LG PMNFP14A0 Manuel utilisateur

P/NO : MFL57868530

INSTALLATION MANUAL

PMNFP14A0 / PMNFP14A1

AIR

CONDITIONER

www.lg.com

Please read this installation manual completely before installing the product.

Installation work must be performed in accordance with the national wiring

standards by authorized personnel only.

Please retain this installation manual for future reference after reading it

thoroughly.

(PI485)

ENGLISH

PORTUGUESE

MALTI

MAGYAR

SLOVENČINA

БЪЛГАРСKN

SLOVENŠČINA

SRPSKI

LATVIEŠU VALODA

HRVATSKI

LIETUVIŲ KALBA

SVENDKA

GAEILGE

NORSK

МАКЕДОНСКИ

SUOMI

SHQIP

DANSK

ÍSLENSKA

EESTI KEEL

BOSANSKI

ITALIANO ESPAÑOL FRANÇAIS DEUTSCH

ΕΛΛΗΝΙΚΆ

ČEŠTINA

NEDERLANDS

POLSKI

LIMBA ROMÂNĂ

2SAFETY PRECAUTIONS

ENGLISH

SAFETY PRECAU-

TIONS

To prevent injury to the user or other people

and property damage, the following instruc-

tions must be followed.

•

Incorrect operation due to ignoring instruction

will cause harm or damage. The seriousness

is classified by the following indications.

WARNING

This symbol indicates the possibility of death

or serious injury.

CAUTION

This symbol indicates the possibility of injury

or damage.

• Meanings of symbols used in this manual

are as shown below.

WARNING

Installation

• Don't touch with the hands while the

power is on.

- There is risk of fire or electric shock.

• Use standard parts(connector).

- Do not disassemble or repair the product.

There is risk of fire or electric shock.

•

For electrical work, contact the dealer, seller, a quali-

fied electrician, or an Authorized Service Center.

- Do not disassemble or repair the product.

There is risk of fire or electric shock.

• Use the correctly rated breaker or fuse.

- There is risk of fire or electric shock.

• Do not install, remove, or re-install the unit

by yourself (customer).

- There is risk of fire, electric shock, explo-

sion, or injury.

• For installation, always contact the dealer

or an Authorized Service Center.

- There is risk of fire, electric shock, explo-

sion, or injury.

Operation

•

When the product is soaked (flooded or sub-

merged), contact an Authorized Service Center.

- There is risk of fire or electric shock.

•

Be cautious that water could not enter the product.

- There is risk of fire, electric shock, or prod-

uct damage.

PART DESCRIPTION

PMNFP14A0 / PMNFP14A1

NOTE

RS-485 is one of the international inter-

face standards for serial communication.

12345678















* The location of parts might be different in case of

PMNFP14A1.

PMNFP14A0 : For connecting 1 ~ 16 Indoor Units

PMNFP14A1 : For connecting 1 ~ 64 Indoor Units

PI485 GATEWAY(M)

LED01G, 02G, 03G: Communication

Status LED

LED1:RS-485 Status LED

CN_PWR: 220V~ Connector

+10V: DC 10 V Terminal

GND: Ground

BUS_A: *RS-485 (+) Terminal (Refer to

note)

BUS_B: RS-485 (-) Terminal

DIP Switch: Product Selection (Refer to

theDIP Switch Configuration)

CN_OUT: Outdoor Unit Connector

Reset Switch: PI485(M) Reset

NOTE

Install and use by qualified personnel only.

ACCEASSORY PARTS 3

ENGLISH

1. Connect CN_OUT with Outdoor Unit by

the cable (provided)

2. Connect RS-485 BUS_A(+) and

BUS_(B)(-) with other network products

(ex. Central Controller , I-Gateway.....)

3. In case of using Simple Central

Controller, connect VCC(+10V) and GND.

No need to connect otherwise.

4. Select DIP Switch Configuration.

5. Connect CN_PWR with Outdoor PCB

Power connector

6. After Power is ON, check the

Communication LED

- LED1G(Red)

• Normal : LED blinks as many as the

number of Connected Indoor

units, and then turns OFF.

