Lantech mini Switch 800 Manuel utilisateur
mini Switch 800
User Guide
mini Switch 800
8 Port 10/100 Base-TX Switch
with Auto MDI/MDI-X
Rev. 1.0 June, 2003
User Guide
1. Introduction
Welcome to the World of Mini-Networking.
In the modern business society, communication and sharing information is crucial.
Computer networks have proven to be one of the fastest modes of communication.
Lantech Mini Switch 800 is compacts and attractively designed for desktop use.
It is an ideal solution for small of ce or SOHO network user. The Switch provides
wire-speed, Fast Ethernet switching function that allows high-performance,
low-cost connection.
Mini Switch 800 will automatically detect the speed of the device that you plug
into it to allow you to use both 10 and 100Mbps device. It features a store-and
forward switching and it can auto-learn and store source address.
•Features
- Conforms to IEEE 802.3, 802.3u and 802.3x standard
- 8-Port 10/100M Fast Ethernet Switch
- Auto MDI/MDI-X for cascading
- N-way auto-negotiation supported
- Half-duplex for backpressure, full-duplex for ow control
- Store-and-forward switching architecture
- MAC address table – 8Port: 1K
- Memory buffer sharing – 8 Port: 128K bytes
- LED indicators – 8 port: Power, LK/ACT, FDX/COL,100
- External power supply
•Size:
- 165mm(W) x 86mm(D) x 23mm (H) Palm size
1
mini Switch 800
User Guide
•Package Contents
- 8-Port Switch
- One DC power adapter
- Rubber Feet
- User’s Guide
- 8TP Auto MDI/MDI-X Switch - Rubber Feet
- DC power Adapter - User’s Guide
Figure 1-2. Package Contents
Compare the contents of your Mini Switch 800 with the standard checklist above.
If any item is missing or damaged, please contact your local dealer for service.
2
mini Switch 800
User Guide
2. Hardware Description
This section mainly describes the hardware of the Lantech Mini Switch 800
The physical dimensions of the 8-Port Switch is:
165mm(W) X 86mm(D) x 23mm(H)
•Front Panel
The LED indicators are located on the frond panel of the Switch. They
provide a real-time indication of systematic operation status. The Front
Panels 8-Port Switch is displayed in the following gures.
Figure 2-1. The Front Panel of Mini Switch 800
•LED Indicators
The following table provides descriptions of the LED statuses and their
meaning.
LED Status Color Description
Power On Green The power of the Switch is On
LNK/ACT
On
Green
The port is successfully connecting with the device.
Blinks The port is receiving or transmitting data.
Off No device attached.
FDX/COL
On
Green
The port is operating in Full-duplex mode.
Blinks Collision of Packets occurs in the port.
Off Half-duplex mode.
100 On Green In 100Mbps mode
Off In 10Mbps mode
LED Indicators
Power LED
3
mini Switch 800
User Guide
•Rear Panel
The Rear Panel of the Mini Switch 800 consists of 8x 10/100 N-Way UTP
switch ports, and one DC power connector.
Figure 2-2. The Rear Panel of the 8-Port Switch
- RJ-45 Ports:
8x 10/100N-Way auto-sensing for 10Base-T or 100Base-TX connection.
- Auto MDI/MDI-X:
It can detect the cable straight connect NIC or cascade to a hub or
switch without change the connector, the maximum distance between the
Switch to another device is 100 meters.
- DC Power Connector:
Plug DC Power Adapter’s female end into this device, and the male end
of the DC Power Adapter into a power outlet. The Adapter supply the
Switch with Voltage 7.5V, Current 1000mA.
DC 7.5V
+87654321
4
mini Switch 800
User Guide
3.Network Application
This section provides you a few examples of network topology in which the Mini
Switch 800 is used, the Switch is design to be used as a desktop or segment
switch.
The switch automatically learns node address, which are subsequently used to
lter and forward all traf c based on the destination address.
•Stand Alone
The Mini Switch 800 is designed to be a compact desktop size switch,
which is an ideal solution for small workgroup. The Switch can be used as
a standalone switch to which personal computers, server, printer server are
directly connected to form small workgroup.
Figure 3-1. Stand Alone Application
5
mini Switch 800
User Guide
•Enlarge Your Network
You can use Uplink port of the Mini Switch 800 to connect with another
hub or switch to interconnect each of your small switched workgroup to
form a large switched network.
You can connect anyone switch port to hub or switch without crossover
cable by the Auto MDI/MDI-X function.
In the below illustration, two Switches are used to interconnect two small
workgroup. All the devices in this network can communicate with each
other. Connecting servers to the Switch allow other users to access the
server’s data.
