 2

Prioryfield House, 20 Canon Street, Taunton, Somerset, TA1 1SW |

www.robertsaudiosolutions.co.uk |info@robertsaudiosolutions.co.uk |

| 01823 323363

Tel:%07910035358%|%01823323363

Flexmike Cradle Charger

1. DC POWER PORT: Connect the

5V/1.0A DC power cord here

2. OPTIONAL USB CHARGING

PORT: Plug the charging cord for

the optional Sharemike microphone

here.

Prioryfield House, 20 Canon street, Taunton, Somerset, TA1 1SW |

www.robertsaudiosolutions.co.uk |info@robertsaudiosolutions.co.uk |

Tel:079100353538 | 01823323363

Tel:%07910035358%|%01823323363

Output to assistive listening

device

1. Turn the ALD (Assistive Listening

Device) volume control on the Redcat

Access side panel counter clockwise all

the way down

2. Determine the size and type of audio

input jack on the device.

3. Connect a patch cable from the ALD’s

microphone jack or AUX input to the

3.5mm audio jack labelled “ALD OUT”

on the side of the Redcat

4. With the Redact and ALD turned on,

speak into the Flexmike and slowly

adjust the ALD volume control until the

appropriate audio level is attained in the

ALD’s receiver headphones.

5. It may be necessary to adjust the

volume on the persona; FM receiver to

achieve appropriate volume level.

Sharemike

1. POWER BUTTON

2. MIC 2 LIGHT: This light indicated operation

status when Sharemike is registered as mic 2

(Standard)

- Blue: solid = normal operation,

blinking - link in progress

- Red: solid = muted

3. MIC 1 LIGHT: This light indicates battery /

charging status when Sharemike us registered

as MIC 2

- Red flashing = low battery

- Red solid = charging

- Green solid = charging complete

Note: the functions of these lights are reversed

when a Sharemike is registered as MIC 1

4. AUDIO INPUT: Plug a laptop, MP3 player or

other audio device into this jack to wirelessly

transmit the audio signal to be played through

the system

5. REGISTRATIONBUTTON: Located in the

battery compartment, only used when adding or

replacement Sharemike

6. CHARGER INPUT: Plug the charging cable from

the Sharemike charger into this jack

Page 3

Prioryfield House, 20 Canon street, Taunton, Somerset, TA1 1SW |

www.robertsaudiosolutions.co.uk |info@robertsaudiosolutions.co.uk |

Tel:079100353538 | 01823323363

Tel:%07910035358%|%01823323363

Page 4

Pairing up teachers microphone with the main system:

https://www.lightspeed-tek.com/support/tutorials/tutorial-library/redcat-access-registration-

tutorial/register-sharemike-to-redcat-access/

Pairing up students microphone with the main system:

https://www.lightspeed-tek.com/support/tutorials/tutorial-library/redcat-access-registration-

tutorial/register-flexmike-to-redcat-access/

Both microphones should be paired (registered) with the

main unit However, if you have difficulty please follow

the two links below which take you to an on-line video

which should be able to help you….

Charging

1. Make sure the charger is plugged in to a wall

socket. Connect one end of the charging

cable into the jack labelled CHARGE on the

bottom of the Sharemike

2. Plug the other end into the USB jack on the

back of the cradle charger

3. If the Sharemike is registered as MIC 2, the

MIC 1 light on the microphone will glow Red

to indicated charging

4. Leave the Sharemike plugged in overnight

(8-10 hours) to obtain a full charge. The light

will turn green when charged is complete.

5. During charge the Blue light will stay on

Other similar products that we can provide:

These provide fantastic digital stereo sound via a teacher and student

microphone. The Juno hub doesn't just amplify the teacher’s voice but allows the

students to interact with each other in the class with the use of their own

microphones. It’s ideal for use in the modern classroom and also allows hearing

devices to be connected up to it, discreetly benefiting staff or students who are

hard-of-hearing.

Autres manuels pour Redcat media

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Lightspeed Système stéréo

Lightspeed

Lightspeed flexcat Manuel utilisateur

Lightspeed

Lightspeed Cat 855 Manuel utilisateur

Lightspeed

Lightspeed Redcat media Manuel utilisateur

Lightspeed

Lightspeed Redcat media Manuel utilisateur

Lightspeed

Lightspeed 850iR Manuel utilisateur

Lightspeed

Lightspeed Active Manuel utilisateur

Lightspeed

Lightspeed RedcatAccess Manuel utilisateur

Lightspeed

Lightspeed Access Link Manuel utilisateur

Lightspeed

Lightspeed Redcat Access LSRCA 1881 Manuel utilisateur

Lightspeed

Lightspeed flexcat Manuel utilisateur

Lightspeed

Lightspeed Cascadia C25 Manuel utilisateur

Lightspeed

Lightspeed Redcat media Manuel utilisateur

Lightspeed

Lightspeed 705iR Manuel utilisateur

Lightspeed

Lightspeed Redcat media Manuel utilisateur

Lightspeed

Lightspeed Redcat media Manuel utilisateur

Lightspeed

Lightspeed Redcat media Manuel utilisateur

Lightspeed

Lightspeed ActivateStation Manuel utilisateur

Lightspeed

Lightspeed flexcat Manuel utilisateur

Lightspeed

Lightspeed Mobile PA Manuel utilisateur

Lightspeed

Lightspeed CAT 860 Manuel utilisateur

Lightspeed

Lightspeed 975 Manuel utilisateur

Lightspeed

Lightspeed Redcat media Manuel utilisateur

Lightspeed

Lightspeed TOPCAT Manuel utilisateur

Lightspeed

Lightspeed CAT 860 Manuel utilisateur

Manuels Système stéréo populaires d'autres marques

LG CM3330B Manuel utilisateur

Sony

Sony SS-CEP50 Manuel utilisateur

Cetacea Sound

Cetacea Sound CVS-II Manuel utilisateur

Aiwa

Aiwa XR-H66MD Manuel utilisateur

Denon

Denon UCD-250 Manuel utilisateur

Sanyo

Sanyo DC-MX41i Manuel utilisateur

Sharp

Sharp CD-ES600V Manuel utilisateur

Exibel

Exibel BDX600-UK Manuel utilisateur

Sanyo

Sanyo DC-F320 Manuel utilisateur

Philips

Philips FWM583X Manuel utilisateur

Sharp

Sharp CD-C462 Manuel utilisateur

Onkyo

Onkyo CBX 300 - CD / MP3 Clock Radio Manuel utilisateur

Aiwa

Aiwa XR-EM70 Manuel utilisateur

Cyrus

Cyrus Lyric Manuel utilisateur

Philips

Philips MCM159/98 Manuel utilisateur

Philips/Magnavox

Philips/Magnavox Magnavox FW 62C Manuel utilisateur

RCA

RCA RS3965SB Manuel utilisateur

Sharp

Sharp XL-UH240 Manuel utilisateur