Kramer VS-42H2 Manuel utilisateur
VS-42H2 Quick Start (P/N: 2900-300947QS REV 1)
P/N:
2900- 300947QS
Rev:
1
Scan for full manual
VS-42H2 Quick Start Guide
This guide helps you install and use your VS-42H2.
Go to www.kramerav.com/manual/VS-42H2 to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check What’s in the Box
VS-42H2
4x2 HDMI Matrix Switcher
4 Rubber feet Infrared remote control transmitter
1 Power supply (5V DC)
1 Quick start guide
Step 2: Get to know your VS-42H2
# Feature Function
1
IR LED
Lights yellow when receiving an IR signal.
2 IR Sensor Receives signals from the infrared remote control transmitter.
3
ON LED
Lights green when the device is powered on.
4 INPUT SELECTOR
TO OUT 1, 1–4
Press one of the four inputs to switch it to OUT 1.
5 INPUT SELECTOR
TO OUT 2, 1–4
Press one of the four inputs to switch it to OUT 2.
6 MUTE OUT 2 Button Press to toggle mute of the OUT 2 signal.
7
MUTE OUT 1 Button
Press to toggle mute of the OUT 1 signal.
8 EDID Button Press to capture the EDID (see Step 6).
9
LOCK Button
Press and hold to lock the front panel buttons. Press and hold again to unlock.
# Feature Function
10
INPUT 1–4 HDMI Input Connectors
Connect to up to four HDMI sources.
11 REMOTE IR Opening Connect to an external IR receiver for controlling the device via an IR remote controller.
Covered by a cap. The 3.5mm mini jack at the end of the internal IR connection cable fits
into this opening.
12 REMOTE INPUT TO OUT 1
4-pin Terminal Block + Ground
Connect to up to four remote, contact-closure input selection switches for Output 1.
13 REMOTE INPUT TO OUT 2
4-pin Terminal Block + Ground
Connect to up to four remote, contact-closure input selection switches for Output 2.
14
RS-232 3-pin Terminal Block
Connect to a PC/serial controller.
15 SETUP 8-way DIP-Switch Sets the device configuration.
16
PROG VIA USB Connector
Connect to a PC to upgrade the firmware.
17 FACTORY PROG
VIA RS-232 Upgrade Switch
Press to upgrade the firmware via the RS-232 port, release for normal operation.
18
ETHERNET RJ-45 Connector
Connect to a PC via a LAN.
19 RESET Switch Press while power-cycling the device to reset to factory default parameters.
20
5V DC Connector
Connect to the power adapter, center pin positive.
21 OUT 1 and OUT 2 HDMI Output
Connectors
Connect to up to two HDMI acceptors.
Step 3: Install VS-42H2
Attach the rubber feet and place on a table or mount VS-42H2 in a rack (using an optional RK-T2B rack mount).
Step 4: Connect the inputs and outputs
Always
switch OFF the
power on each device
before connecting it to your
VS
-42H2. For best results,
we recommend that you
always use Kramer high
-
performance cables to
connect AV equipment to
VS
-42H2.
Connecting the remote input selection switches:
These remote switches replicate the input selection buttons on the front panel of VS-42H2.
Step 5: Connect the power
Connect the 5V DC power adapter to VS-42H2 and plug it into the mains electricity.
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Use only the Kramer Electronics power adapter that is provided with the unit.
Warning:
Disconnect the power and unplug the unit from the wall before installing.
See www.KramerAV.com for updated safety information.
Step 6: Operate VS-42H2
Operate VS-42H2 via:
•Front panel buttons
•Remotely, via RS-232 serial
commands transmitted by a touch
screen system, PC, or other serial
controller
•Remotely, using an IR remote
control transmitter
•Embedded web pages via the
Ethernet
•Contact-closure switches
RS-232 / Protocol 3000 Default Parameters
Baud Rate: 115,200
Data Bits: 8
Stop Bits: 1
Parity: None
Command Format:
ASCII
TCP/IP Default Parameters
IP Address: 192.168.1.39
Netmask: 255.255.0.0
Gateway: 0.0.0.0
TCP Port #: 5000
UDP Port #: 50000
Switch an input to an output:
•Press an input button on the top row (To OUT 1) to switch that input to Output 1.
