Lightolier Lytecaster 1100F Series Manuel utilisateur

NEW CONSTRUCTION

1. FRAME-IN (FIG. A)

WOOD JOIST/METAL STUD CONSTRUCTION (FIG. E): Line up bot-

tom edge of ADJUSTABLE MOUNTING BAR with bottom of wood joist.

Fasten MOUNTING FRAME to

wood joist by nailing MOUNTING BAR

TAB or nail into joist.

SUSPENDED GRID CEILING (FIG. G):

Position notched area of ADJUSTABLE MOUNTING BARS on top of T-

BAR for proper spacing to finished ceiling. Lock MOUNTING BARS by

bending TAB underneath T-BAR BEAD (Fig. G1). For round T-BAR BEAD,

use screws to lock MOUNTING BARS (Fig. G2).

WIRE TO SUPPLY LEADS:

For cable, use built-in cable clamp in J-Box. Connect white fixture

leads to neutral (white) supply leads. Black fixture leads to hot (black)

supply leads. Bare fixture wire to supply ground. Use wirenuts (local

hardware item). Place all electrical connections in the J-Box, attach J-

Box cover.

NOTE: ADJUSTABLE MOUNTING BARS are pre-assembled on long side of

MOUNTING FRAME for rigidity and ease of installation (Fig. E).

MOUNTING BARS must be removed and installed on narrow side of

MOUNTING FRAME if installing in 16” joist spacing (Fig. F).

MOUNTING BARS can be extended to 24”. The MOUNTING FRAME

can be mounted off-center.

For suspended ceilings, make certain that bottom of MOUNTING

FRAME is no higher than 1” above finished ceiling (Fig. G).

2. CLOSE-IN (FIG. B)

Install plasterboard or other dry type ceiling. Hole in board can be cut

either on floor or after the board is secured in the ceiling. Use MOUNT-

ING FRAME opening as cutting guide template for hole – make sure

ROTO CLIPS are rotated out of hole area.

NOTE: For wet plaster ceiling, use Plaster Ring Accessory No. 1961 - order

separately.

3. SNAP-ON (FIG. C) See separate instruction sheet

4. PUSH-UP (FIG. D) for your choice of reflector trim.

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.

This fixture is intended for installation in accordance with the National Electrical Code and local or Federal

code specifications. To assure full compliance with codes and regulations, check with your local electrical

inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

INSTRUCTION SHEET NO.

IS:1100F

D0605 Page 1of 2

Installation of Lytecaster®Frame-in-Kit 1100F Series

WARNING – (RISK OF FIRE) Do not install insulation within 3 inches of fixture sides or wiring

compartments, nor above fixture in such a manner as to entrap heat.

LOCKING SCREW

LINE UP BOTTOM

EDGE WITH BOTTOM

OF WOOD JOIST

MOUNTING FRAME

CENTERING SLOTS

ADJUSTABLE

MOUNTING BARS

T-BAR

1" MAX

1-1/2" MAX.

G1 G2

Fig. G

Fig. E

ADJUSTABLE MOUNTING BARS MOUNTING FRAME

(NARROW SIDE)

LINE UP BOTTOM EDGE WITH

BOTTOM OF WOOD JOIST

Fig. F

ADJUSTABLE MOUNTING BARS

Fig. A

1. Frame-In Fig. B

2. Close-in Fig. C

3. Snap-On Fig. D

4. Push-Up

LIGHTOLIER a GENLYTE company.

631 Airport Road, Fall River, MA 02720

INSTRUCTION SHEET NO.

IS:1100F

D0605 PAGE 2OF 2

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.

This fixture is intended for installation in accordance with the National Electrical Code and local or Federal

code specifications. To assure full compliance with codes and regulations, check with your local electrical

inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

MOUNTING FRAME

BRIDGE

SLOT

Fig. H

ROTO CLIP

STAPLE

MOUNTING FRAME

CEILING MATERIAL

Fig. I

FRAME

J-BOX COVER

J-BOX

J-BOX SPRING

J-BOX COVER

Fig. J

BALLAST REPLACEMENT (FIG. J)

NOTE: Ballast replacement must be provided by a “qualified electrician”.

1. TURN OFF POWER.

2. Remove reflector trim from FRAME-IN KIT.

3. Remove J-BOX COVER nearest ceiling opening by lifting SPRING.

4. Disconnect all input wiring to ballast.

5. Remove BALLAST ASSEMBLY from J-BOX by pulling SPRING upward

(Fig. J).

6. Remove BALLAST ASSEMBLY through ceiling opening.

7. Release all wires from BALLAST WIRE CONNECTORS by inserting small

blade tool, with insulated handle, into WIRE RELEASE SLOTS. (Fig K).

NOTE: Replacement ballast kits generally are supplied with this special

wire release tool.

8. Remove (2) NUTS which hold BALLAST to J-BOX COVER.

9. Replace old BALLAST with new BALLAST and attach with NUTS

to J-BOX COVER.

10.Reassemble new BALLAST ASSEMBLY to J-BOX by snapping

onto J-BOX spring (Fig. J).

11.Rewire fixture. See WIRING DIAGRAM on BALLAST LABEL.

EXISTING CONSTRUCTION

Fig. A

1. Cut-Opening Fig. B

2. Wire-in Fig. C

3. Put Through Fig. D

4. Anchor Fig. F

6. Push-up

Fig. E

5. Snap-on

LIGHTOLIER a GENLYTE company.

631 Airport Road, Fall River, MA 02720

REMOVE

INSERT

BALLAST WIRE

CONNECTORS

WIRE RELEASE

BLADE

(BY OTHERS)

WIRE RELEASE

SLOTS

1. CUT OPENING (FIG. A AND FIG H)

a. Remove ADJUSTABLE MOUNTING BARS.

b. Use MOUNTING FRAME opening as template.

c. Break off BRIDGE on MOUNTING FRAME as shown in

Fig. H by breaking WEBS on SLOTS with cutting plier.

2. WIRE-IN (FIG. B)

For cable, use built in Cable Clamp in J-BOX. Connect white fixture

lead to neutral (white) supply lead. Black fixture leads to hot (black)

supply lead. Bare copper and/or green insulated wire(s) must all be

connected to supply ground. Use wire nuts (local hardware items).

Place all electrical connections in the

J-BOX. Attach J-BOX COVER onto J-BOX.

3. PUT THROUGH (FIG. C AND FIG. J)

Detach BALLAST ASSEMBLY from J-BOX and pass MOUNTING

FRAME into ceiling as shown in Fig. C. Reattach BALLAST ASSEMBLY.

4. ANCHOR (FIG. D AND FIG. I)

Using STAPLE (order separately Cat. #1985S), slide long end under-

neath raised embossing and short leg into ceiling (Fig. I).

5. SNAP-ON (FIG. E) See separate instruction sheet

6. PUSH-UP (FIG. F) for your choice of reflector trim.

Autres manuels Lightolier Luminaire

Lightolier

Lightolier WES SERIES 2X4 Manuel utilisateur

Lightolier

Lightolier ProSpec 26070 Manuel utilisateur

Lightolier

Lightolier Lytespan 8640WH Manuel utilisateur

Lightolier

Lightolier GUARDSMAN GV4WB332 Manuel utilisateur

Lightolier

Lightolier IS-CTS3_FLNGLSS Mode d’emploi

Lightolier

Lightolier 22XX6 series Manuel utilisateur

Lightolier

Lightolier 4F23 Manuel utilisateur

Lightolier

Lightolier Lytespan 6273B Manuel utilisateur

Lightolier

Lightolier Calculite AF2PF Manuel utilisateur

Lightolier

Lightolier Calculite C6T6A-MHT6RF Manuel utilisateur

Lightolier

Lightolier QVS2GPFLV317 Manuel utilisateur

Lightolier

Lightolier QVS2GPFOB232 Manuel utilisateur

Lightolier

Lightolier Lytespan 8292WECY Manuel utilisateur

Lightolier

Lightolier QVS2GPFLV332 Manuel utilisateur

Lightolier

Lightolier D13 Manuel utilisateur

Lightolier

Lightolier Lytecaster 1179M1 Manuel utilisateur

Lightolier

Lightolier LIS6G20LW154 Manuel utilisateur

Lightolier

Lightolier Lytecel-EL EL4MF10LX228 Manuel utilisateur

Lightolier

Lightolier Calculite AS4LS Manuel utilisateur

Lightolier

Lightolier QVL2GPFSS2FT Manuel utilisateur

Lightolier

Lightolier SM T5 Strip Manuel utilisateur

Lightolier

Lightolier Calculite CS8142 Manuel utilisateur

Lightolier

Lightolier 5453 Mode d’emploi

Lightolier

Lightolier H9S2GLR254 Manuel utilisateur

Manuels Luminaire populaires d'autres marques

Emos

Emos CLASSIC ZY1431T Manuel utilisateur

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuel utilisateur

Hedler

Hedler C 12 silent Manuel utilisateur

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuel utilisateur

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuel utilisateur

Lightmaxx

Lightmaxx Shaft 5R Manuel utilisateur

Triarch

Triarch 31083 Manuel utilisateur

Philips

Philips 32614 Series Manuel utilisateur

IKEA

IKEA TIVED Manuel utilisateur

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuel utilisateur

Martin

Martin MAC 250 Krypton Manuel utilisateur

Cooper Lighting

Cooper Lighting Halo L3232E Manuel utilisateur

Stageline

Stageline ODW-2410RGBW Manuel utilisateur

Light Sky

Light Sky Tornado Series Manuel utilisateur

ArtFox

ArtFox Beam 15R extreme Manuel utilisateur

GLG

GLG multispot 330 Manuel utilisateur

Home Accents Holiday

Home Accents Holiday TY052-1924-1 Manuel utilisateur

SELF Electronics

SELF Electronics FLEX Manuel utilisateur