Figure 3-2. Example of enlarging your network
6
mini Switch 800
User Guide
4. Trouble Shooting
The Mini Switch 800 can be easily monitored through panel indicators to assist in
identifying problems. This section describes common problems you may encounter
and where you can nd possible solutions.
•Diagnosing LED Indicators
If Link indicator does not light up after making a connection, you may
check whether network interface (e.g., a network adapter card on the
attached device), network cable, or switch port is defective or not. Be
sure the cable is plugged into both the Switch and corresponding device.
Veri ed the proper cable type is used and its length does not exceed
speci ed limits.
•Power
If the power indicator does not turn on when the power cord is plugged
in, you may have a problem with power outlet, or power cord. However,
if the switch powers off after running for a while, check for loose power
connection, power loses or surges at power outlet. If you still cannot
resolve the problem, contact your local dealer for assistance.
•Cabling
RJ-45 Ports: Use unshielded twisted-pair (UTP) or shield twisted-pair (STP)
cable for RJ-45 connections: 100Ω Category 3,4 or 5 Cable for 10Mbps
connections or 100Ω Category 5 Cable for 100Mbps connections. Also
be sure that the length of any twisted-pair connection does not exceed 100
meters ( 328 feet ).
7
mini Switch 800
User Guide
5.Technical Specification
This section provides the speci cations of the Mini Switch 800 :
•Speci cation
Standards Compliance IEEE 802.3 10BASE-T Ethernet,
IEEE 802.3u 100BASE-TX Fast Ethernet
ANSI/IEEE standard 802.3 N-Way auto-negotiation
Protocol CSMA/CD
Max Forwarding Rate
and Max Filtering Rate
14,880 pps Ethernet port,
148,800 pps per Fast Ethernet port
LED Indicators Per Port: Link/Activity, Full/Collision
Per Unit: Power
Network Cables 10Base-T:
2-pair UTP Cat. 3, 4, 5 cable (100m),
EIA/TIA-568 100-ohm STP (100m)
100Base-TX:
2-pair UTP Cat. 5 cable (100m),
EIA/TIA-568 100-ohm STP (100m)
Dimensions 165mm x 86mm x 23mm (W x D x H)
Operating Temperature 0ºC to 45ºC (32ºF to 113ºF)
Operating Humidity 10% to 90% (Non-condensing)
External Power Supply DC 7.5V, 1000mA
Power Consumption 4.2 Watt
EMI FCC Class B, CE Mark
8
mini Switch 800
User Guide
• Federal Communications commission (FCC) Statement
This Equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of FCC rules. These limits are
designed to pro reasonable protection against harmful interference in a
residential installation. This equipments generates, uses and can radiate
radio frequency energy and, if not stalled and used in accordance with
the instruction, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measure:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• Warning
[A shielded-type power cord is required in order to meet FCC emission
limits and also prevent interference to the nearby radio and television
reception. It is essential that only the supplied power cord be used.]
[Use only shielded cables to connect I/O device to this equipment.]
You are cautioned that changes or modi cations not expressly approved
by the party responsible for compliance could void your authority to
operate the equipment.
9
Table des matières
Autres manuels Lantech Changer
Lantech
Lantech IPGS-0204DSFP-12V Manuel utilisateur
Lantech
Lantech IPES-0208 Series Manuel utilisateur
Lantech
Lantech IES-2008B-DNV Manuel utilisateur
Lantech
Lantech IES-0208CA Manuel utilisateur
Lantech
Lantech IES-5416DF Series Manuel utilisateur
Lantech
Lantech IES-2208CA-DNV Manuel utilisateur
Lantech
Lantech IES-5216DF Manuel utilisateur
Lantech
Lantech 2204F Series Manuel utilisateur
Lantech
Lantech IPES-0008B Series Manuel utilisateur
Lantech
Lantech IPES-3408 Series Manuel utilisateur
Lantech
Lantech IES-5416T Series Manuel utilisateur
Lantech
Lantech IPWMR-3006 Manuel utilisateur
Lantech
Lantech IES-2208CA Manuel utilisateur
Lantech
Lantech IPES/IES-0008B Series Manuel utilisateur
Lantech
Lantech 5 10/100TX w/ 4 PoE Injector Industrial... Manuel utilisateur
Lantech
Lantech LPES-2208CA Manuel utilisateur
Lantech
Lantech LGS-2816C-RPS Manuel utilisateur
Lantech
Lantech IES-3208C Manuel utilisateur
Lantech
Lantech IPGS-5 Series Manuel utilisateur
Lantech
Lantech IPES-0208CA-12V Manuel utilisateur