•Press an input button on the bottom row (To OUT 2) to switch that input to Output 2.
Copy the EDID from an Output to one or more Inputs:
1. Press the EDID button to enter the EDID setting mode.
The EDID button lights.
Note: If there is no button activity for 10 seconds, the device automatically exits the EDID setting mode to normal operation, the EDID
button no longer lights and any changes made are lost.
2. From the To OUT 1 (top) row, press each of the Inputs to which you want to copy the EDID from Output 1.
Each selected Input LED lights.
3. From the To OUT 2 (bottom) row, press each of the Inputs into which you want to copy the EDID from Output 2.
Each selected Input LED lights.
4. Press the EDID button.
The button no longer lights and the EDID changes are saved.
Copy the default EDID to one or more Inputs:
1. Press the EDID button to enter the EDID setting mode.
The EDID button lights.
2. For each Input to which you want to copy the default EDID, press both the To OUT 1 and To OUT 2 buttons simultaneously.
Both top row and bottom row Input LEDs light.
3. Press the EDID button.
The button no longer lights and the EDID changes are saved.
Set the HDCP status for each input using the DIP-switches:
Note: Push the DIP-switch up for ON and down for OFF.
Switch # Description
1 OFF – Input 1 does not support HDCP
ON – Input 1 is HDCP compliant
2 OFF – Input 2 does not support HDCP
ON – Input 2 is HDCP compliant
3 OFF – Input 3 does not support HDCP
ON – Input 3 is HDCP compliant
4 OFF – Input 4 does not support HDCP
ON – Input 5 is HDCP compliant
Set the automatic switching mode for each output using the DIP-switches:
1. Use DIP-switch 5 (input 1) or 7 (input 2) to select manual or automatic switching for the output.
2. If automatic is selected, use DIP-switch 6 (input 1) or 8 (input 2) to select the automatic switching mode.
Note: Push the DIP-switch up for ON and down for OFF.
Switch # Description
5 OFF – Output 1: Manual switching
ON – Output 1: Automatic switching
6 OFF – Output 1: Last Connected mode
ON – Output 1: Priority mode
7 OFF – Output 2: Manual switching
ON – Output 2: Automatic switching
8 OFF – Output 2: Last Connected mode
ON – Output 2: Priority mode
Autres manuels pour VS-42H2
1
Table des matières
Autres manuels Kramer Commutateur matriciel
Kramer
Kramer VS-4x4YCx1 Manuel utilisateur
Kramer
Kramer VS-3232DN-EM Manuel utilisateur
Kramer
Kramer VS-88UT Manuel utilisateur
Kramer
Kramer XL 3216V2 Manuel utilisateur
Kramer
Kramer Sierra Pro XL 1616V3S Manuel utilisateur
Kramer
Kramer VS-3232DN Manuel utilisateur
Kramer
Kramer VS-88HD Manuel utilisateur
Kramer
Kramer VS-3232A Manuel utilisateur
Kramer
Kramer VP-1608 Manuel utilisateur
Kramer
Kramer MTX3-34-M Manuel utilisateur
Kramer
Kramer VS-606xl Manuel utilisateur
Kramer
Kramer VS-4216 Manuel utilisateur
Kramer
Kramer VP-4x4 Manuel utilisateur
Kramer
Kramer VS-42UHD Manuel utilisateur
Kramer
Kramer 1616DS Manuel utilisateur
Kramer
Kramer VP-772T Manuel utilisateur
Kramer
Kramer VS-402XL Manuel utilisateur
Kramer
Kramer VP-725DS Manuel utilisateur
Kramer
Kramer VP-32K Manuel utilisateur
Kramer
Kramer VS-84HDCPxl Manuel utilisateur
Manuels Commutateur matriciel populaires d'autres marques
AMX
AMX AVS-OP-2020-117 Instructions et recettes
Lindy
Lindy 38042 Manuel utilisateur
Extron electronics
Extron electronics MTPX Plus Series Manuel utilisateur
Key Digital
Key Digital Champion KD-16x16CS Manuel utilisateur
Shinybow USA
Shinybow USA SB-8811 Manuel utilisateur
Optimus
Optimus Compact Manuel utilisateur