This process is repeated after

every 3 minutes

• Error : Check the Indoor Unit's

address & wiring connections

- LED2G(Yellow), LED3G(Orange)

• Normal : LED blinks continuously

• Error : Check the DIP Switch setting &

wiring connections

7. Check RS-485 Communication Status

LED:

• Normal : LED blinks when PI485

receives data from central con-

troller.

• Error : Check the wiring connections

8. Finally if all of the above steps are OK, then

tie the cables by tie wraps & clamp.

* Example about Multi V plus.

ACCEASSORY PARTS

Others : Tie Wrap (3 EA) - Cable Tie

Clamp (1 EA)

PI485 : PMNFP14A0(1EA)

or PMNFP14A1(1EA)

Multi-V

Multi

BRACKET (1EA)

WIRE ASSY 1(1EA)

WIRE ASSY 2(1EA) WIRE ASSY 3(1EA)

SCREW (4EA)

INSTALLATION GUIDE

Installation Steps

Install the PI485 on the Noise Filter in

Multi V plus.

Install the PI485 after checking the hole

for screw.

CAUTION

4INSTALLATION GUIDE

ENGLISH

Multi V & Multi(LGAP applied) products

Configuration Methods

12345678

1234 5678

12345678

‘1 ON, All others OFF : Multi V products(Except CRUN

products) or Multi(Non-Inverter) Product applied

Common PCB(Refer to NOTE) or Multi(Inverter)

Product + Central Controller(All types) - Without LGAP

‘1 and 4 ON, All others OFF : Multi V products(Except

CRUN products) or Multi(Non-Inverter) Product

applied Common PCB or Multi(Inverter) Product +

Central Controller(All types) - Using LGAP

‘2 ON, All others OFF : Multi(Non-Inverter)

Product + Centroller(All types) - Without LGAP

‘2 and 4 ON, All others OFF : Multi Non-

Inverter Product

+ Central Controller(All Types) - Using LGAP

‘1,2,3,4 ON : Multi V CRUN Product

+ Central Controller(All types) - Using LGAP

The wrong setting of air-conditioner switch could

cause malfunctioning. Switch setting must be

done carefully. Push the Reset button after

changing the Dip switch.

CAUTION

NOTE

Multi(Non-Inverter) Product applied

Common PCB

PCB P/NO. : 6871A20917*

P/NO. : 6871A20918*

P/NO. : 6871A20910*

* Please refer the corresponding Central Controller

installation manual if you want to know whether your

Central Controller is compatible with LGAP or not.

Advanced Lock Control Type

- To use the advanced lock function (Run

Mode lock, Fan Speed lock,

Temperature Lock, and Temperature Range

lock; adjustable only within certain boundary)

by central controller, Set up the fifth dip

switch according to the type of outdoor prod-

uct.

- In case of advanced lock function, it can use

only the central controller applied to LGAP.

‘1, 4 and 5 ON, All others OFF :

MultiV Products (Except CRUN

products) or MPS Inverter

Product + Central Controller

(All types) - Using LGAP

‘2, 4 and 5 ON, All others OFF :

Multi Standard Product +

Central Controller (All types) -

Using LGAP

‘1, 2, 3, 4and 5 ON, All others

OFF : MultiV CRUN Product +

Central Controller (All types) -

Using LGAP

NOTE

The advanced lock setting.

Some products do not support advanced lock

function.

In this case, The fifth dip switch on PI485 must

be on.

In case of product applied to advanced function, it

can process the advanced lock function without

fifth dip switch ON.

If all units support advanced lock function, It is

recommended that the fifth dip switch be off, so

that advanced lock function is processed faster.

DIP Switch Conﬁguration

1234 5678

12345678

Select Air

Conditioer Type

Select Network Type

Select Advanced Control Type

*LGAP: LG Air conditioner Protocol

Representative

LG Electronics Inc. EU Representative, Krijgsman 1, 1186

DM Amstelveen, The Netherlands

Manufacturer

LG Electronics Inc. Changwon 2nd factory, 84, Wanam-ro,

Seongsan-gu, Changwon-si, Gyeongsangnam-do, KOREA

Autres manuels pour PMNFP14A0

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels LG Unité de contrôle

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur