LG EBR81777301 Manuel utilisateur

1. User Manual

This user manual gives a brief overview of how to use EBR81777301 ZigBee Module.

2. Product Overview

EBR81777301 ZigBee Module provides the connectivity between two products. This allows

a user to manage and control product and monitor product status from the another product.

EBR81777301 ZigBee Module is installed in home appliances.

3. Specifications

- ZigBee Standard : 802.15.4

- Host Interface : UART Interface

- Operating Temperature : -10 ~ 70℃

- Operating Voltage : 4.5V ~ 5.5V

- Frequency Range : 2405MHz ~ 2480MHz

- Channels : 16ch.

- Type of Modulation : DSSS(OPQSK)

- Output Power : 1 dBm

- Antenna Type : Pattern Antenna

4. Function Block

▣Block Diagram

1) ZigBee

- SoC Module including Microcontroller and ZigBee chipset

2) Level shift circuits

- Signal level shift circuits to communicate between appliance and 81777301 ZigBee module by

UART interface and output signal.

3) DC-DC Converter

- DC 5V converted to DC 3.3V

4) Main Connector

- Connect ZigBee Module with appliance

5. ZigBee Setup

1) Enter “Quick Setting” by flicking indicator.

2) Enter the More Settings.

3) Enter the Washer Pairing.

4) Proceed pairing by touching “Pair”button.

5) Two EBR81777301 Modules are connected.

[ENGLISH]

Hereby, LG Electronics European Shared Service Center B.V., declares that this ZigBee module

is in compliance with the essential requirements and other relevant provisions of Directive

1999/5/EC. The complete Declaration of Conformity may be requested through the following

postal address:

LG Electronics European Shared Service Center B.V.

Krijgsman 1

1186 DM Amstelveen

The Netherlands

or can be requested at our dedicated DoC website:

http://www.lg.com/global/support/cedoc/cedoc#

This device is a 2.4 GHz wideband transmission system, intended for use in all EU member

states and EFTA countries.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and the receiver.

- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference and

(2) this device must accept any interference received, including interference that may cause undesired

operation of the device.

Any changes or modifications in construction of this device which are not expressly approved by the

party responsible for compliance could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

This equipment should be installed and operated with a minimum distance of 20 cm (7.8 inches) between

the antenna and your body. Users must follow the specific operating instructions for satisfying RF

exposure compliance.

Industry Canada Statement

This device complies with Industry Canada’s applicable licence-exempt RSSs. Operation is subject to the

following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation

of the device.

Avis d’Industrie Canada

Cet appareil est conforme aux normes CNR d’Industrie Canada applicables aux appareils radio exempts

de licence. Son

fonctionnement est sujet aux deux conditions suivantes :

1) Cet appareil ne doit pas provoquer d’interférences, et

2) Cet appareil doit accepter toutes les interférences, y compris celles pouvant entraîner son

dysfonctionnement.

IC Radiation Exposure Statement

This equipment complies with IC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 20 cm (7.8

inches) between the antenna and your body.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY

UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE

USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

Avis d’Industrie Canada sur l’exposition aux rayonnements

Cet appareil est conforme aux limites d’exposition aux rayonnements d’Industrie Canada pour un

environnement non contrôlé. Cet appareil doit être installé de façon à garder une distance minimale de

20 cm (7,8 po) entre la source de rayonnement et votre corps.

REMARQUE : LE FABRICANT N’EST PAS RESPONSABLE DES INTERFÉRENCES

RADIOÉLECTRIQUES CAUSÉES PAR DES MODIFICATIONS NON AUTORISÉES APPORTÉES À CET APPAREIL.

DE TELLES MODIFICATIONS POURRAIENT ANNULER L’AUTORISATION ACCORDÉE À L’UTILISATEUR DE

FAIRE FONCTIONNER L’APPAREIL.

OEM Responsibilities to comply with FCC and Industry Canada Regulations

The module has been certified for integration into products only by OEM integrators under the

following condition:

-The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is

maintained between the radiator (antenna) and all persons at all times.

-The transmitter module must not be co-located or operating in conjunction with any other antenna

or transmitter except in accordance with FCC multi-transmitter product procedures.

As long as the two condition above is met, further transmitter testing will not be required. However,

the OEM integrator is still responsible for testing their end-product for any additional compliance

requirements required with this module installed (for example, digital device emissions, PC

peripheral requirements, etc.).

End Product Labeling

The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC

Certification Number are not visible when the module is installed inside another device, then the

outside of the device into which the module is installed must also display a label referring to the

enclosed module. In that case, the final end product must be labeled in a visible area with the

following:

“Contains FCC ID: BEJ-EBR81777301

“Contains IC: 2703N-EBR81777301”

Étiquetagedu produitfinal (IC)

Le module BT111 est étiqueté avec sa proper identification FCC et son proper numéro de

certification IC. Si l’identification FCC et le numéro de certification IC ne sont pas visibles lorsque

le module est installé à l’intérieur d’un autre dispositif, la partie externe du dispositif dans lequel

le module est installé devra également presenter une etiquette faisant reference au module inclus.

Dans ce cas, le produit final devra être étiqueté sur une zone visible avec les informations

suivantes:

« Contient module émetteur identification FCC ID : BEJ-EBR81777301

« Contient module émetteur IC : 2703N-EBR81777301”

Table des matières

Autres manuels LG Unité de contrôle

LG LG Q1C-V5 Series Manuel utilisateur

LG ACP 5 Manuel utilisateur

LG LGSBWAC61 Manuel utilisateur

LG N1C-A5 Series Manuel utilisateur

LG V-Net PQDSBNGCM1 Manuel utilisateur

LG PRVC1 Manuel utilisateur

LG MB8811C1 Manuel utilisateur

LG LGSWFAC81 Manuel utilisateur

LG LGSBW51 Manuel utilisateur

LG PRCKD42E Manuel utilisateur

LG PMNFP14A0 Manuel utilisateur

LG V-NET ACS IO Mode d’emploi

LG PQNFG14B0 Manuel utilisateur

LG LGXXXQ1CK-A5 Manuel utilisateur

LG LG325N1CW-V5 Manuel utilisateur

LG WL1BKR22 Manuel utilisateur

LG LCWB-002 Manuel utilisateur

LG V-NET PDRYCB400 Manuel utilisateur

LG MULTI V EEV KIT AIR Manuel utilisateur

LG PQCSC101S0 Guide de démarrage rapide

LG V-net PDRYCB000 Manuel utilisateur

LG ETWCERBC01 Manuel utilisateur

LG LGSBWAC03 Manuel utilisateur

LG LG N1CW-N5 Series Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur